Abstract: The concentrations of cadmium and lead in sewage
sludge samples were determined by Atomic Absorption
Spectrometric Method. Samples of sewage sludge were obtained
from three sewage treatment plants localised in Middle Region of
Libya (Misrata, Msallata and Tarhünah cities).
The results shows that, the mean levels of Cadmium for all regions
are ranges from 81 to 123.4 ppm and these values are higher than the
limitations for the international standard which are not registered
more than 50 ppm (dry weight) in USA, Egypt and the EU countries.
While, the lead concentrations are ranged from 8.0 to 189.2 ppm and
all values are within the standard limits which graduated between
(275–613) ppm.
Abstract: The concentration levels of six heavy metals (Cd, Cr,
Fe, Ni, Pb and Zn) and two mineral elements (Ca and Mg) were
determined in soil samples collected from the vicinity of two auto
mechanic workshops in Sabon-Gari, Kaduna state, Nigeria, using
Atomic Absorption Spectrometry (AAS), in order to compare the
gradation of their concentrations with distance and depth of soil from
the workshop sites. At site 1, concentrations of Lead, Chromium, Iron
and Zinc were generally found to be above the World Health
Organization limits, while those of Nickel and Cadmium fell within
the limits. Iron had the highest concentration with a range of 176.274
ppm to 489.127 ppm at depths of 5 cm to 15 cm and a distance range
of 5 m to 15 m, while the concentration of cadmium was least with a
range of 0.001 ppm to 0.008 ppm at similar depth and distance
ranges. In addition, there was more of calcium (11.521 ppm to
121.709 ppm), in all the samples, than magnesium (11.293 ppm to
21.635 ppm). Similar results were obtained for site II. The
concentrations of all the metals analyzed showed a downward
gradient with increase in depth and distance from both workshop sites
except for iron and zinc at site 2. The immediate and remote
implications of these findings on the biota are discussed.
Abstract: Due to the determination of the pollution status of
fresh resources in the Egyptian territorial waters is very important for
public health; this study was carried out to reveal the levels of heavy
metals in the shellfish and their environment and its relation to the
highly developed industrial activities in those areas. A total of 100
shellfish samples from the Rosetta, Edku, El-Maadiya, Abo-Kir and
El-Max coasts [10 crustaceans (shrimp) and 10 mollusks (oysters)]
were randomly collected from each coast. Additionally, 10 samples
from both the water and the sediment were collected from each coast.
Each collected sample was analyzed for cadmium, chromium,
copper, lead and zinc residues using a Perkin Elmer atomic
absorption spectrophotometer (AAS). The results showed that the
levels of heavy metals were higher in the water and sediment from
Abo-Kir. The heavy metal levels decreased successively for the
Rosetta, Edku, El-Maadiya, and El-Max coasts, and the
concentrations of heavy metals, except copper and zinc, in shellfish
exhibited the same pattern. For the concentration of heavy metals in
shellfish tissue, the highest was zinc and the concentrations decreased
successively for copper, lead, chromium and cadmium for all coasts,
except the Abo-Kir coast, where the chromium level was highest and
the other metals decreased successively for zinc, copper, lead and
cadmium. In Rosetta, chromium was higher only in the mollusks,
while the level of this metal was lower in the crustaceans; this trend
was observed at the Edku, El-Maadiya and El-Max coasts as well.
Herein, we discuss the importance of such contamination for public
health and the sources of shellfish contamination with heavy metals.
We suggest measures to minimize and prevent these pollutants in the
aquatic environment and, furthermore, how to protect humans from
excessive intake.
Abstract: Multiwall carbon nanotubes, prepared by chemical
vapor deposition, have an average diameter of 60-100 nm as shown
by High Resolution Transmittance Electron Microscope, HR-TEM.
The Multiwall carbon nanotubes (MWCNTs) were further
characterized using X-ray Diffraction and Raman Spectroscopy.
Mercury uptake capacity of MWCNTs was studied using batch
adsorption method at different concentration ranges up to 150 ppm.
