Abstract: Haynes 25 alloy (also known as L-605 alloy) is cobalt
based super alloy which has widely applications such as aerospace
industry, turbine and furnace parts, power generators and heat
exchangers and petroleum refining components due to its excellent
characteristics. However, the workability of this alloy is more
difficult compared to normal steels or even stainless. In present work,
an experimental investigation was performed under cryogenic
cooling to determine cutting tool wear patterns and obtain optimal
cutting parameters in turning of cobalt based superalloy Haynes 25.
In experiments, uncoated carbide tool was used and cutting speed (V)
and feed rate (f) were considered as test parameters. Tool wear
(VBmax) were measured for process performance indicators.
Analysis of variance (ANOVA) was performed to determine the
importance of machining parameters.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: Chemical vapor deposition (CVD) diamond coated
cutting tool has excellent cutting performance, it is the most ideal tool
for the processing of nonferrous metals and alloys, composites,
nonmetallic materials and other difficult-to-machine materials
efficiently and accurately. Depositing CVD diamond coating on the
cemented carbide with high cobalt content can improve its toughness
and strength, therefore, it is very important to research on the
preparation technology and cutting properties of CVD diamond coated
cemented carbide cutting tool with high cobalt content. The
preparation technology of boron-doped diamond (BDD) coating has
been studied and the coated drills were prepared. BDD coating were
deposited on the drills by using the optimized parameters and the SEM
results show that there are no cracks or collapses in the coating.
Cutting tests with the prepared drills against the silumin and aluminum
base printed circuit board (PCB) have been studied. The results show
that the wear amount of the coated drill is small and the machined
surface has a better precision. The coating does not come off during
the test, which shows good adhesion and cutting performance of the
drill.
Abstract: Metal matrix composites (MMCs) attract considerable
attention as a result from its ability in providing a high strength, high
modulus, high toughness, high impact properties, improving wear
resistance and providing good corrosion resistance compared to
unreinforced alloy. Aluminium Silicon (Al/Si) alloy MMC has been
widely used in various industrial sectors such as in transportation,
domestic equipment, aerospace, military, construction, etc.
Aluminium silicon alloy is an MMC that had been reinforced with
aluminium nitrate (AlN) particle and become a new generation
material use in automotive and aerospace sector. The AlN is one of
the advance material that have a bright prospect in future since it has
features such as lightweight, high strength, high hardness and
stiffness quality. However, the high degree of ceramic particle
reinforcement and the irregular nature of the particles along the
matrix material that contribute to its low density is the main problem
which leads to difficulties in machining process. This paper examined
the tool wear when milling AlSi/AlN Metal Matrix Composite using
a TiB2 (Titanium diboride) coated carbide cutting tool. The volume
of the AlN reinforced particle was 10% and milling process was
carried out under dry cutting condition. The TiB2 coated carbide
insert parameters used were at the cutting speed of (230, 300 and
370m/min, feed rate of 0.8, Depth of Cut (DoC) at 0.4m). The
Sometech SV-35 video microscope system used to quantify of the
tool wear. The result shown that tool life span increasing with the
cutting speeds at (370m/min, feed rate of 0.8mm/tooth and DoC at
0.4mm) which constituted an optimum condition for longer tool life
lasted until 123.2 mins. Meanwhile, at medium cutting speed which
at 300m/m, feed rate of 0.8mm/tooth and depth of cut at 0.4mm we
found that tool life span lasted until 119.86 mins while at low cutting
speed it lasted in 119.66 mins. High cutting speed will give the best
parameter in cutting AlSi/AlN MMCs material. The result will help
manufacturers in machining process of AlSi/AlN MMCs materials.
Abstract: This paper reports an advanced approach in the application of CNC machining for rapid manufacturing processes (CNC-RM). The aim of this study is to improve the quality of machined parts by introducing different cutting tools during finishing operations. As the cutting is performed in different directions, the surfaces presented on part can be classified into several categories. Therefore, suitable cutting tools are assigned to machine particular surfaces and to improve the quality. Experimental studies have been carried out by fabricating several parts based on the suggested approach. The results provide further support for implementing this approach in rapid machining processes.
Abstract: The wear of cutting tool degrades the quality of the product in the manufacturing processes. The on line monitoring of the cutting tool wear level is very necessary to prevent the deterioration of the quality of machining. Unfortunately there is not a direct manner to measure the cutting tool wear on line. Consequently we must adopt an indirect method where wear will be estimated from the measurement of one or more physical parameters appearing during the machining process such as the cutting force, the vibrations, or the acoustic emission etc…. In this work, a neural network system is elaborated in order to estimate the flank wear from the cutting force measurement and the cutting conditions.
Abstract: This paper is intended to develop an artificial neural network (ANN) based model of material removal rate (MRR) in the turning of ferrous and nonferrous material in a Indian small-scale industry. MRR of the formulated model was proved with the testing data and artificial neural network (ANN) model was developed for the analysis and prediction of the relationship between inputs and output parameters during the turning of ferrous and nonferrous materials. The input parameters of this model are operator, work-piece, cutting process, cutting tool, machine and the environment.
