Abstract: Leptospirosis occurs worldwide (except the
poles of the earth), urban and rural areas, developed and
developing countries, especially in Thailand. It can be
transmitted to the human by rats through direct and indirect
ways. Human can be infected by either touching the infected rats
or contacting with water, soil containing urine from the infected
rats through skin, eyes and nose. The data of the people who
are infected with this disease indicates that most of the
patients are adults. The transmission of this disease is studied
through mathematical model. The population is separated into human
and rat. The human is divided into two classes, namely juvenile
and adult. The model equation is constructed for each class. The
standard dynamical modeling method is then used for
analyzing the behaviours of solutions. In addition, the
conditions of the parameters for the disease free and endemic
states are obtained. Numerical solutions are shown to support the
theoretical predictions. The results of this study guide the way to
decrease the disease outbreak.
Abstract: This study is concerned with the investigation of the
suitability of several empirical and semi-empirical drying models
available in the literature to define drying behavior of viscose yarn
bobbins. For this purpose, firstly, experimental drying behaviour of
viscose bobbins was determined on an experimental dryer setup
which was designed and manufactured based on hot-air bobbin
dryers used in textile industry. Afterwards, drying models considered
were fitted to the experimentally obtained moisture ratios. Drying
parameters were drying temperature and bobbin diameter. The fit
was performed by selecting the values for constants in the models in
such a way that these values make the sum of the squared differences
between the experimental and the model results for moisture ratio
minimum. Suitability of fitting was specified as comparing the
correlation coefficient, standard error and mean square deviation.
The results show that the most appropriate model in describing the
drying curves of viscose bobbins is the Page model.
Abstract: Dispersions of casein micelles (CM) were studied at a
constant protein concentration of 5 wt % in high NaCl environment
ranging from 0% to 12% by Dynamic light scattering (DLS) and
Fourier Transform Infrared (FTIR). The rehydration profiles obtained
were interpreted in term of wetting, swelling and dispersion stages by
using a turbidity method. Two behaviours were observed depending
on the salt concentration. The first behaviour (low salt concentration)
presents a typical rehydration profile with a significant change
between 3 and 6% NaCl indicating quick wetting, swelling and long
dispersion stage. On the opposite, the dispersion stage of the second
behaviour (high salt concentration) was significantly shortened
indicating a strong modification of the protein backbone. A salt
increase result to a destabilization of the micelle and the formation of
mini-micelles more or less aggregated indicating an average micelles
size ranging from 100 to 200 nm. For the first time, the estimations
of secondary structural elements (irregular, ß-sheet, α-helix and turn)
by the Amide III assignments were correlated with results from
Amide I.
Abstract: The objective of this research is to examine the shear thinning behaviour of mixing flow of non-Newtonian fluid like toothpaste in the dissolution container with rotating stirrer. The problem under investigation is related to the chemical industry. Mixing of fluid is performed in a cylindrical container with rotating stirrer, where stirrer is eccentrically placed on the lid of the container. For the simulation purpose the associated motion of the fluid is considered as revolving of the container, with stick stirrer. For numerical prediction, a time-stepping finite element algorithm in a cylindrical polar coordinate system is adopted based on semi-implicit Taylor-Galerkin/pressure-correction scheme. Numerical solutions are obtained for non-Newtonian fluids employing power law model. Variations with power law index have been analysed, with respect to the flow structure and pressure drop.
Abstract: In the queueing theory, it is assumed that customer
arrivals correspond to a Poisson process and service time has the
exponential distribution. Using these assumptions, the behaviour of
the queueing system can be described by means of Markov chains
and it is possible to derive the characteristics of the system. In the
paper, these theoretical approaches are presented on several types of
systems and it is also shown how to compute the characteristics in a
situation when these assumptions are not satisfied
Abstract: The objective of this study is to evaluate the threshold
stress of the clay with sand subgrade soil. Threshold stress can be
defined as the stress level above which cyclic loading leads to
excessive deformation and eventual failure. The thickness
determination of highways formations using the threshold stress
approach is a more realistic assessment of the soil behaviour because
it is subjected to repeated loadings from moving vehicles. Threshold
stress can be evaluated by plastic strain criterion, which is based on
the accumulated plastic strain behaviour during cyclic loadings [1].