Mercury concentration (before and after the treatment) was measured
using cold vapor atomic absorption spectroscopy. The effect of time,
concentration, pH and adsorbent dose were studied. MWCNT were
found to perform complete absorption in the sub-ppm concentrations
(parts per billion levels) while for high concentrations, the adsorption
efficiency was 92% at the optimum conditions; 0.1 g of the adsorbent
at 150 ppm mercury (II) solution. The adsorption of mercury on
MWCNTs was found to follow the Freundlich adsorption isotherm
and the pseudo-second order kinetic model.
Abstract: Pollution of the Klip River has caused
microorganisms inhabiting it to develop protective survival
mechanisms. This study isolated and characterized the heavy metal
resistant bacteria in the Klip River. Water and sediment samples were
collected from six sites along the course of the river. The pH,
turbidity, salinity, temperature and dissolved oxygen were measured
in-situ. The concentrations of six heavy metals (Cd, Cu, Fe, Ni, Pb
and Zn) of the water samples were determined by atomic absorption
spectroscopy. Biochemical and antibiotic profiles of the isolates were
assessed using the API 20E® and Kirby Bauer Method. Growth
studies were carried out using spectrophotometric methods. The
isolates were identified using 16SrDNA sequencing. The uppermost
part of the Klip River with the lowest pH had the highest levels of
heavy metals. Turbidity, salinity and specific conductivity increased
measurably at Site 4 (Henley on Klip Weir). MIC tests showed that
16 isolates exhibited high iron and lead resistance. Antibiotic
susceptibility tests revealed that the isolates exhibited multitolerances
to drugs such as Tetracycline, Ampicillin, and
Amoxicillin.
Abstract: Various biomass based resources, which can be used
as an extender, or a complete substitute of diesel fuel may have very
significant role in the development of agriculture, industrial and
transport sectors in the energy crisis. Use of Karanja oil methyl ester
biodiesel in a CI DI engine was found highly compatible with engine
performance along with lower exhaust emission as compared to
diesel fuel but with slightly higher NOx emission and low wear
characteristics. The combustion related properties of vegetable oils
are somewhat similar to diesel oil. Neat vegetable oils or their blends
with diesel, however, pose various long-term problems in
compression ignition engines. These undesirable features of
vegetable oils are because of their inherent properties like high
viscosity, low volatility, and polyunsaturated character. Pongamia
methyl ester (PME) was prepared by transesterification process using
methanol for long term engine operations. The physical and
combustion-related properties of the fuels thus developed were found
to be closer to that of the diesel. A neat biodiesel (PME) was selected
as a fuel for the tribological study of biofuels.
Two similar new engines were completely disassembled and
subjected to dimensioning of various vital moving parts and then
subjected to long-term endurance tests on neat biodiesel and diesel
respectively. After completion of the test, both the engines were
again disassembled for physical inspection and wear measurement of
various vital parts. The lubricating oil samples drawn from both
engines were subjected to atomic absorption spectroscopy (AAS) for
measurement of various wear metal traces present. The additional
lubricating property of biodiesel fuel due to higher viscosity as
compared to diesel fuel resulted in lower wear of moving parts and
thus improved the engine durability with a bio-diesel fuel. Results
reported from AAS tests confirmed substantially lower wear and thus
improved life for biodiesel operated engines.
Abstract: A study was conducted in May to July 2013 with the aim of determination of heavy metal concentration in orchard area. 60 samples were collected and analyzed for Cadmium (Cd), Copper (Cu), Lead (Pb), and Zinc (Zn) by Atomic Absorption Spectrophotometer (AAS).
The heavy metal concentrations in sediment of orchards, that use chemical for Cd (1.13 ± 0.26 mg/l), Cu (8.00 ± 1.05 mg/l), Pb (13.16 ± 2.01) and Zn (37.41 ± 3.20 mg/l). The heavy metal concentrations in sediment of the orchards, that do not use chemical for Cd (1.28 ± 0.50 mg/l), Cu (7.60 ± 1.20 mg/l), Pb (29.87 ± 4.88) and Zn (21.79 ± 2.98 mg/l). Statistical analysis between heavy metal in sediment from the orchard, that use chemical and the orchard, that not use chemical were difference statistic significant of 0.5 level of significant for Cd and Pb while no statistically difference for Cu and Zn.
