Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: This paper presents a numerical analysis of the
performance of a five-bladed Darrieus vertical-axis water turbine,
based on the NACA 0025 blade profile, for both bare and shrouded
configurations. A complete campaign of 2-D simulations, performed
for several values of tip speed ratio and based on RANS unsteady
calculations, has been performed to obtain the rotor torque and power
curves. Also the effect of a NACA-shaped central hydrofoil has been
investigated, with the aim of evaluating the impact of a solid
blockage on the performance of the shrouded rotor configuration.
The beneficial effect of the shroud on rotor overall performances
has clearly been evidenced, while the adoption of the central
hydrofoil has proved to be detrimental, being the resulting flow slow
down (due to the presence of the obstacle) much higher with respect
to the flow acceleration (due to the solid blockage effect).
Abstract: Modelling techniques for a fluid coupling taken from
published literature have been extended to include the effects of the
filling and emptying of the coupling with oil and the variation in
losses when the coupling is partially full. In the model, the fluid flow
inside the coupling is considered to have two principal velocity
components; one circumferentially about the coupling axis
(centrifugal head) and the other representing the secondary vortex
within the coupling itself (vortex head). The calculation of liquid
mass flow rate circulating between the two halves of the coupling is
based on: the assumption of a linear velocity variation in the
circulating vortex flow; the head differential in the fluid due to the
speed difference between the two shafts; and the losses in the
circulating vortex flow as a result of the impingement of the flow
with the blades in the coupling and friction within the passages
between the blades.
Abstract: A data cutting and sorting method (DCSM) is proposed
to optimize the performance of data mining. DCSM reduces the
calculation time by getting rid of redundant data during the data
mining process. In addition, DCSM minimizes the computational units
by splitting the database and by sorting data with support counts. In the
process of searching for the relationship between metabolic syndrome
and lifestyles with the health examination database of an electronics
manufacturing company, DCSM demonstrates higher search
efficiency than the traditional Apriori algorithm in tests with different
support counts.
Abstract: Documents clustering become an essential technology
with the popularity of the Internet. That also means that fast and
high-quality document clustering technique play core topics. Text
clustering or shortly clustering is about discovering semantically
related groups in an unstructured collection of documents. Clustering
has been very popular for a long time because it provides unique
ways of digesting and generalizing large amounts of information.
One of the issues of clustering is to extract proper feature (concept)
of a problem domain. The existing clustering technology mainly
focuses on term weight calculation. To achieve more accurate
document clustering, more informative features including concept
weight are important. Feature Selection is important for clustering
process because some of the irrelevant or redundant feature may
misguide the clustering results. To counteract this issue, the proposed
system presents the concept weight for text clustering system
developed based on a k-means algorithm in accordance with the
principles of ontology so that the important of words of a cluster can
be identified by the weight values. To a certain extent, it has resolved
the semantic problem in specific areas.
Abstract: The paper presents a simple and an accurate formula
that has been developed for the conduction angle (δ) of a single
phase half-wave or full-wave controlled rectifier with RL load. This
formula can be also used for calculating the conduction angle (δ) in
case of A.C. voltage regulator with inductive load under
discontinuous current mode. The simulation results shows that the
conduction angle calculated from the developed formula agree very
well with that obtained from the exact solution arrived from the
iterative method. Applying the developed formula can reduce the
computational time and reduce the time for manual classroom
calculation. In addition, the proposed formula is attractive for real
time implementations.
Abstract: This research aims to analyze the regenerative burner and the recuperative burner for the different reheating furnaces in the steel industry. The warm air temperatures of the burners are determined to suit with the sizes of the reheating furnaces by considering the air temperature, the fuel cost and the investment cost. The calculations of the payback period and the net present value are studied to compare the burners for the different reheating furnaces. The energy balance is utilized to calculate and compare the energy used in the different sizes of reheating furnaces for each burner. It is found that the warm air temperature is different if the sizes of reheating furnaces are varied. Based on the considerations of the net present value and the payback period, the regenerative burner is suitable for all plants at the same life of the burner. Finally, the sensitivity analysis of all factors has been discussed in this research.
Abstract: This paper presents application artificial intelligent (AI) techniques, namely artificial neural network (ANN), adaptive neuro fuzzy interface system (ANFIS), to estimate the real power transfer between generators and loads. Since these AI techniques adopt supervised learning, it first uses modified nodal equation method (MNE) to determine real power contribution from each generator to loads. Then the results of MNE method and load flow information are utilized to estimate the power transfer using AI techniques. The 25-bus equivalent system of south Malaysia is utilized as a test system to illustrate the effectiveness of both AI methods compared to that of the MNE method. The mean squared error of the estimate of ANN and ANFIS power transfer allocation methods are 1.19E-05 and 2.97E-05, respectively. Furthermore, when compared to MNE method, ANN and ANFIS methods computes generator contribution to loads within 20.99 and 39.37msec respectively whereas the MNE method took 360msec for the calculation of same real power transfer allocation.
Abstract: This paper presents a means for reducing the torque
variation during the revolution of a vertical-axis water turbine
(VAWaterT) by increasing the blade number. For this purpose, twodimensional
CFD analyses have been performed on a straight-bladed
Darrieus-type rotor. After describing the computational model and
the relative validation procedure, a complete campaign of
simulations, based on full RANS unsteady calculations, is proposed
for a three, four and five-bladed rotor architectures, characterized by
a NACA 0025 airfoil. For each proposed rotor configuration, flow
field characteristics are investigated at several values of tip speed
ratio, allowing a quantification of the influence of blade number on
flow geometric features and dynamic quantities, such as rotor torque
and power. Finally, torque and power curves are compared for the
three analyzed architectures, achieving a quantification of the effect
of blade number on overall rotor performance.
Abstract: Many recent high energy physics calculations
involving charm and beauty invoke wave function at the origin
(WFO) for the meson bound state. Uncertainties of charm and beauty
quark masses and different models for potentials governing these
bound states require a simple numerical algorithm for evaluation of
the WFO's for these bound states. We present a simple algorithm for
this propose which provides WFO's with high precision compared
with similar ones already obtained in the literature.
Abstract: Camera calibration is an indispensable step for augmented
reality or image guided applications where quantitative information
should be derived from the images. Usually, a camera
calibration is obtained by taking images of a special calibration object
and extracting the image coordinates of projected calibration marks
enabling the calculation of the projection from the 3d world coordinates
to the 2d image coordinates. Thus such a procedure exhibits
typical steps, including feature point localization in the acquired
images, camera model fitting, correction of distortion introduced by
the optics and finally an optimization of the model-s parameters. In
this paper we propose to extend this list by further step concerning
the identification of the optimal subset of images yielding the smallest
overall calibration error. For this, we present a Monte Carlo based
algorithm along with a deterministic extension that automatically
determines the images yielding an optimal calibration. Finally, we
present results proving that the calibration can be significantly
improved by automated image selection.
Abstract: Quality control charts indicate out of control
conditions if any nonrandom pattern of the points is observed or any
point is plotted beyond the control limits. Nonrandom patterns of
Shewhart control charts are tested with sensitizing rules. When the
processes are defined with fuzzy set theory, traditional sensitizing
rules are insufficient for defining all out of control conditions. This is
due to the fact that fuzzy numbers increase the number of out of
control conditions. The purpose of the study is to develop a set of
fuzzy sensitizing rules, which increase the flexibility and sensitivity
of fuzzy control charts. Fuzzy sensitizing rules simplify the
identification of out of control situations that results in a decrease in
the calculation time and number of evaluations in fuzzy control chart
approach.
Abstract: KREISIG is a computer simulation program, firstly developed by Munawar (1994) in Germany to optimize signalized roundabout. The traffic movement is based on the car following theory. Turbine method has been implemented for signal setting. The program has then been further developed in Indonesia to meet the traffic characteristics in Indonesia by adjusting the sensitivity of the drivers. Trial and error method has been implemented to adjust the saturation flow. The saturation flow output has also been compared to the calculation method according to 1997 Indonesian Highway Capacity Manual. It has then been implemented to optimize signalized roundabout at Kleringan roundabout in Malioboro area, Yogyakarta, Indonesia. It is found that this method can optimize the signal setting of this roundabout. Therefore, it is recommended to use this program to optimize signalized roundabout.
Abstract: In order to research Internet quantificationally and
better model the performance of network, this paper proposes a novel
AS level network performance model (MNPM), it takes autonomous
system (AS) as basic modeling unit, measures E2E performance
between any two outdegrees of an AS and organizes measurement
results into matrix form which called performance matrix (PM).
Inter-AS performance calculation is defined according to performance
information stored in PM. Simulation has been implemented to verify
the correctness of MNPM and a practical application of MNPM
(network congestion detection) is given.
