Abstract: Unmanned aerial vehicles (UAVs) performing their
operations for a long time have been attracting much attention in
military and civil aviation industries for the past decade. The
applicable field of UAV is changing from the military purpose only to
the civil one. Because of their low operation cost, high reliability and
the necessity of various application areas, numerous development
programs have been initiated around the world. To obtain the optimal
solutions of the design variable (i.e., sectional airfoil profile, wing
taper ratio and sweep) for high performance of UAVs, both the lift and
lift-to-drag ratio are maximized whereas the pitching moment should
be minimized, simultaneously. It is found that the lift force and
lift-to-drag ratio are linearly dependent and a unique and dominant
solution are existed. However, a trade-off phenomenon is observed
between the lift-to-drag ratio and pitching moment. As the result of
optimization, sixty-five (65) non-dominated Pareto individuals at the
cutting edge of design spaces that are decided by airfoil shapes can be
obtained.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: This paper addresses a stock-cutting problem with rotation of items and without the guillotine cutting constraint. In order to solve the large-scale problem effectively and efficiently, we propose a simple but fast heuristic algorithm. It is shown that this heuristic outperforms the latest published algorithms for large-scale problem instances.
Abstract: The chatter is one of the major limitations of the productivity in the ball end milling process. It affects the surface roughness, the dimensional accuracy and the tool life. The aim of this research is to propose the new system to detect the chatter during the ball end milling process by using the wavelet transform. The proposed method is implemented on the 5-axis CNC machining center and the new three parameters are introduced from three dynamic cutting forces, which are calculated by taking the ratio of the average variances of dynamic cutting forces to the absolute variances of themselves. It had been proved that the chatter can be easier to detect during the in-process cutting by using the new parameters which are proposed in this research. The experimentally obtained results showed that the wavelet transform can provide the reliable results to detect the chatter under various cutting conditions.
Abstract: There is inadequate information on the practice of
female genital mutilation (FGM) in the UK, and there are often
myths and perceptions within communities that influence the
effectiveness of prevention programmes. This means it is difficult to
address the trends and changes in the practice in the UK.
To this end, FORWARD undertook novel and innovative research
using the Participatory Ethnographic and Evaluative Research
(PEER) method to explore the views of women from Eritrea, Sudan,
Somalia and Ethiopia that live in London and Bristol (two UK cities).
Women-s views, taken from PEER interviews, reflected reasons for
continued practice of FGM: marriageability, the harnessing and
control of female sexuality, and upholding traditions from their
countries of origin. It was also clear that the main supporters of the
practice were believed to be older women within families and
communities.
Women described the impact FGM was having on their lives as
isolating. And although it was clearly considered a private and
personal matter, they developed a real sense of connection with their
peers within the research process.
The women were overwhelmingly positive about combating the
practice, although they believed it would probably take a while
before it ends completely. They also made concrete
recommendations on how to improve support services for women
affected by FGM: Training for professionals (particularly in
healthcare), increased engagement with, and outreach to,
communities, culturally appropriate materials and information made
available and accessible to communities, and more consequent
implementation of legislation.
Finally, the women asked for more empathy and understanding,
particularly from health professionals. Rather than presenting FGM
as a completely alien and inconceivable practice, it may help for
those looking into these women-s lives and working with them to
understand the social and economic context in which the practice
takes place.
Abstract: Titanium alloys like Ti-6Al-2Sn-4Zr-6Mo (Ti-
6246) are widely used in aerospace applications. Component
manufacturing, however, is difficult and expensive as their
machinability is extremely poor. A thorough understanding of the
chip formation process is needed to improve related metal cutting
operations.In the current study, orthogonal cutting experiments have
been performed and theresulting chips were analyzed by optical
microscopy and scanning electron microscopy.Chips from aTi-
6246ingot were produced at different cutting speeds and cutting
depths. During the experiments, depending of the cutting conditions,
continuous or segmented chips were formed. Narrow, highly
deformed and grain oriented zones, the so-called shear zone,
separated individual segments. Different material properties have
been measured in the shear zones and the segments.
