Abstract: At very high speeds, bubbles form in the underwater vehicles because of sharp trailing edges or of places where the local pressure is lower than the vapor pressure. These bubbles are called cavities and the size of the cavities grows as the velocity increases. A properly designed cavitator can induce the formation of a single big cavity all over the vehicle. Such a vehicle travelling in the vaporous cavity is called a supercavitating vehicle and the present research work mainly focuses on the dynamic modeling of such vehicles. Cavitation of the fins is also accounted and the effect of the same on trajectory is well explained. The entire dynamics has been developed using the state space approach and emphasis is given on the effect of size and angle of attack of the cavitator. Control law has been established for the motion of the vehicle using Non-linear Dynamic Inverse (NDI) with cavitator as the control surface.
Abstract: Unsteady natural convection and heat transfer in a square cavity partially filled with porous media using a thermal
non-equilibrium model is studied in this paper. The left vertical wall is
maintained at a constant hot temperature Th and the right vertical wall
is maintained at a constant cold temperature Tc, while the horizontal
walls are adiabatic. The governing equations are obtained by applying
the Darcy model and Boussinesq approximation. COMSOL’s finite
element method is used to solve the non-dimensional governing
equations together with specified boundary conditions. The governing
parameters of this study are the Rayleigh number (Ra = 10^5, and Ra = 10^6 ), Darcy namber (Da = 10^−2, and Da = 10^−3),
the modified thermal conductivity ratio (10^−1 ≤ γ ≤ 10^4), the inter-phase heat transfer coefficien (10^−1 ≤ H ≤ 10^3) and the
time dependent (0.001 ≤ τ ≤ 0.2). The results presented for
values of the governing parameters in terms of streamlines in both
fluid/porous-layer, isotherms of fluid in fluid/porous-layer, isotherms
of solid in porous layer, and average Nusselt number.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: The effect of the blade tip geometry of a high pressure
gas turbine is studied experimentally and computationally for high
speed leakage flows. For this purpose two simplified models are
constructed, one models a flat tip of the blade and the second models
a cavity tip of the blade. Experimental results are obtained from a
transonic wind tunnel to show the static pressure distribution along
the tip wall and provide flow visualization. RANS computations
were carried to provide further insight into the mean flow behavior
and to calculate the discharge coefficient which is a measure of the
flow leaking over the tip. It is shown that in both geometries of tip
the flow separates over the tip to form a separation bubble. The
bubble is higher for the cavity tip while a complete shock wave
system of oblique waves ending with a normal wave can be seen for
the flat tip. The discharge coefficient for the flat tip shows less
dependence on the pressure ratio over the blade tip than the cavity
tip. However, the discharge coefficient for the cavity tip is lower than
that of the flat tip, showing a better ability to reduce the leakage flow
and thus increase the turbine efficiency.
Abstract: Injection forging is a Nett-shape manufacturing
process in which one or two punches move axially causing a radial
flow into a die cavity in a form which is prescribed by the exitgeometry,
such as pulley, flanges, gears and splines on a shaft. This
paper presents an experimental and numerical study of the injection
forging of splines in terms of load requirement and material flow.
Three dimensional finite element analyses are used to investigate the
effect of some important parameters in this process. The experiment
has been carried out using solid commercial lead billets with two
different billet diameters and four different dies.
Abstract: The paper provides a numerical investigation of the
entropy generation analysis due to natural convection in an inclined
square porous cavity. The coupled equations of mass, momentum,
energy and species conservation are solved using the Control Volume
Finite-Element Method. Effect of medium permeability and
inclination angle on entropy generation is analysed. It was found that
according to the Darcy number and the porous thermal Raleigh
number values, the entropy generation could be mainly due to heat
transfer or to fluid friction irreversibility and that entropy generation
reaches extremum values for specific inclination angles.
Abstract: We numerically study the three-dimensional
magnetohydrodynamics (MHD) stability of oscillatory natural
convection flow in a rectangular cavity, with free top surface, filled
with a liquid metal, having an aspect ratio equal to A=L/H=5, and
subjected to a transversal temperature gradient and a uniform
magnetic field oriented in x and z directions. The finite volume
method was used in order to solve the equations of continuity,
momentum, energy, and potential. The stability diagram obtained in
this study highlights the dependence of the critical value of the
Grashof number Grcrit , with the increase of the Hartmann number
Ha for two orientations of the magnetic field. This study confirms
the possibility of stabilization of a liquid metal flow in natural
convection by application of a magnetic field and shows that the
flow stability is more important when the direction of magnetic field
is longitudinal than when the direction is transversal.