Abstract: The production of a plant can be measured in terms of
seeds. The generation of seeds plays a critical role in our social and
daily life. The fruit production which generates seeds, depends on the
various parameters of the plant, such as shoot length, leaf number,
root length, root number, etc When the plant is growing, some leaves
may be lost and some new leaves may appear. It is very difficult to
use the number of leaves of the tree to calculate the growth of the
plant.. It is also cumbersome to measure the number of roots and
length of growth of root in several time instances continuously after
certain initial period of time, because roots grow deeper and deeper
under ground in course of time. On the contrary, the shoot length of
the tree grows in course of time which can be measured in different
time instances. So the growth of the plant can be measured using the
data of shoot length which are measured at different time instances
after plantation. The environmental parameters like temperature, rain
fall, humidity and pollution are also play some role in production of
yield. The soil, crop and distance management are taken care to
produce maximum amount of yields of plant. The data of the growth
of shoot length of some mustard plant at the initial stage (7,14,21 &
28 days after plantation) is available from the statistical survey by a
group of scientists under the supervision of Prof. Dilip De. In this
paper, initial shoot length of Ken( one type of mustard plant) has
been used as an initial data. The statistical models, the methods of
fuzzy logic and neural network have been tested on this mustard
plant and based on error analysis (calculation of average error) that
model with minimum error has been selected and can be used for the
assessment of shoot length at maturity. Finally, all these methods
have been tested with other type of mustard plants and the particular
soft computing model with the minimum error of all types has been
selected for calculating the predicted data of growth of shoot length.
The shoot length at the stage of maturity of all types of mustard
plants has been calculated using the statistical method on the
predicted data of shoot length.
Abstract: The paper presents a technique suitable in robot
vision applications where it is not possible to establish the object position from one view. Usually, one view pose calculation methods
are based on the correspondence of image features established at a
training step and exactly the same image features extracted at the
execution step, for a different object pose. When such a
correspondence is not feasible because of the lack of specific features
a new method is proposed. In the first step the method computes
from two views the 3D pose of feature points. Subsequently, using a
registration algorithm, the set of 3D feature points extracted at the execution phase is aligned with the set of 3D feature points extracted
at the training phase. The result is a Euclidean transform which have
to be used by robot head for reorientation at execution step.
Abstract: Installation of power compensation equipment in
some cases places additional buses into the system. Therefore, a total
number of power flow equations and voltage unknowns increase due
to additional locations of installed devices. In this circumstance, power flow calculation is more complicated. It may result in a
computational convergence problem. This paper presents a power flow calculation by using Newton-Raphson iterative method together
with the proposed load transfer technique. This concept is to eliminate additional buses by transferring installed loads at the new buses to existing two adjacent buses. Thus, the total number of power
flow equations is not changed. The overall computational speed is
expectedly shorter than that of solving the problem without applying the load transfer technique. A 15-bus test system is employed for test
to evaluate the effectiveness of the proposed load transfer technique. As a result, the total number of iteration required and execution time
is significantly reduced.
Abstract: Environment-assisted cracking (EAC) is one of the most serious causes of structural failure over a broad range of industrial applications including offshore structures. In EAC condition there is not a definite relation such as Paris equation in Linear Elastic Fracture Mechanics (LEFM). According to studying and searching a lot what the researchers said either a material has contact with hydrogen or any other corrosive environment, phenomenon of electrical and chemical reactions of material with its environment will be happened. In the literature, there are many different works to consider fatigue crack growing and solve it but they are experimental works. Thus, in this paper, authors have an aim to evaluate mathematically the pervious works in LEFM. Obviously, if an environment is more sour and corrosive, the changes of stress intensity factor is more and the calculation of stress intensity factor is difficult. A mathematical relation to deal with the stress intensity factor during the diffusion of sour environment especially hydrogen in a marine pipeline is presented. By using this relation having and some experimental relation an analytical formulation will be presented which enables the fatigue crack growth and critical crack length under cyclic loading to be predicted. In addition, we can calculate KSCC and stress intensity factor in the pipeline caused by EAC.
Abstract: The most common result of analysis of highthroughput
data in molecular biology represents a global list of
genes, ranked accordingly to a certain score. The score can be a
measure of differential expression. Recent work proposed a new
method for selecting a number of genes in a ranked gene list from
microarray gene expression data such that this set forms the
Optimally Functionally Enriched Network (OFTEN), formed by
known physical interactions between genes or their products. Here
we present calculation results of relative connectivity of genes from
META-OFTEN network and tentative biological interpretation of the
most reproducible signal. The relative connectivity and
inbetweenness values of genes from META-OFTEN network were
estimated.