Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.
Abstract: The iron loss is a source of detuning in vector controlled
induction motor drives if the classical rotor vector controller is used for
decoupling. In fact, the field orientation will not be satisfied and the
output torque will not truck the reference torque mostly used by Loss
Model Controllers (LMCs). In addition, this component of loss, among
others, may be excessive if the vector controlled induction motor is
driving light loads. In this paper, the series iron loss model is used to
develop a vector controller immune to iron loss effect and then an LMC
to minimize the total power loss using the torque generated by the speed
controller.
Abstract: The paper presents an investigation in to the effect of neural network predictive control of UPFC on the transient stability performance of a multimachine power system. The proposed controller consists of a neural network model of the test system. This model is used to predict the future control inputs using the damped Gauss-Newton method which employs ‘backtracking’ as the line search method for step selection. The benchmark 2 area, 4 machine system that mimics the behavior of large power systems is taken as the test system for the study and is subjected to three phase short circuit faults at different locations over a wide range of operating conditions. The simulation results clearly establish the robustness of the proposed controller to the fault location, an increase in the critical clearing time for the circuit breakers, and an improved damping of the power oscillations as compared to the conventional PI controller.
Abstract: In this paper, a PSO-based approach is proposed to
derive a digital controller for redesigned digital systems having an interval plant based on resemblance of the extremal gain/phase
margins. By combining the interval plant and a controller as an interval system, extremal GM/PM associated with the loop transfer function
can be obtained. The design problem is then formulated as an optimization problem of an aggregated error function revealing the deviation on the extremal GM/PM between the redesigned digital
system and its continuous counterpart, and subsequently optimized by
a proposed PSO to obtain an optimal set of parameters for the digital controller. Computer simulations have shown that frequency
responses of the redesigned digital system having an interval plant bare a better resemblance to its continuous-time counter part by the incorporation of a PSO-derived digital controller in comparison to those obtained using existing open-loop discretization methods.
Abstract: This paper presents the idea of a rough controller with application to control the overhead traveling crane system. The structure of such a controller is based on a suggested concept of a fuzzy logic controller. A measure of fuzziness in rough sets is introduced. A comparison between fuzzy logic controller and rough controller has been demonstrated. The results of a simulation comparing the performance of both controllers are shown. From these results we infer that the performance of the proposed rough controller is satisfactory.
Abstract: The main objective of this project is to build an
autonomous microcontroller-based mobile robot for a local robot
soccer competition. The black competition field is equipped with
white lines to serve as the guidance path for competing robots. Two
prototypes of soccer robot embedded with the Basic Stamp II
microcontroller have been developed. Two servo motors are used as
the drive train for the first prototype whereas the second prototype
uses two DC motors as its drive train. To sense the lines, lightdependent
resistors (LDRs) supply the analog inputs for the
microcontroller. The performances of both prototypes are evaluated.
The DC motor-driven robot has produced better trajectory control
over the one using servo motors and has brought the team into the
final round.
Abstract: Attitude control of aerospace system with liquid containers may face to a problem associate with fuel sloshing. The sloshing phenomena can degrade the stability of control system and in the worst case, interaction between the attitude control system and fuel vibration leading to resonance. In this paper, a full process of nonlinear dynamic modeling of an aerospace launch vehicle with fuel sloshing is given. Then, a new control system based on model reference adaptive filter is proposed and its algorithm is extracted. This controller implemented on the main attitude control system. Finally, numerical simulation of nonlinear model and control system is carried out to examine the performance of the new controller. Results of simulations show that the inconvenient effects of the fuel sloshing by augmenting this control system are reduced and attitude control system performs, satisfactorily.
Abstract: Microwave energy can be used for drying purpose. It is unique process. It is distinctly different from conventional drying process. It is advantageous over conventional drying / heating processes. When microwave energy is used for drying purpose, the process can be accelerated with a better control to achieve uniform heating, more conversion efficiency, selective drying and ultimately improved product quality of the output. Also, less floor space and compact system are the added advantages. Existing low power microwave drying system is to be modified with suitable applicator. Appropriate sensors are to be used to measure parameters like moisture, temperature, weight of sample. Suitable high tech controller is to be used to control microwave power continuously from minimum to maximum. Phase - controller, cycle - controller and PWM - controller are some of the advanced power control techniques. It has been proposed to work on turmeric using high-tech phase controller to control the microwave power conveniently. The drying of turmeric with microwave energy employing phase controller gives better results as formulated in this paper and hence new approach of processing turmeric will open future doors of profit making to allied industries and the farmers.
Abstract: In this paper, Neuro-Fuzzy based Fuzzy Subtractive
Clustering Method (FSCM) and Self Tuning Fuzzy PD-like
Controller (STFPDC) were used to solve non-linearity and trajectory
problems of pitch AND yaw angles of Twin Rotor MIMO system
(TRMS). The control objective is to make the beams of TRMS reach
a desired position quickly and accurately. The proposed method
could achieve control objectives with simpler controller. To simplify
the complexity of STFPDC, ANFIS based FSCM was used to
simplify the controller and improve the response. The proposed
controllers could achieve satisfactory objectives under different input
signals. Simulation results under MATLAB/Simulink® proved the
improvement of response and superiority of simplified STFPDC on
Fuzzy Logic Controller (FLC).