Abstract: This paper deals with the experimental investigations
of the in-cylinder tumble flows in an unfired internal combustion
engine with a flat piston at the engine speeds ranging from 400 to
1000 rev/min., and also with the dome and dome-cavity pistons at an
engine speed of 1000 rev/min., using particle image velocimetry.
From the two-dimensional in-cylinder flow measurements, tumble
flow analysis is carried out in the combustion space on a vertical
plane passing through cylinder axis. To analyze the tumble flows,
ensemble average velocity vectors are used and to characterize it,
tumble ratio is estimated. From the results, generally, we have found
that tumble ratio varies mainly with crank angle position. Also, at the
end of compression stroke, average turbulent kinetic energy is more
at higher engine speeds. We have also found that, at 330 crank angle
position, flat piston shows an improvement of about 85 and 23% in
tumble ratio, and about 24 and 2.5% in average turbulent kinetic
energy compared to dome and dome-cavity pistons respectively
Abstract: We developed a new method based on quasimolecular
modeling to simulate the cavity flow in three cavity
shapes: rectangular, half-circular and bucket beer in cgs units. Each
quasi-molecule was a group of particles that interacted in a fashion
entirely analogous to classical Newtonian molecular interactions.
When a cavity flow was simulated, the instantaneous velocity vector
fields were obtained by using an inverse distance weighted
interpolation method. In all three cavity shapes, fluid motion was
rotated counter-clockwise. The velocity vector fields of the three
cavity shapes showed a primary vortex located near the upstream
corners at time t ~ 0.500 s, t ~ 0.450 s and t ~ 0.350 s, respectively.
The configurational kinetic energy of the cavities increased as time
increased until the kinetic energy reached a maximum at time t ~
0.02 s and, then, the kinetic energy decreased as time increased. The
rectangular cavity system showed the lowest kinetic energy, while
the half-circular cavity system showed the highest kinetic energy.
The kinetic energy of rectangular, beer bucket and half-circular
cavities fluctuated about stable average values 35.62 x 103, 38.04 x
103 and 40.80 x 103 ergs/particle, respectively. This indicated that the
half-circular shapes were the most suitable shape for a shrimp pond
because the water in shrimp pond flows best when we compared with
rectangular and beer bucket shape.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: In the present study, the lattice Boltzmann Method (LBM) is applied for simulating of Natural Convection in an inclined open ended cavity. The cavity horizontal walls are insulated while the west wall is maintained at a uniform temperature higher than the ambient. Prandtl number is fixed to 0.71 (air) while Rayligh numbers, aspect ratio of the cavity are changed in the range of 103 to 104 and of 1-4, respectively. The numerical code is validated for the previously results for open ended cavities, and then the results of an inclined open ended cavity for various angles of rotating open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number on hot wall decreases for all rotation angles. When gravity acceleration direction is opposite of standard gravity direction the convection heat transfer has a manner same as conduction.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: The three-dimensional incompressible flow past a
rectangular open cavity is investigated, where the aspect ratio of the
cavity is considered as 4. The principle objective is to use large-eddy
simulation to resolve and control the large-scale structures, which are
largely responsible for flow oscillations in a cavity. The flow past an
open cavity is very common in aerospace applications and can be a
cause of acoustic source due to hydrodynamic instability of the shear
layer and its interactions with the downstream edge. The unsteady
Navier-stokes equations have been solved on a staggered mesh using
a symmetry-preserving central difference scheme. Synthetic jet has
been used as an active control to suppress the cavity oscillations in
wake mode for a Reynolds number of ReD = 3360. The effect of
synthetic jet has been studied by varying the jet amplitude and
frequency, which is placed at the upstream wall of the cavity. The
study indicates that there exits a frequency band, which is larger than
a critical value, is effective in attenuating cavity oscillations when
blowing ratio is more than 1.0.
Abstract: We present a Large-Eddy simulation of a vortex cell
with circular shaped. The results show that the flow field can be sub
divided into four important zones, the shear layer above the cavity,
the stagnation zone, the vortex core in the cavity and the boundary
layer along the wall of the cavity. It is shown that the vortex core
consits of solid body rotation without much turbulence activity. The
vortex is mainly driven by high energy packets that are driven into the
cavity from the stagnation point region and by entrainment of fluid
from the cavity into the shear layer. The physics in the boundary
layer along the cavity-s wall seems to be far from that of a canonical
boundary layer which might be a crucial point for modelling this
flow.