The ANN model consists of a three layered feedforward back propagation neural network. The network is trained with pairs of independent/dependent datasets generated when machining ferrous and nonferrous material. A very good performance of the neural network, in terms of contract with experimental data, was achieved. The model may be used for the testing and forecast of the complex relationship between dependent and the independent parameters in turning operations.
Abstract: Determination of optimal conditions of machining parameters is important to reduce the production cost and achieve the desired surface quality. This paper investigates the influence of cutting parameters on surface roughness and natural frequency in turning of aluminum alloy AA2024. The experiments were performed at the lathe machine using two different cutting tools made of AISI 5140 and carbide cutting insert coated with TiC. Turning experiments were planned by Taguchi method L9 orthogonal array.Three levels for spindle speed, feed rate, depth of cut and tool overhang were chosen as cutting variables. The obtained experimental data has been analyzed using signal to noise ratio and analysis of variance. The main effects have been discussed and percentage contributions of various parameters affecting surface roughness and natural frequency, and optimal cutting conditions have been determined. Finally, optimization of the cutting parameters using Taguchi method was verified by confirmation experiments.
Abstract: Paper is dealing by testing of IN23 ceramic cutting tools at irregular shocks at special fixture - interrupted cut simulator. Standard tests provided at fixture were at regular interrupted cut at 4 slats by 90°. These new tests will be at irregular cut for 1 slat, 2 slats against each other, 2 slats side by side, 3 slats and 4 slats. The main goal is check if irregular shocks have influence at mechanical and thermal shock at tool life of cutting inserts.
Abstract: In this study, WC-Ni-based cemented carbides having different nickel contents were used as the substrate for cutting tool materials. Hardened steel was turned by a (Ti,W,Si)N-coated WC-Ni-based cemented carbide tool, and the tool wear was experimentally investigated. The following results were obtained: (1) In the (Ti,W,Si)N-coated WC-Ni-based cemented carbide, the hardness of the coating film was not much different from the content of the binding material, Ni, and the adhesion strength increased with a decrease in Ni content. (2) There is little difference between the wear progress of the (Ti,W,Si)N-coated WC-7%Ni-based cemented carbide tool and that of the (Ti,W,Si)N-coated WC-6%Co-based cemented carbide tool. (3) The wear progress of the (Ti,W,Si)N-coated WC-Ni-based cemented carbide became slower with a decrease in Ni content.
From the above, it is has become clear that WC-Ni-based cemented carbide can be used as a substrate for cutting tool materials.
Abstract: The article deals with the possibilities of increasing the efficiency of turning thin-walled workpieces. It proposes a new strategy for turning and it proposes new implementation of roughing cycles where a variable depth of cut is applied. Proposed roughing cycles are created in the CAD/CAM system. These roughing cycles are described in relation to their further use in practice.
The experimental research has focused on monitoring the durability of cutting tool and increases its tool life. It compares the turning where the standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied. In article are monitored tool wear during cutting with the sintered carbide cutting edge. The result verifies theoretical prerequisites of tool wear.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: Production of hard-to-cut materials with uncoated carbide cutting tools in turning, not only cause tool life reduction but also, impairs the product surface roughness. In this paper, influence of hot machining method were studied and presented in two cases. Case1-Workpiece surface roughness quality with constant cutting parameter and 300 ºC initial workpiece surface temperature. Case 2- Tool temperature variation when cutting with two speeds 78.5 (m/min) and 51 (m/min). The workpiece material and tool used in this study were AISI 1060 steel (45HRC) and uncoated carbide TNNM 120408-SP10(SANDVIK Coromant) respectively. A gas flam heating source was used to preheating of the workpiece surface up to 300 ºC, causing reduction of yield stress about 15%. Results obtained experimentally, show that the method used can considerably improved surface quality of the workpiece.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: This paper describes a combined mathematicalgraphical
approach for optimum tool path planning in order to
improve machining efficiency. A methodology has been used that
stabilizes machining operations by adjusting material removal rate in
pocket milling operations while keeping cutting forces within limits.
This increases the life of cutting tool and reduces the risk of tool
breakage, machining vibration, and chatter. Case studies reveal the
fact that application of this approach could result in a slight increase
of machining time, however, a considerable reduction of tooling cost,
machining vibration, noise and chatter can be achieved in addition to
producing a better surface finish.
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.
Abstract: This paper deals with the problem of thermal and
mechanical shocks, which rising during operation, mostly at
interrupted cut. Here will be solved their impact on the cutting edge
tool life, the impact of coating technology on resistance to shocks
and experimental determination of tool life in heating flame.
Resistance of removable cutting edges against thermal and
mechanical shock is an important indicator of quality as well as its
abrasion resistance. Breach of the edge or its crumble may occur due
to cyclic loading. We can observe it not only during the interrupted
cutting (milling, turning areas abandoned hole or slot), but also in
continuous cutting. This is due to the volatility of cutting force on
cutting. Frequency of the volatility in this case depends on the type
of rising chips (chip size element). For difficult-to-machine materials
such as austenitic steel particularly happened at higher cutting speeds
for the localization of plastic deformation in the shear plane and for
the inception of separate elements substantially continuous chips.
This leads to variations of cutting forces substantially greater than for
other types of steel.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool