Abstract: Testing the first year students of Informatics at the
University of Debrecen revealed that students start their tertiary
studies in programming with a low level of programming knowledge
and algorithmic skills. The possible reasons which lead the students
to this very unfortunate result were examined. The results of the test
were compared to the students’ results in the school leaving exams
and to their self-assessment values. It was found that there is only a
slight connection between the students’ results in the test and in the
school leaving exams, especially at intermediate level. Beyond this,
the school leaving exams do not seem to enable students to evaluate
their own abilities.
Abstract: Different order modulations combined with different
coding schemes, allow sending more bits per symbol, thus achieving
higher throughputs and better spectral efficiencies. However, it must
also be noted that when using a modulation technique such as 64-
QAM with less overhead bits, better signal-to-noise ratios (SNRs) are
needed to overcome any Inter symbol Interference (ISI) and maintain
a certain bit error ratio (BER). The use of adaptive modulation allows
wireless technologies to yielding higher throughputs while also
covering long distances. The aim of this paper is to implement an
Adaptive Modulation and Coding (AMC) features of the WiMAX
PHY in MATLAB and to analyze the performance of the system in
different channel conditions (AWGN, Rayleigh and Rician fading
channel) with channel estimation and blind equalization. Simulation
results have demonstrated that the increment in modulation order
causes to increment in throughput and BER values. These results
derived a trade-off among modulation order, FFT length, throughput,
BER value and spectral efficiency. The BER changes gradually for
AWGN channel and arbitrarily for Rayleigh and Rician fade
channels.
Abstract: Non-linear FEM calculations are indispensable when important technical information like operating performance of a rubber component is desired. Rubber bumpers built into air-spring structures may undergo large deformations under load, which in itself shows non-linear behavior. The changing contact range between the parts and the incompressibility of the rubber increases this non-linear behavior further. The material characterization of an elastomeric component is also a demanding engineering task. In this paper a comprehensive investigation is introduced including laboratory measurements, mesh density analysis and complex finite element simulations to obtain the load-displacement curve of the chosen rubber bumper. Contact and friction effects are also taken into consideration. The aim of this research is to elaborate a FEM model which is accurate and competitive for a future shape optimization task.
Abstract: Cesiumiodide with Na doping (CsI(Na)) solution or melt is easily forming three- dimension dendrites on the free surface. The defects or bobbles form inside the CsI(Na) during the solution or melt solidification. The defects or bobbles can further effect the x-ray path in the CsI(Na) crystal and decrease the scintillation characteristics of CsI(Na). In order to enhance the CsI(Na) scintillated property we made single crystal of CsI(Na) column in the anodic aluminum oxide (AAO) template by hydraulic pressure injection method. It is interesting that when CsI(Na) melt is confined in the small AAO channels, the column grow as stable single column without any dendrites. The high aspect ratio (100~10000) of AAO and nano to sub-micron channel structure which is a suitable template for single of crystal CsI(Na) formation. In this work, a new low-cost approach to fabricate scintillator crystals using anodic aluminum oxide (AAO) rather than Si is reported, which can produce scintillator crystals with a wide range of controllable size to optimize their performance in X-ray detection.
Abstract: Many researchers have suggested the use of zero inflated Poisson (ZIP) and zero inflated negative binomial (ZINB) models in modeling overdispersed medical count data with extra variations caused by extra zeros and unobserved heterogeneity. The studies indicate that ZIP and ZINB always provide better fit than using the normal Poisson and negative binomial models in modeling overdispersed medical count data. In this study, we proposed the use of Zero Inflated Inverse Trinomial (ZIIT), Zero Inflated Poisson Inverse Gaussian (ZIPIG) and zero inflated strict arcsine models in modeling overdispered medical count data. These proposed models are not widely used by many researchers especially in the medical field. The results show that these three suggested models can serve as alternative models in modeling overdispersed medical count data. This is supported by the application of these suggested models to a real life medical data set. Inverse trinomial, Poisson inverse Gaussian and strict arcsine are discrete distributions with cubic variance function of mean. Therefore, ZIIT, ZIPIG and ZISA are able to accommodate data with excess zeros and very heavy tailed. They are recommended to be used in modeling overdispersed medical count data when ZIP and ZINB are inadequate.
Abstract: The study aims to determine which factors account for customer satisfaction and to investigate the relationship between entrepreneurial orientation and business success, in particular, context of the information understanding of hostel business in Pranakorn district, Bangkok and the significant element of entrepreneurship in tourism industry. This study covers 352 hostels customers and 61 hostel owners/managers nearby Khao San road. Data collection methods were used by survey questionnaire and a series of hypotheses were developed from services marketing literature. The findings suggest the customer satisfaction most influenced by image, service quality, room quality and price accordingly. Furthermore the findings revealed that significant relationships exist between entrepreneurial orientation and business success; while competitive aggressiveness was found unrelated. The ECSI model’s generic measuring customer satisfaction was found partially mediate the business success. A reconsideration of other variables applicable should be supported with the model of hostel business. The study provides context and overall view of hostel business while discussing from the entrepreneurial orientation to customer satisfaction, thereby reducing decision risk on hostel investment.