Abstract: Monitoring the tool flank wear without affecting the
throughput is considered as the prudent method in production
technology. The examination has to be done without affecting the
machining process. In this paper we proposed a novel work that is
used to determine tool flank wear by observing the sound signals
emitted during the turning process. The work-piece material we used
here is steel and aluminum and the cutting insert was carbide
material. Two different cutting speeds were used in this work. The
feed rate and the cutting depth were constant whereas the flank wear
was a variable. The emitted sound signal of a fresh tool (0 mm flank
wear) a slightly worn tool (0.2 -0.25 mm flank wear) and a severely
worn tool (0.4mm and above flank wear) during turning process were
recorded separately using a high sensitive microphone. Analysis
using Singular Value Decomposition was done on these sound
signals to extract the feature sound components. Observation of the
results showed that an increase in tool flank wear correlates with an
increase in the values of SVD features produced out of the sound
signals for both the materials. Hence it can be concluded that wear
monitoring of tool flank during turning process using SVD features
with the Fuzzy C means classification on the emitted sound signal is
a potential and relatively simple method.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: The purpose of study was to design and construction
the semi-automatic sliced ginger machine for reduce production times
in sheet and slice ginger procedure furthermore, reduced amount of
labor of slides and cutting method. Take consider into clean and safety of workers and consumers. The principle of machines, used 1
horsepower motor, rotation speed of sliced blade 967 rpm, the diameter of sliced dish 310 mm, consists of 2 blades for sheet cutting
ginger and the power from motor which transfer to rotate the sliced blade roller, rotation speed 440 rpm. The slice cutter roller was sliced
ginger from sheet ginger to line ginger. The conveyer could
adjustment level of motors, used to the beginning area that sheet
ginger was transference to the roller for sheet and sliced cutting in next process. The cover of sliced cutting had channel for 1 tuber of
ginger. The semi-automatic sliced ginger machine could produced sheet ginger 81.8 kg/h (6.2 times of labor) and line ginger 17.9 kg/h
(2.5 times of labor) compare with, labor work could produced sheet
ginger 13.2 kg/h and line ginger 7.1 kg/h, and when timekeeper, the
total times of semi auto machine 30.86 kg/h and labor 4.6 kg/h, there
for the semi auto machine was 6.7 times of labor. The semiautomatic
sliced ginger machine convenient, easy for use and
maintain, in addition to reduce fatigue of body and seriousness from
works; must be used high skill, and protection accident in slicing
procedure. Beside, machine could used with other vegetables for
example potato, carrot .etc
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Abstract: The aim of this paper is to experimentally discover the workability coefficient of the Inconel 718 material by using a slide turning machining. Two different types of cutting inserts, one made of carbide and the other one made of ceramic, are being used. The purpose is to compare measured results and recommend the appropriate materials and cutting parameters for a machining of the Inconel 718. Furthermore, the durability of inserts with the chosen wear criterion is being compared for different cutting speeds. Machinability of these materials is a crucial characteristic as it allows us to shorten the technological cycle time and increase the machining productivity. And this is of great importance from an economic point of view.
Abstract: This paper describes a combined mathematicalgraphical
approach for optimum tool path planning in order to
improve machining efficiency. A methodology has been used that
stabilizes machining operations by adjusting material removal rate in
pocket milling operations while keeping cutting forces within limits.
This increases the life of cutting tool and reduces the risk of tool
breakage, machining vibration, and chatter. Case studies reveal the
fact that application of this approach could result in a slight increase
of machining time, however, a considerable reduction of tooling cost,
machining vibration, noise and chatter can be achieved in addition to
producing a better surface finish.
Abstract: This paper presents an experimental investigation on
the machinability of laser-sintered material using small ball end mill focusing on wear mechanisms. Laser-sintered material was produced
by irradiating a laser beam on a layer of loose fine SCM-Ni-Cu powder. Bulk carbon steel JIS S55C was selected as a reference steel.
The effects of powder consolidation mechanisms and unsintered
powder on the tool life and wear mechanisms were carried out. Results indicated that tool life in cutting laser-sintered material is
lower than that in cutting JIS S55C. Adhesion of the work material and chipping were the main wear mechanisms of the ball end mill in
cutting laser-sintered material. Cutting with the unsintered powder
surrounding the tool and laser-sintered material had caused major fracture on the cutting edge.
Abstract: This paper deals with the evaluation of flow properties
of polymeric matrix with natural animal fillers. Technical university
of Liberec cooperates on the long-term development of “green
materials“ that should replace conventionally used materials
(especially in automotive industry). Natural fibres (of animal and
plant origin) from all over the world are collected and adapted
(drying, cutting etc.) for extrusion processing. Inside the extruder
these natural additives are blended with polymeric (synthetic and
biodegradable - PLA) matrix and created compound is subsequently
cut for pellets in the wet way. These green materials with unique
recipes are then studied and their mechanical, physical and
processing properties are determined. The main goal of this research
is to develop new ecological materials very similar to unfilled
polymers. In this article the rheological behaviour of chosen natural
animal fibres is introduced considering their shape and surface that
were observed with use of SEM microscopy.
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.