Abstract: In this article an isotropic linear elastic half-space with
a cylindrical cavity of finite length is considered to be under the
effect of a ring shape time-harmonic torsion force applied at an
arbitrary depth on the surface of the cavity. The equation of
equilibrium has been written in a cylindrical coordinate system. By
means of Fourier cosine integral transform, the non-zero
displacement component is obtained in the transformed domain. With
the aid of the inversion theorem of the Fourier cosine integral
transform, the displacement is obtained in the real domain. With the
aid of boundary conditions, the involved boundary value problem for
the fundamental solution is reduced to a generalized Cauchy singular
integral equation. Integral representation of the stress and
displacement are obtained, and it is shown that their degenerated
form to the static problem coincides with existing solutions in the
literature.
Abstract: A high energy dual-wavelength extracavity KTA
optical parametric oscillator (OPO) with excellent stability and beam
quality, which is pumped by a Q-switched single-longitudinal-mode
Nd:YAG laser, has been demonstrated based on a type II noncritical
phase matching (NCPM) KTA crystal. The maximum pulse energy of
10.2 mJ with the output stability of better than 4.1% rms at 3.467 μm is
obtained at the repetition rate of 10 Hz and pulse width of 2 ns, and the
11.9 mJ of 1.535 μm radiation is obtained simultaneously. This
extracavity NCPM KTA OPO is very useful when high energy, high
beam quality and smooth time domain are needed.
Abstract: Double-diffusive natural convection in an open top
square cavity and heated from the side is studied numerically.
Constant temperatures and concentration are imposed along the right
and left walls while the heat balance at the surface is assumed to obey
Newton-s law of cooling. The finite difference method is used to
solve the dimensionless governing equations. The numerical results
are reported for the effect of Marangoni number, Biot number and
Prandtl number on the contours of streamlines, temperature and
concentration. The predicted results for the average Nusselt number
and Sherwood number are presented for various parametric
conditions. The parameters involved are as follows; the thermal
Marangoni number, 0 ≤ MaT ≤1000 , the solutal Marangoni number,
0 1000 c ≤ Ma ≤ , the Biot number, 0 ≤ Bi ≤ 6 , Grashof number,
5 Gr = 10 and aspect ratio 1. The study focused on both flows; thermal
dominated, N = 0.8 , and compositional dominated, N = 1.3 .
Abstract: Double-diffusive steady convection in a partially
porous cavity with partially permeable walls and under the combined
buoyancy effects of thermal and mass diffusion was analysed
numerically using finite volume method.
The top wall is well insulated and impermeable while the bottom
surface is partially well insulated and impermeable and partially
submitted to constant temperature T1 and concentration C1. Constant
equal temperature T2 and concentration C2 are imposed along the
vertical surfaces of the enclosure. Mass suction/injection and
injection/suction are respectively considered at the bottom of the
porous centred partition and at one of the vertical walls.
Heat and mass transfer characteristics as streamlines and average
Nusselt numbers and Sherwood numbers were discussed for different
values of buoyancy ratio, Rayleigh number, and injection/suction
coefficient.
It is especially noted that increasing the injection factor
disadvantages the exchanges in the case of the injection while the
transfer is augmented in case of suction. On the other hand, a critical
value of the buoyancy ratio was highlighted for which heat and mass
transfers are minimized.
Abstract: Since 2005, an SRF module of CESR type serves as the
accelerating cavity at the Taiwan Light Source in the National
Synchrotron Radiation Research Center. A 500-MHz niobium cavity
is immersed in liquid helium inside this SRF module. To reduce heat
load, the liquid helium vessel is thermally shielded by
liquid-nitrogen-cooled copper layer, and the beam chambers are also
anchored with pipes of the liquid nitrogen flow in middle of the liquid
helium vessel and the vacuum vessel. A strong correlation of the
movement of the cavity-s frequency tuner with the temperature
variation of parts cooled with liquid nitrogen was observed. A
previous study on a spare SRF module with the niobium cavity cooled
by liquid nitrogen instead of liquid helium, satisfactory suppression of
the thermal oscillation was achieved by attaching a temporary buffer
tank for the vented shielding nitrogen flow from the SRF module. In
this study, a home-made buffer tank is designed and integrated to the
spare SRF module with cavity cooled by liquid helium. Design,
construction, integration, and preliminary test results of this buffer
tank are presented.
Abstract: In the literature of fuzzy measures, there exist many
well known parametric and non-parametric measures, each with its
own merits and limitations. But our main emphasis is on
applications of these measures to a variety of disciplines. To extend
the scope of applications of these fuzzy measures to geometry, we
need some special fuzzy measures. In this communication, we have
introduced two new fuzzy measures involving trigonometric
functions and simultaneously provided their applications to obtain
the basic results already existing in the literature of geometry.