Abstract: We examined the crop yield results of hybrids in 2012. We found out that in the control treatments the lowest yield was reached with the hybrid PR37M81: 10,012 kg ha-1. The highest yield was in case of hybrid P37N01: 11,581 kg ha-1. As we raised the nutrient doses the lowest yield of all examined nutrient levels was in case of hybrid PR37M81. We measured at N60+PK nutrient level 12,517 kg ha-1, at N120+PK nutrient level 12,760 kg ha-1, and at N150+PK nutrient level 12,535 kg ha-1 yield results. At N60+PK and N120+PK nutrient level the highest yield was reached with the hybrid P9494 (N60+PK: 13,970 kg ha-1, N120+PK: 13,871 kg ha-1). In case of the N150+PK fertilization treatment the hybrid P37N01 gave the highest yield results (13,962 kg ha-1).
Abstract: The performance of state of the art worldwide telecommunication networks strongly depends on the efficiency of the applied routing mechanism. Game theoretical approaches to this problem offer new solutions. In this paper a new continuous network routing model is defined to describe data transfer in fixed telecommunication networks of multiple hosts. The nodes of the network correspond to routers whose latency is assumed to be traffic dependent. We propose that the whole traffic of the network can be decomposed to a finite number of tasks, which belong to various hosts. To describe the different latency-sensitivity, utility functions are defined for each task. The model is used to compare router and host intelligent types of routing methods, corresponding to various data transfer protocols. We analyze host intelligent routing as a transferable utility cooperative game with externalities. The main aim of the paper is to provide a framework in which the efficiency of various routing algorithms can be compared and the transferable utility game arising in the cooperative case can be analyzed.
Abstract: This paper presents the comparative study of coded
data methods for finding the benefit of concealing the natural data
which is the mercantile secret. Influential parameters of the number
of replicates (rep), treatment effects (τ) and standard deviation (σ)
against the efficiency of each transformation method are investigated.
The experimental data are generated via computer simulations under
the specified condition of the process with the completely
randomized design (CRD). Three ways of data transformation consist
of Box-Cox, arcsine and logit methods. The difference values of F
statistic between coded data and natural data (Fc-Fn) and hypothesis
testing results were determined. The experimental results indicate
that the Box-Cox results are significantly different from natural data
in cases of smaller levels of replicates and seem to be improper when
the parameter of minus lambda has been assigned. On the other hand,
arcsine and logit transformations are more robust and obviously,
provide more precise numerical results. In addition, the alternate
ways to select the lambda in the power transformation are also
offered to achieve much more appropriate outcomes.
Abstract: Over the years, there is a growing trend towards
quality-based specifications in highway construction. In many
Quality Control/Quality Assurance (QC/QA) specifications, the
contractor is primarily responsible for quality control of the process,
whereas the highway agency is responsible for testing the acceptance
of the product. A cooperative investigation was conducted in Illinois
over several years to develop a prototype End-Result Specification
(ERS) for asphalt pavement construction. The final characteristics of
the product are stipulated in the ERS and the contractor is given
considerable freedom in achieving those characteristics. The risk for
the contractor or agency depends on how the acceptance limits and
processes are specified. Stochastic simulation models are very useful
in estimating and analyzing payment risk in ERS systems and these
form an integral part of the Illinois-s prototype ERS system. This
paper describes the development of an innovative methodology to
estimate the variability components in in-situ density, air voids and
asphalt content data from ERS projects. The information gained from
this would be crucial in simulating these ERS projects for estimation
and analysis of payment risks associated with asphalt pavement
construction. However, these methods require at least two parties to
conduct tests on all the split samples obtained according to the
sampling scheme prescribed in present ERS implemented in Illinois.
Abstract: Multiple-input multiple-output (MIMO) systems are
widely in use to improve quality, reliability of wireless transmission
and increase the spectral efficiency. However in MIMO systems,
multiple copies of data are received after experiencing various
channel effects. The limitations on account of complexity due to
number of antennas in case of conventional decoding techniques have
been looked into. Accordingly we propose a modified sphere decoder
(MSD-1) algorithm with lower complexity and give rise to system
with high spectral efficiency. With the aim to increase signal
diversity we apply rotated quadrature amplitude modulation (QAM)
constellation in multi dimensional space. Finally, we propose a new
architecture involving space time trellis code (STTC) concatenated
with space time block code (STBC) using MSD-1 at the receiver for
improving system performance. The system gains have been verified
with channel state information (CSI) errors.
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: Knowledge and these notions have become more and
more important and we speak about a knowledge based society
today. A lot of small and big companies have reacted upon these new
challenges. But there is a deep abyss about knowledge conception
and practice between the professional researchers and company - life.
The question of this research was: How can small and mediumsized
companies be equal to the demands of new economy?
Questionnaires were used in this research and a special segment of
the native knowledge based on economy was focused on.
Researchers would have liked to know what the sources of success
are and how they can be in connection with questions of knowledge
acquisition, knowledge transfer, knowledge utilization in small and
medium-sized companies. These companies know that they have to
change their behaviour and thinking, but they are not on the suitable
level that they can compete with bigger or multinational companies.
Abstract: Visual information is very important in human perception
of surrounding world. Video is one of the most common ways to
capture visual information. The video capability has many benefits
and can be used in various applications. For the most part, the
video information is used to bring entertainment and help to relax,
moreover, it can improve the quality of life of deaf people. Visual
information is crucial for hearing impaired people, it allows them to
communicate personally, using the sign language; some parts of the
person being spoken to, are more important than others (e.g. hands,
face). Therefore, the information about visually relevant parts of the
image, allows us to design objective metric for this specific case. In
this paper, we present an example of an objective metric based on
human visual attention and detection of salient object in the observed
scene.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.
Abstract: This paper proposes a Wavelength Division
Multiplexing (WDM) technology based Storage Area Network
(SAN) for all type of Disaster recovery operation. It considers
recovery when all paths failure in the network as well as the main
SAN site failure also the all backup sites failure by the effect of
natural disasters such as earthquakes, fires and floods, power outage,
and terrorist attacks, as initially SAN were designed to work within
distance limited environments[2]. Paper also presents a NEW PATH
algorithm when path failure occurs. The simulation result and
analysis is presented for the proposed architecture with performance
consideration.
Abstract: The evaluation of energy release rate and centre Crack
Opening Displacement (COD) for circumferential Through-Wall
Cracked (TWC) pipes is an important issue in the assessment of
critical crack length for unstable fracture. The ability to predict crack
growth continues to be an important component of research for
several structural materials. Crack growth predictions can aid the
understanding of the useful life of a structural component and the
determination of inspection intervals and criteria. In this context,
studies were carried out at CSIR-SERC on Nuclear Power Plant
(NPP) piping components subjected to monotonic as well as cyclic
loading to assess the damage for crack growth due to low-cycle
fatigue in circumferentially TWC pipes.
Abstract: The research was set up on chernozem soil at the Látókép AGTC MÉK research area of the University of Debrecen in Hungary. We examined the yield, the yield production per 1kg NPK fertilizer and the water and nutrient utilization of hybrid PR37N01 and PR37M81 in 2013. We found that PR37N01 produced the most yield at the level of N120+P (17,476kg ha-1) while PR37M81 reached the highest yield at level N150+PK (16,754kg ha-1). Studies related to yield production per 1kg NPK indicated that the best results were achieved at level N30+PK compared to the control treatment. Yield production per 1kg NPK was17.6kg kg-1 by P37N01 and 44.2kg kg-1 by PR37M81. By comparing the water utilization of hybrids we found that the worst water utilization results were reached in the control treatment (PR37N01: 26.2kg mm-1, PR37M81: 19.5kg mm-1). The best water utilization values were produced at level N120+PK in the case of hybrid PR37N01 (32.1kg mm-1) and at N150+PK in the case of hybrid PR37M81 (30.8kg mm-1). We established the values of the nutrient reaction and the fertilizer optimum of hybrids. We discovered a strong relationship between the amount of fertilizer applied and the yield produced (r2= 0.8228–0.9515). The best nutrient response was induced by hybrid PR37N01, while the weakest results were reached by hybrid PR37M81.
Abstract: This paper explores the implementation of adaptive
coding and modulation schemes for Multiple-Input Multiple-Output
Orthogonal Frequency Division Multiplexing (MIMO-OFDM) feedback
systems. Adaptive coding and modulation enables robust and
spectrally-efficient transmission over time-varying channels. The basic
premise is to estimate the channel at the receiver and feed this estimate
back to the transmitter, so that the transmission scheme can be
adapted relative to the channel characteristics. Two types of codebook
based channel feedback techniques are used in this work. The longterm
and short-term CSI at the transmitter is used for efficient channel
utilization. OFDM is a powerful technique employed in communication
systems suffering from frequency selectivity. Combined with
multiple antennas at the transmitter and receiver, OFDM proves to be
robust against delay spread. Moreover, it leads to significant data rates
with improved bit error performance over links having only a single
antenna at both the transmitter and receiver. The coded modulation
increases the effective transmit power relative to uncoded variablerate
variable-power MQAM performance for MIMO-OFDM feedback
system. Hence proposed arrangement becomes an attractive approach
to achieve enhanced spectral efficiency and improved error rate
performance for next generation high speed wireless communication
systems.
Abstract: The presented work is motivated by a french law regarding nuclear waste management. In order to avoid the limitation coming with the usage of the existing scenario codes, as COSI, VISION or FAMILY, the Core Library for Advance Scenario Simulation (CLASS) is being develop. CLASS is an open source tool, which allows any user to simulate an electronuclear scenario. The main CLASS asset, is the possibility to include any type of reactor, even a complitely new concept, through the generation of its ACSII evolution database. In the present article, the CLASS working basis will be presented as well as a simple exemple in order to show his potentiel. In the considered exemple, the effect of the transmutation will be assessed on Minor Actinide Inventory produced by PWR reactors.