Abstract: Crosstalk is the major limiting issue in very high bit-rate digital subscriber line (VDSL) systems in terms of bit-rate or service coverage. At the central office side, joint signal processing accompanied by appropriate power allocation enables complex multiuser processors to provide near capacity rates. Unfortunately complexity grows with the square of the number of lines within a binder, so by taking into account that there are only a few dominant crosstalkers who contribute to main part of crosstalk power, the canceller structure can be simplified which resulted in a much lower run-time complexity. In this paper, a multiuser power control scheme, namely iterative waterfilling, is combined with previously proposed partial crosstalk cancellation approaches to demonstrate the best ever achieved performance which is verified by simulation results.
Abstract: Hot Mix Asphalt (HMA) is one of the most
commonest constructed asphalts in Iran and the quality control of
constructed roads with HMA have been always paid due attention by
researchers. The quality control of constructed roads with this
method is being usually carried out by measuring volumetric
parameters of HMA marshall samples. One of the important
parameters that has a critical role in changing these volumetric
parameters is “compaction temperature"; which as a result of its
changing, volumetric parameters of Marshall Samples and
subsequently constructed asphalt is encountered with variations. In
this study, considering the necessity of preservation of the
compaction temperature, the effect of various temperatures on Hot
Mix Asphalt (HMA) samples properties has been evaluated. As well,
to evaluate the effect of this parameter on different grading, two
different grading (Top coat index grading and binder index grading)
have been used and samples were compacted at 5 various
temperatures.
Abstract: Properties of cement pastes with fine-ground ceramics
used as an alternative binder replacing Portland cement up to 20% of
its mass are investigated. At first, the particle size distribution of
cement and fine-ground ceramics is measured using laser analyser.
Then, the material properties are studied in the early hardening
period up to 28 days. The hydration process of studied materials is
monitored by electrical conductivity measurement using TDR
sensors. The changes of materials- structures within the hardening are
observed using pore size distribution measurement. The compressive
strength measurements are done as well. Experimental results show
that the replacement of Portland cement by fine-ground ceramics in
the amount of up to 20% by mass is acceptable solution from the
mechanical point of view. One can also assume similar physical
properties of designed materials to the reference material with only
Portland cement as binder.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: The paper presents the potential of fuzzy logic (FL-I)
and neural network techniques (ANN-I) for predicting the
compressive strength, for SCC mixtures. Six input parameters that is
contents of cement, sand, coarse aggregate, fly ash, superplasticizer
percentage and water-to-binder ratio and an output parameter i.e. 28-
day compressive strength for ANN-I and FL-I are used for modeling.
The fuzzy logic model showed better performance than neural
network model.
Abstract: Due to growing environmental concerns of the cement
industry, alternative cement technologies have become an area of
increasing interest. It is now believed that new binders are
indispensable for enhanced environmental and durability
performance. Self-compacting Geopolymer concrete is an innovative
method and improved way of concreting operation that does not
require vibration for placing it and is produced by complete
elimination of ordinary Portland cement.
This paper documents the assessment of the compressive strength
and workability characteristics of low-calcium fly ash based selfcompacting
geopolymer concrete. The essential workability
properties of the freshly prepared Self-compacting Geopolymer
concrete such as filling ability, passing ability and segregation
resistance were evaluated by using Slump flow, V-funnel, L-box and
J-ring test methods. The fundamental requirements of high
flowability and segregation resistance as specified by guidelines on
Self Compacting Concrete by EFNARC were satisfied. In addition,
compressive strength was determined and the test results are included
here. This paper also reports the effect of extra water, curing time and
curing temperature on the compressive strength of self-compacting
geopolymer concrete. The test results show that extra water in the
concrete mix plays a significant role. Also, longer curing time and
curing the concrete specimens at higher temperatures will result in
higher compressive strength.
