Abstract: In this paper, a methodology of a model based on
predicting the tool forces oblique machining are introduced by
adopting the orthogonal technique. The applied analytical calculation
is mostly based on Devries model and some parts of the methodology
are employed from Amareggo-Brown model. Model validation is
performed by comparing experimental data with the prediction results
on machining titanium alloy (Ti-6Al-4V) based on micro-cutting tool
perspective. Good agreements with the experiments are observed. A
detailed friction form that affected the tool forces also been examined
with reasonable results obtained.
Abstract: In this paper, the signal transmission analysis of the
semicircle-shaped via structure for the differential pairs is presented in
the frequency range up to 10 GHz. In order to improve the signal
transmission properties in the differential pairs, single via is separated
centrally into two semicircle-shaped sections, which are
interconnected with the traces of differential pairs respectively. This
via structure make possible to route differential pairs using only one
via. In addition, it can improve impedance discontinuity around its
region and then enhance the signal transmission properties in the
differential pairs. The electrical analysis such as S-parameter
calculation and eye diagram simulation has been performed to
investigate the improvement of the signal transmission property in the
differential pairs with new via structure.
Abstract: Random Forests are a powerful classification technique, consisting of a collection of decision trees. One useful feature of Random Forests is the ability to determine the importance of each variable in predicting the outcome. This is done by permuting each variable and computing the change in prediction accuracy before and after the permutation. This variable importance calculation is similar to a one-factor-at a time experiment and therefore is inefficient. In this paper, we use a regular fractional factorial design to determine which variables to permute. Based on the results of the trials in the experiment, we calculate the individual importance of the variables, with improved precision over the standard method. The method is illustrated with a study of student attrition at Monash University.
Abstract: The objective of this paper is to analyze the
performance of a double-sided axial flux permanent magnet
brushless DC (AFPM BLDC) motor with two-phase winding.
To study the motor operation, a mathematical dynamic model
has been proposed for motor, which became the basis for
simulations that were performed using MATLAB/SIMULINK
software package. The results of simulations were presented
in form of the waveforms of selected quantities and the
electromechanical characteristics performed by the motor. The
calculation results show that the two-phase motor version
develops smooth torque and reaches high efficiency. The twophase
motor can be applied where more smooth torque is
required. Finally a study on the influence of switching angle
on motor performance shows that when advance switching
technique is used, the motor operates with the highest
efficiency.
Abstract: This paper examines many mathematical methods for
molding the hourly price forward curve (HPFC); the model will be
constructed by numerous regression methods, like polynomial
regression, radial basic function neural networks & a furrier series.
Examination the models goodness of fit will be done by means of
statistical & graphical tools. The criteria for choosing the model will
depend on minimize the Root Mean Squared Error (RMSE), using the
correlation analysis approach for the regression analysis the optimal
model will be distinct, which are robust against model
misspecification. Learning & supervision technique employed to
determine the form of the optimal parameters corresponding to each
measure of overall loss. By using all the numerical methods that
mentioned previously; the explicit expressions for the optimal model
derived and the optimal designs will be implemented.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: This article presents the analysis of experimental values regarding cracking pattern, specific strains and deformability for reinforced high strength concrete beams. The beams have the concrete class C80/95 and a longitudinal reinforcement ratio of 2.01%, respectively 3.39%. The elements were subjected to flexure under static short-term and long-term loading. The experimental values are compared with calculation values using the design relationships according to Eurocode 2.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: A one-step conservative level set method, combined with a global mass correction method, is developed in this study to simulate the incompressible two-phase flows. The present framework do not need to solve the conservative level set scheme at two separated steps, and the global mass can be exactly conserved. The present method is then more efficient than two-step conservative level set scheme. The dispersion-relation-preserving schemes are utilized for the advection terms. The pressure Poisson equation solver is applied to GPU computation using the pCDR library developed by National Center for High-Performance Computing, Taiwan. The SMP parallelization is used to accelerate the rest of calculations. Three benchmark problems were done for the performance evaluation. Good agreements with the referenced solutions are demonstrated for all the investigated problems.
Abstract: In this paper we proposed a method for finding video
frames representing one sign in the finger alphabet. The method is
based on determining hands location, segmentation and the use of
standard video quality evaluation metrics. Metric calculation is
performed only in regions of interest. Sliding mechanism for finding
local extrema and adaptive threshold based on local averaging is used
for key frames selection. The success rate is evaluated by recall,
precision and F1 measure. The method effectiveness is compared
with metrics applied to all frames. Proposed method is fast, effective
and relatively easy to realize by simple input video preprocessing
and subsequent use of tools designed for video quality measuring.
Abstract: The major part of light weight timber constructions
consists of insulation. Mineral wool is the most commonly used
insulation due to its cost efficiency and easy handling. The fiber
orientation and porosity of this insulation material enables flowthrough.
The air flow resistance is low. If leakage occurs in the
insulated bay section, the convective flow may cause energy losses
and infiltration of the exterior wall with moisture and particles. In
particular the infiltrated moisture may lead to thermal bridges and
growth of health endangering mould and mildew. In order to prevent
this problem, different numerical calculation models have been
developed. All models developed so far have a potential for
completion. The implementation of the flow-through properties of
mineral wool insulation may help to improve the existing models.
Assuming that the real pressure difference between interior and
exterior surface is larger than the prescribed pressure difference in the
standard test procedure for mineral wool ISO 9053 / EN 29053,
measurements were performed using the measurement setup for
research on convective moisture transfer “MSRCMT".
These measurements show, that structural inhomogeneities of
mineral wool effect the permeability only at higher pressure
differences, as applied in MSRCMT. Additional microscopic
investigations show, that the location of a leak within the
construction has a crucial influence on the air flow-through and the
infiltration rate. The results clearly indicate that the empirical values
for the acoustic resistance of mineral wool should not be used for the
calculation of convective transfer mechanisms.