Abstract: The approach proposed here is oriented in the direction of fuzzy system for the analysis and the synthesis of intelligent climate controllers, the simulation of the internal climate of the greenhouse is achieved by a linear model whose coefficients are obtained by identification. The use of fuzzy logic controllers for the regulation of climate variables represents a powerful way to minimize the energy cost. Strategies of reduction and optimization are adopted to facilitate the tuning and to reduce the complexity of the controller.
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.
Abstract: This paper features the mathematical modeling of a single input single output based Timoshenko smart beam. Further, this mathematical model is used to design a multirate output feedback based discrete sliding mode controller using Bartoszewicz law to suppress the flexural vibrations. The first 2 dominant vibratory modes is retained. Here, an application of the discrete sliding mode control in smart systems is presented. The algorithm uses a fast output sampling based sliding mode control strategy that would avoid the use of switching in the control input and hence avoids chattering. This method does not need the measurement of the system states for feedback as it makes use of only the output samples for designing the controller. Thus, this methodology is more practical and easy to implement.
Abstract: This paper presents a novel approach for tuning unified power flow controller (UPFC) based damping controller in order to enhance the damping of power system low frequency oscillations. The design problem of damping controller is formulated as an optimization problem according to the eigenvalue-based objective function which is solved using iteration particle swarm optimization (IPSO). The effectiveness of the proposed controller is demonstrated through eigenvalue analysis and nonlinear time-domain simulation studies under a wide range of loading conditions. The simulation study shows that the designed controller by IPSO performs better than CPSO in finding the solution. Moreover, the system performance analysis under different operating conditions show that the δE based controller is superior to the mB based controller.
Abstract: It is well known that a linear dynamic system including
a delay will exhibit limit cycle oscillations when a bang-bang sensor
is used in the feedback loop of a PID controller. A similar behaviour
occurs when a delayed feedback signal is used to train a neural
network. This paper develops a method of predicting this behaviour
by linearizing the system, which can be shown to behave in a manner
similar to an integral controller. Using this procedure, it is possible
to predict the characteristics of the neural network driven limit cycle
to varying degrees of accuracy, depending on the information known
about the system. An application is also presented: the intelligent
control of a spark ignition engine.
Abstract: The object of this paper is to design and analyze a
proportional – integral (PI) control for positive output elementary
super lift Luo converter (POESLLC), which is the start-of-the-art
DC-DC converter. The positive output elementary super lift Luo
converter performs the voltage conversion from positive source
voltage to positive load voltage. This paper proposes a
development of PI control capable of providing the good static and
dynamic performance compared to proportional – integralderivative
(PID) controller. Using state space average method
derives the dynamic equations describing the positive output
elementary super lift luo converter and PI control is designed. The
simulation model of the positive output elementary super lift Luo
converter with its control circuit is implemented in
Matlab/Simulink. The PI control for positive output elementary
super lift Luo converter is tested for transient region, line changes,
load changes, steady state region and also for components
variations.
Abstract: In this paper, we present an experimental testing for
a new algorithm that determines an optimal controller-s coefficients
for output variance reduction related to Linear Time Invariant (LTI)
Systems. The algorithm features simplicity in calculation, generalization
to minimal and non-minimal phase systems, and could be
configured to achieve reference tracking as well as variance reduction
after compromising with the output variance. An experiment of DCmotor
velocity control demonstrates the application of this new
algorithm in designing the controller. The results show that the
controller achieves minimum variance and reference tracking for a
preset velocity reference relying on an identified model of the motor.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: This paper introduces a new digital logic design, which
combines the DSP and FPGA to implement the conventional DTC of
induction machine. The DSP will be used for floating point
calculation whereas the FPGA main task is to implement the
hysteresis-based controller. The emphasis is on FPGA digital logic
design. The simulation and experimental results are presented and
summarized.
Abstract: This paper presents a new method for the
implementation of a direct rotor flux control (DRFOC) of induction
motor (IM) drives. It is based on the rotor flux components
regulation. The d and q axis rotor flux components feed proportional
integral (PI) controllers. The outputs of which are the target stator
voltages (vdsref and vqsref). While, the synchronous speed is depicted at
the output of rotor speed controller. In order to accomplish variable
speed operation, conventional PI like controller is commonly used.
These controllers provide limited good performances over a wide
range of operations even under ideal field oriented conditions. An
alternate approach is to use the so called fuzzy logic controller. The
overall investigated system is implemented using dSpace system
based on digital signal processor (DSP). Simulation and experimental
results have been presented for a one kw IM drives to confirm the
validity of the proposed algorithms.
Abstract: this paper presents a novel neural network controller
with composite adaptation low to improve the trajectory tracking
problems of biped robots comparing with classical controller. The
biped model has 5_link and 6 degrees of freedom and actuated by
Plated Pneumatic Artificial Muscle, which have a very high power to
weight ratio and it has large stoke compared to similar actuators. The
proposed controller employ a stable neural network in to approximate
unknown nonlinear functions in the robot dynamics, thereby
overcoming some limitation of conventional controllers such as PD
or adaptive controllers and guarantee good performance. This NN
controller significantly improve the accuracy requirements by
retraining the basic PD/PID loop, but adding an inner adaptive loop
that allows the controller to learn unknown parameters such as
friction coefficient, therefore improving tracking accuracy.
Simulation results plus graphical simulation in virtual reality show
that NN controller tracking performance is considerably better than
PD controller tracking performance.