Abstract: This research aims to study the Zinc (Zn) concentration in fine particulate matter on Rajchawithee roadside in rush hour. 30 Samples were collected in Jun to August 2013 by 8 stage non-avaible cascade impactor. Each samples (filter paper) were digest with nitric acid and analyed by atomic absorption spectrophotometer for Zinc determination. The highest value for the mean fraction (18.00 ± 9.28%) is the size 9.0 – 110.0 micron follow by the range 3.3 – 4.7 micron (14.77 ± 14.66 %) and 1.1 – 2.1 micron (14.01 ± 11.77 %). The concentration of Zn in the particulate matter of range 0.43 – 0.7mm, 0.7 – 1.1 mm, 1.1 – 2.1 mm, 2.1 – 3.3 mm, 3.3 – 4.7 mm, 4.7 – 5.8 mm, 5.8 – 9.0 mm, 9.0 – 10.0 mm, were 41.56 – 217.62 mg/m3 (175.86 ±32.25 mg/m3), 152.60 – 217.24 mg/m3 (187.71 ± 17.42 mg/m3), 142.90 – 214.67 mg/m3(180.95 ± 18.71 mg/m3), 155.48 – 218.19 mg/m3(183.22 ± 19.94 mg/m3), 151.72 – 217.39 mg/m3(181.85 ± 17.57 mg/m3), 133.86 – 220.17 mg/m3 (178.78 ± 23.45 mg/m3), 160.00 – 220.35 mg/m3 (182.58 ± 18.08 mg/m3), 153.30 – 226.70 mg/m3 (181.52 ± 20.05 mg/m3), respectively. The Zn concentration in each size of particulate matter was not statistically significant different (p > .005)
Abstract: Diverse contaminants released into the environment through progress of urbanization and industrialization adversely affect human health. Among various sources of contaminants, especially, in big cities, automobiles play a significant role in aggravating the pollution. Various pollutants viz., heavy metals (Pb, Mn, Ni, Zn, As, Hg, Cd) and Polyaromatic hydrocarbons (Benzo-a-pyrene, fluoranthene, pyrene, benzo-b-anthracene, benzo-b-fluoranthene, acenaphthylene, fluorine, phenantherene, anthracene, chrysene, benzo-k-fluoranthene, benzo-e-pyrene, indenol-1,2,3-cd-pyrene, dibenzo-a,h-anthracene, benzo-ghi-perylene) are released by vehicles. Further, these pollutants are expected to cause severe mutagenic, genotoxic and carcinogenic effects. Considering this, many authors monitored the levels of pollution in roadside soil, water and plants. The present review focuses upon the analysis and effects of heavy metals and polycyclic aromatic hydrocarbons from the roadside samples.
Abstract: The study realized on alive lambs in two different areas mountain and plain in Batna region, aims to demonstrate the possible effect of field type on cupric status of lambs, through evaluation of copper contents in the chain: soil – plant – animal by atomic absorption spectrophotometry. This comparative study also allowed the investigation of the influence of the age and the season. The results obtained show that contents of copper in the soil, forage in the same way as in the plasma of lambs are higher in the plain than in the mountainous area; however, the difference is significant only between the values of feed.
Abstract: Polystyrene (PS) was extracted from Styrofoam (expanded polystyrene foam) waste, so called white pollutant. The PS was functionalized with N,N- Bis(2-aminobenzylidene)benzene-1,2-diamine (ABA) ligand through an azo spacer. The resin was characterized by FT-IR spectroscopy and elemental analysis. The PS-N=N-ABA resin was used for the enrichment and speciation of Cr(III)/Cr(VI) ions and total Cr determination in aqueous samples by flame atomic absorption spectrometry (FAAS). The separation of Cr(III)/Cr(VI) ions was achieved at pH 2. The recovery of Cr(VI) ions was achieved ≥ 95.0% at optimum parameters: pH 2; resin amount 300mg; flow rates 2.0mL min-1 of solution and 2.0mL min-1 of eluent (2.0mol L-1 HNO3). Total Cr was determined by oxidation of Cr(III) to Cr(VI) ions using H2O2. The limit of detection (LOD) and quantification (LOQ) of Cr(VI) were found to be 0.40 and 1.20μg L-1, respectively with preconcentration factor of 250. Total saturation and breakthrough capacitates of the resin for Cr(IV) ions were found to be 0.181 and 0.531mmol g-1, respectively. The proposed method was successfully applied for the preconcentration/speciation of Cr(III)/Cr(VI) ions and determination of total Cr in industrial effluents.