Abstract: A cancelable palmprint authentication system
proposed in this paper is specifically designed to overcome the
limitations of the contemporary biometric authentication system. In
this proposed system, Geometric and pseudo Zernike moments are
employed as feature extractors to transform palmprint image into a
lower dimensional compact feature representation. Before moment
computation, wavelet transform is adopted to decompose palmprint
image into lower resolution and dimensional frequency subbands.
This reduces the computational load of moment calculation
drastically. The generated wavelet-moment based feature
representation is used to generate cancelable verification key with a
set of random data. This private binary key can be canceled and
replaced. Besides that, this key also possesses high data capture
offset tolerance, with highly correlated bit strings for intra-class
population. This property allows a clear separation of the genuine
and imposter populations, as well as zero Equal Error Rate
achievement, which is hardly gained in the conventional biometric
based authentication system.
Abstract: To learn about China-s future energy demand, this paper first proposed GM(1,1) model group based on recursive solutions of parameters estimation, setting up a general solving-algorithm of the model group. This method avoided the problems occurred on the past researches that remodeling, loss of information and large amount of calculation. This paper established respectively all-data-GM(1,1), metabolic GM(1,1) and new information GM (1,1)model according to the historical data of energy consumption in China in the year 2005-2010 and the added data of 2011, then modeling, simulating and comparison of accuracies we got the optimal models and to predict. Results showed that the total energy demand of China will be 37.2221 billion tons of equivalent coal in 2012 and 39.7973 billion tons of equivalent coal in 2013, which are as the same as the overall planning of energy demand in The 12th Five-Year Plan.
Abstract: Power loss reduction is one of the main targets in power industry and so in this paper, the problem of finding the optimal configuration of a radial distribution system for loss reduction is considered. Optimal reconfiguration involves the selection of the best set of branches to be opened ,one each from each loop, for reducing resistive line losses , and reliving overloads on feeders by shifting the load to adjacent feeders. However ,since there are many candidate switching combinations in the system ,the feeder reconfiguration is a complicated problem. In this paper a new approach is proposed based on a simple optimum loss calculation by determining optimal trees of the given network. From graph theory a distribution network can be represented with a graph that consists a set of nodes and branches. In fact this problem can be viewed as a problem of determining an optimal tree of the graph which simultaneously ensure radial structure of each candidate topology .In this method the refined genetic algorithm is also set up and some improvements of algorithm are made on chromosome coding. In this paper an implementation of the algorithm presented by [7] is applied by modifying in load flow program and a comparison of this method with the proposed method is employed. In [7] an algorithm is proposed that the choice of the switches to be opened is based on simple heuristic rules. This algorithm reduce the number of load flow runs and also reduce the switching combinations to a fewer number and gives the optimum solution. To demonstrate the validity of these methods computer simulations with PSAT and MATLAB programs are carried out on 33-bus test system. The results show that the performance of the proposed method is better than [7] method and also other methods.
Abstract: The paper deals with the estimation of amplitude and phase of an analogue multi-harmonic band-limited signal from irregularly spaced sampling values. To this end, assuming the signal fundamental frequency is known in advance (i.e., estimated at an independent stage), a complexity-reduced algorithm for signal reconstruction in time domain is proposed. The reduction in complexity is achieved owing to completely new analytical and summarized expressions that enable a quick estimation at a low numerical error. The proposed algorithm for the calculation of the unknown parameters requires O((2M+1)2) flops, while the straightforward solution of the obtained equations takes O((2M+1)3) flops (M is the number of the harmonic components). It is applied in signal reconstruction, spectral estimation, system identification, as well as in other important signal processing problems. The proposed method of processing can be used for precise RMS measurements (for power and energy) of a periodic signal based on the presented signal reconstruction. The paper investigates the errors related to the signal parameter estimation, and there is a computer simulation that demonstrates the accuracy of these algorithms.
Abstract: In this study, rotating flexible shaft-disk system
having flexible beams is considered as a dynamic system. After
neglecting nonlinear terms, torsional vibration of the shaft-disk
system and lateral and longitudinal vibration of the flexible beam are
still coupled through the motor speed. The system has three natural
frequencies; the flexible shaft-disk system torsional natural
frequency, the flexible beam lateral and longitudinal natural
frequencies. Eigenvalue calculations show that while the shaft speed
changes, torsional natural frequency of the shaft-disk system and the
beam longitudinal natural frequency are not changing but the beam
lateral natural frequency changes. Beam lateral natural frequency
stays the same as the nonrotating beam lateral natural frequency ωb
until the motor speed ωm is equal to ωb. After then ωb increases and
remains equal to the motor speed ωm until the motor speed is equal to
the shaft-disk system natural frequency ωT. Then the beam lateral
natural frequency ωb becomes equal to the natural frequency ωT and
stays same while the motor speed ωm is increased. Modal amplitudes
and phase angles of the vibrations are also plotted against the motor
speed ωm.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: The purpose of this work is fast design optimization of
the seal chamber. The study includes the mass transfer between lower
and upper chamber on seal chamber for hot water application pumps.
The use of Fluent 12.1 commercial code made it possible to capture
complex flow with heat-mass transfer, radiation, Tailor instability,
and buoyancy effect. Realizable k-epsilon model was used for
turbulence modeling. Radiation heat losses were taken into account.
The temperature distribution at seal region is predicted with respect
to heat addition.
Results show the possibilities of the model simplifications by
excluding the water domain in low chamber from calculations. CFD
simulations permit to improve seal chamber design to meet target
water temperature around the seal. This study can be used for the
analysis of different seal chamber configurations.