Several conditions of the all-round pressure the subgrade soil namely,
zero confinement, low all-round pressure and high all-round pressure
are investigated. The threshold stresses of various soil conditions are
determined. Threshold stress of the soil are 60%, 31% and 38.6% for
unconfined partially saturated sample, low effective stress saturated
sample, high effective stress saturated sample respectively.
Abstract: Retinal vascularity assessment plays an important role in diagnosis of ophthalmic pathologies. The employment of digital images for this purpose makes possible a computerized approach and has motivated development of many methods for automated vascular tree segmentation. Metrics based on contingency tables for binary classification have been widely used for evaluating performance of these algorithms and, concretely, the accuracy has been mostly used as measure of global performance in this topic. However, this metric shows very poor matching with human perception as well as other notable deficiencies. Here, a new similarity function for measuring quality of retinal vessel segmentations is proposed. This similarity function is based on characterizing the vascular tree as a connected structure with a measurable area and length. Tests made indicate that this new approach shows better behaviour than the current one does. Generalizing, this concept of measuring descriptive properties may be used for designing functions for measuring more successfully segmentation quality of other complex structures.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: This paper concerns about the experimental and
numerical investigations of energy absorption and axial tearing
behaviour of aluminium 6060 circular thin walled tubes under static
axial compression. The tubes are received in T66 heat treatment
condition with fixed outer diameter of 42mm, thickness of 1.5mm
and length of 120mm. The primary variables are the conical die
angles (15°, 20° and 25°). Numerical simulations are carried on
ANSYS/LS-DYNA software tool, for investigating the effect of
friction between the tube and the die.
Abstract: It is well known that a linear dynamic system including
a delay will exhibit limit cycle oscillations when a bang-bang sensor
is used in the feedback loop of a PID controller. A similar behaviour
occurs when a delayed feedback signal is used to train a neural
network. This paper develops a method of predicting this behaviour
by linearizing the system, which can be shown to behave in a manner
similar to an integral controller. Using this procedure, it is possible
to predict the characteristics of the neural network driven limit cycle
to varying degrees of accuracy, depending on the information known
about the system. An application is also presented: the intelligent
control of a spark ignition engine.
Abstract: In this research, the diffusion of innovation regarding
smartphone usage is analysed through a consumer behaviour theory.
This research aims to determine whether a pattern surrounding the
diffusion of innovation exists. As a methodology, an empirical study
of the switch from a conventional cell phone to a smartphone was
performed. Specifically, a questionnaire survey was completed by
general consumers, and the situational and behavioural characteristics
of switching from a cell phone to a smartphone were analysed. In
conclusion, we found that the speed of the diffusion of innovation, the
consumer behaviour characteristics, and the utilities of the product
vary according to the stage of the product life cycle.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: The dynamic behaviour of a four-bar linkage driven by a velocity controlled DC motor is discussed in the paper. In particular the author presents the results obtained by means of a specifically developed software, which implements the mathematical models of all components of the system (linkage, transmission, electric motor, control devices). The use of this software enables a more efficient design approach, since it allows the designer to check, in a simple and immediate way, the dynamic behaviour of the mechanism, arising from different values of the system parameters.
Abstract: A series of tests on cold-formed steel (CFS) wall plate system subjected to uplift force at the mid span of the wall plate is presented. The aim of the study was to study the behaviour and identify the modes of failure of CFS wall plate system. Two parameters were considered in these studies: 1) different dimension of U-bracket at the supports and 2) different sizes of lipped C-channel. The lipped C-channels used were C07508, C07512 and C10012. The dimensions of the leg of U-bracket were 50x35 mm and 50x60 mm respectively, where 25 mm clearance was provided to the connections for specimens with clearance. Results show that specimens with and without clearance experienced the same mode of failure. Failure began with the yielding of the connectors followed by distortional buckling of the wall plate. However, when C075 sections were used as wall plate, the system behaved differently. There was a large deformation in the wall plate and failure began in the distortional buckling of the wall plate followed by bearing of the connecting plates at the supports (U-bracket). The ultimate strength of the system also decreased dramatically when C075 sections were used.
Abstract: This work considered the thermodynamic feasibility
of scrubbing volatile organic compounds into biodiesel in view of
designing a gas treatment process with this absorbent. A detailed
vapour – liquid equilibrium investigation was performed using the
original UNIFAC group contribution method. The four biodiesels
studied in this work are methyl oleate, methyl palmitate, methyl
linolenate and ethyl stearate. The original UNIFAC procedure was
used to estimate the infinite dilution activity coefficients of 13
selected volatile organic compounds in the biodiesels. The
calculations were done at the VOC mole fraction of 9.213x10-8. Ethyl
stearate gave the most favourable phase equilibrium. A close
agreement was found between the infinite dilution activity coefficient
of toluene found in this work and those reported in literature.