Abstract: The health and environmental risk of eating mushrooms grown in Abakaliki were evaluated in terms of heavy metals accumulation. Mushroom samples were collected from four different farms located at Izzi, Amajim, Amana and Amudo and analyzed for (iron, lead, manganese and cadmium) using Bulk Scientific Atomic Absorption Spectrophotometer 205. Results indicates mean range of concentrations of the trace metals in the mushrooms were Fe (0.22-152. 03), Mn (0.74-9.76), Pb (0.01.0.80), Cd (0.61-0.82) mg/L respectively. Accumulation of Cd on the four locations under investigation was higher than the UK Government Food Science Surveillance and World Health Organization maximum recommended levels in mushroom for human consumption. The Fe and Mn contaminants of Amudo were significant and show the impact of anthropogenic/atmospheric pollution. The potential sources of the heavy metals in the mushrooms were from urban waste, dust from mining and quarrying activities, natural geochemistry of the area, and use of inorganic fertilizers
Abstract: Since nickel is a known toxic and carcinogenic metal, the present study was designed to evaluate the level of nickel released into the saliva of orthodontic patients. Non-stimulated saliva was collected from 18 patients attending The Orthodontic Clinic of Dental Faculty of Benghazi University. Patients were divided into two groups and level of nickel was determined by atomic absorption spectrophotometry. Nickel concentration value (mg/L) in first group prior to starting treatment was 0.097± 0.071. An increase in level of nickel was followed by decrease 4 and 8 weeks after applying the arch wire (0.208± 0.112) and (0.077±0.056 mg/L) respectively. Nickel levels in saliva of the second group were showed minimal variation and ranged from 0.061± 0.044mg/L to 0.083±0.054 throughout period of study. It may be concluded that there could be a release of nickel from the appliances used in first group but it doesn't reach toxic level in saliva.
Abstract: The aim of this research paper was based on an examination of sources of water supply and water quality for local consumption, conducted at eco- tourism villages of Suan Luang Sub- District Municipality of Amphawa District, Samut Songkram Province. The study incorporated both questionnaire and field work of water testing as the research tool and method. The sample size of 288 households was based on the population of the district, whereas the selected sample water sources were from 60 households: 30 samples were ground water and another 30 were surface water. Degree of heavy metal contamination in the water including copper, iron, manganese, zinc, cadmium and lead was investigated utilizing the Atomic Absorption- Direct Aspiration method. The findings unveiled that 96.0 percent of household water consumption was based on water supply, while the rest on canal, river and rain water. The household behavior of consumption revealed that 47.2 percent of people routinely consumed water without boiling or filtering prior to consumption. The investigation of water supply quality found that the degree of heavy metal contamination including metal, lead, iron, copper, manganese and cadmium met the standards of the Department of Health.
Abstract: The environmental pollution by heavy metals became
more problematic nowadays. To solve the problem of Cadmium
accumulation in human organs which lead to dangerous effects on
human health, and to determine its concentration, the organic legand
1-phenyl-3-benzoyl-2-thiourea was used to extract the cadmium ions
from its solution. This legand as one of thiourea derivatives was
successfully synthesized. The legand was characterized by NMR and
CHN elemental analysis, and used to extract the cadmium from its
solutions by formation of a stable complex at neutral pH. The
complex was characterized by elemental analysis and melting point.
The concentrations of cadmium ions before and after the extraction
were determined by Atomic Absorption Spectrophotometer (AAS).