Abstract: The main objective of this paper is to determine the
isolated effect of silica fume on tensile, compressive and flexure strengths on high strength lightweight concrete. Many experiments
were carried out by replacing cement with different percentages of silica fume at different constant water-binder ratio keeping other mix
design variables constant. The silica fume was replaced by 0%, 5%,
10%, 15%, 20% and 25% for a water-binder ratios ranging from 0.26
to 0.42. For all mixes, split tensile, compressive and flexure strengths
were determined at 28 days. The results showed that the tensile, compressive and flexure strengths increased with silica fume incorporation but the optimum replacement percentage is not
constant because it depends on the water–cementitious material (w/cm) ratio of the mix. Based on the results, a relationship between
split tensile, compressive and flexure strengths of silica fume concrete was developed using statistical methods.
Abstract: In this study, an ablation, mechanical and thermal properties of a rocket motor insulation from phenolic/ fiber matrix composites forming a laminate with different fiber between fiberglass and locally available synthetic fibers. The phenolic/ fiber matrix composites was mechanics and thermal properties by means of tensile strength, ablation, TGA and DSC. The design of thermal insulation involves several factors.Determined the mechanical properties according to MIL-I-24768: Density >1.3 g/cm3, Tensile strength >103 MPa and Ablation
Abstract: The present study explains the effect of aggregate
gradation on moisture damage in bituminous mixes. Three types of
aggregate gradation and two types of binder; VG-30 and Polymer
modified bitumen (PMB-40) are used. Moisture susceptibility tests
like retained stability and tensile strength ratio (TSR) and static creep
test are conducted on Marshall specimens. The creep test was also
conducted for conditioned and unconditioned specimens to observe
the effect of moisture on creep behaviour. The results indicate that
Marshall stability value is higher in PMB-40 mix than VG-30 mixes.
Moisture susceptibility of PMB-40 mixes is low when compared with
mix using VG-30. The reduction in retained stability, and indirect
tensile strength and increase in creep are evaluated for finer, coarser
and normal gradation of aggregate to observe the effect of gradation
on moisture susceptibility of mixes. The retained stability is least
affected when compared with other moisture susceptibility
parameters
Abstract: This study has applied the L16 orthogonal array of the
Taguchi method to determine the optimized polymeric
Nanocomposite asphalt binder. Three control factors are defined as
polypropylene plastomer (PP), styrene-butadiene-styrene elastomer
(SBS) and Nanoclay. Four level of concentration contents are
introduced for prepared asphalt binder samples. all samples were
prepared with 4.5% of bitumen 60/70 content. Compressive strength
tests were carried out for defining the optimized sample via
QUALITEK-4 software. SBS with 3%, PP with 5 % and Nanoclay
with 1.5% of concentrations are defined as the optimized
Nanocomposite asphalt binders. The confirmation compressive
strength and also softening point tests showed that modification of
asphalt binders with this method, improved the compressive strength
and softening points of asphalt binders up to 55%.
Abstract: This paper characterizes the effects of artificial short
term aging in the laboratory on the rheological properties of virgin
80/100 penetration grade asphalt binder. After several years in
service, asphalt mixture started to deteriorate due to aging. Aging is a
complex physico-chemical phenomenon that influences asphalt
binder rheological properties causing a deterioration in asphalt
mixture performance. To ascertain asphalt binder aging effects, the
virgin, artificially aged and extracted asphalt binder were tested via
the Rolling Thin film Oven (RTFO), Dynamic Shear Rheometer
(DSR) and Rotational Viscometer (RV). A comparative study
between laboratory and field aging conditions were also carried out.
The results showed that the specimens conditioned for 85 minutes
inside the RTFO was insufficient to simulate the actual short term
aging caused that took place in the field under Malaysian field
conditions
Abstract: One of the important factors of cracks on the asphalt
pavements is bitumen aging that associated with the loss of volatile
components and oxidation of asphalt binder. This paper is about
effect of Styrene-Butadiene-Styrene (SBS) polymer on asphalt aging
In order to decrease asphalt aging effects. For this purpose samples of
base bitumen and SBS modified bitumen aged according to the
rolling thin film oven test (RTFOT) and pressure aging vessel (PAV),
respectively. Properties of each sample were evaluated using Fourier
Transform Infrared (FTIR) spectroscopy, n-heptane precipitation,
viscosity test, softening point test and penetration test. FT-IR
Analysis, showed lower oxidation of SBS modified bitumen than
base bitumen, after aging.