Thermodynamic models can efficiently be used to calculate vast
amount of phase equilibrium behaviour using limited number of
experimental data.
Abstract: In the automotive industry test drives are being conducted
during the development of new vehicle models or as a part of
quality assurance of series-production vehicles. The communication
on the in-vehicle network, data from external sensors, or internal
data from the electronic control units is recorded by automotive
data loggers during the test drives. The recordings are used for fault
analysis. Since the resulting data volume is tremendous, manually
analysing each recording in great detail is not feasible.
This paper proposes to use machine learning to support domainexperts
by preventing them from contemplating irrelevant data and
rather pointing them to the relevant parts in the recordings. The
underlying idea is to learn the normal behaviour from available
recordings, i.e. a training set, and then to autonomously detect
unexpected deviations and report them as anomalies.
The one-class support vector machine “support vector data description”
is utilised to calculate distances of feature vectors. SVDDSUBSEQ
is proposed as a novel approach, allowing to classify subsequences
in multivariate time series data. The approach allows to
detect unexpected faults without modelling effort as is shown with
experimental results on recordings from test drives.
Abstract: One major issue that is regularly cited as a block to
the widespread use of online assessments in eLearning, is that of the
authentication of the student and the level of confidence that an
assessor can have that the assessment was actually completed by that
student. Currently, this issue is either ignored, in which case
confidence in the assessment and any ensuing qualification is
damaged, or else assessments are conducted at central, controlled
locations at specified times, losing the benefits of the distributed
nature of the learning programme. Particularly as we move towards
constructivist models of learning, with intentions towards achieving
heutagogic learning environments, the benefits of a properly
managed online assessment system are clear. Here we discuss some
of the approaches that could be adopted to address these issues,
looking at the use of existing security and biometric techniques,
combined with some novel behavioural elements. These approaches
offer the opportunity to validate the student on accessing an
assessment, on submission, and also during the actual production of
the assessment. These techniques are currently under development in
the DECADE project, and future work will evaluate and report their
use..
Abstract: IVE toolkit has been created for facilitating research,education and development in the field of virtual storytelling and computer games. Primarily, the toolkit is intended for modelling action selection mechanisms of virtual humans, investigating level-of-detail AI techniques for large virtual environments, and for exploring joint behaviour and role-passing technique (Sec. V). Additionally, the toolkit can be used as an AI middleware without any changes. The main facility of IVE is that it serves for prototyping both the AI and virtual worlds themselves. The purpose of this paper is to describe IVE's features in general and to present our current work - including an educational game - on this platform.
Abstract: Existing literature ondesign reasoning seems to give
either one sided accounts on expert design behaviour based on
internal processing. In the same way ecological theoriesseem to
focus one sidedly on external elementsthat result in a lack of unifying
design cognition theory. Although current extended design cognition
studies acknowledge the intellectual interaction between internal and
external resources, there still seems to be insufficient understanding
of the complexities involved in such interactive processes. As
such,this paper proposes a novelmulti-directional model for design
researchers tomap the complex and dynamic conduct controlling
behaviour in which both the computational and ecological
perspectives are integrated in a vertical manner. A clear distinction
between identified intentional and emerging physical drivers, and
relationships between them during the early phases of experts- design
process, is demonstrated by presenting a case study in which the
model was employed.
Abstract: Intelligent technologies are increasingly facilitating
sustainable water management strategies in Australia. While this
innovation can present clear cost benefits to utilities through
immediate leak detection and deference of capital costs, the impact of
this technology on households is less distinct. By offering real-time
engagement and detailed end-use consumption breakdowns, there is
significant potential for demand reduction as a behavioural response
to increased information. Despite this potential, passive
implementation without well-planned residential engagement
strategies is likely to result in a lost opportunity. This paper begins
this research process by exploring the effect of smart water meters
through the lens of three behaviour change theories. The Theory of
Planned Behaviour (TPB), Belief Revision theory (BR) and Practice
Theory emphasise different variables that can potentially influence
and predict household water engagements. In acknowledging the
strengths of each theory, the nuances and complexity of household
water engagement can be recognised which can contribute to
effective planning for residential smart meter engagement strategies.