The data show the percentage of the extract was more than 98.7% of
the concentration of cadmium used in the study
Abstract: The textile industry produces highly coloured
effluents containing polar and non-polar compounds. The textile mill
run by the Assam Polyester Co-operative Society Limited (APOL) is
situated at Rangia, about 55 km from Guwahati (26011' N, 91047' E)
in the northern bank of the river Brahmaputra, Assam (India). This
unit was commissioned in June 1988 and started commercial
production in November 1988. The installed capacity of the weaving
unit was 8000 m/day and that of the processing unit was 20,000
m/day. The mill has its own dyeing unit with a capacity of 1500-2000
kg/day. The western side of the mill consists of vast agricultural land
and the far northern and southern side of the mill has scattered human
population. The eastern side of the mill has a major road for
thoroughfare. The mill releases its effluents into the agricultural land
in the western side of the mill. The present study was undertaken to
assess the impact of the textile mill on surface soil quality in and
around the mill with particular reference to Cr, Mn, Ni and Zn.
Surface soil samples, collected along different directions at 200, 500
and 1000 m were digested and the metals were estimated with
Atomic Absorption Spectrophotometer. The metals were found in the
range of: Cr 50.9 – 105.0 mg kg-1, Mn 19.2- 78.6 mg kg-1, Ni 41.9 –
50.6 mg kg-1 and Zn 187.8 – 1095.8 mg kg-1. The study reveals
enrichment of Cr, Mn, Ni and Zn in the soil near the textile mill.
Abstract: There are many sources trough which the soil get
enriched and contaminated with REEs. The determination of REEs in
environmental samples has been limited because of the lack of
sensitive analytical techniques. Soil samples were collected from
four sites including open cast coal mine, natural coal burning, coal
washery and control in the coal field located in Dhanbad, India.
Total concentrations of rare earth elements (REEs) were determined
using the inductively coupled plasma atomic absorption spectrometry
in order to assess enrichment status in the coal field. Results showed
that the mean concentrations of La, Pr, Eu, Tb, Ho, and Tm in open
cast mine and natural coal burning sites were elevated compared to
the reference concentrations, while Ce, Nd, Sm, and Gd were
elevated in coal washery site. When compared to reference soil,
heavy REEs (HREEs) were enriched in open cast mines and natural
coal burning affected soils, however, the HREEs were depleted in the
coal washery sites. But, the Chondrite-normalization diagram showed
significant enrichment for light REEs (LREEs) in all the soils. High
concentration of Pr, Eu, Tb, Ho, Tm, and Lu in coal mining and coal
burning sites may pose human health risks. Factor analysis showed
that distribution and relative abundance of REEs of the coal washery
site is comparable with the control. Eventually washing or cleaning
of coal could significantly decrease the emission of REEs from coal
into the environment.
Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: In this research the level of mercury is analyzed in
muscle tissue of Otolithes ruber retailed in Hamedan, Iran were
determined by flame atomic absorption spectrometry after wet
digestion. Analysis of mercury was carried out by
spectrophotometrically. The average concentration of Hg in muscle
tissue of Otolithes ruber was 0.030±0.026 -g/g so lower than to
compare with the Maximum Allowable Concentration determined by
FAO/WHO Codex Alimentarius Commission.
Abstract: A new chelating resin is prepared by coupling
Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer.
The resulting sorbent has been characterized by FT-IR, elemental
analysis and thermogravimetric analysis (TGA) and studied for
preconcentrating of Cu (II) using flame atomic absorption
spectrometry (FAAS) for metal monitoring. The optimum pH value
for sorption of the copper ions was 6.5. The resin was subjected to
evaluation through batch binding of mentioned metal ion.
Quantitative desorption occurs instantaneously with 0.5 M HNO3.
The sorption capacity was found 4.8 mmol.g-1 of resin for Cu (II) in
the aqueous solution. The chelating resin can be reused for 10 cycles
of sorption-desorption without any significant change in sorption
capacity. A recovery of 99% was obtained the metal ions with 0.5 M
HNO3 as eluting agent. The method was applied for metal ions
determination from industrial waste water sample.