Abstract: Thermal behavior of fuel channel under loss of coolant accident (LOCA) is a major concern for nuclear reactor safety. LOCA along with failure of emergency cooling water system (ECC) may leads to mechanical deformations like sagging and ballooning. In order to understand the phenomenon an experiment has been carried out using 19 pin fuel element simulator. Main purpose of the experiment was to trace temperature profiles over the pressure tube, calandria tube and clad tubes of Indian Pressurized Heavy Water Reactor (IPHWR) under symmetrical and asymmetrical heat-up conditions. For simulating the fully voided scenario, symmetrical heating of pressure was carried out by injecting 13.2 KW (2 % of nominal power) to all the 19 pins and the temperatures of pressure tube, calandria tube and clad tubes were measured. During symmetrical heating the sagging of fuel channel was initiated at 460 °C and the highest temperature attained by PT was 650 °C . The decay heat from clad tubes was dissipated to moderator mainly by radiation and natural convection. The highest temperature of 680 °C was observed over the outer ring of clad tubes of fuel simulator. Again, to simulate partially voided condition, asymmetrical heating of pressure was carried out by supplying 8.0 kW power to upper 8 pins of fuel simulator and temperature profiles were measured. Along the circumference of pressure tube (PT) the highest temperature difference of 320 °C was observed, which highlights the magnitude of thermal stresses under partially voided conditions.
Abstract: This paper presents a new ultra-wideband (UWB) bandpass filter (BPF) with sharp roll-off and dual-notched bands. The filter consists of a triangle ring multi-mode resonator (MMR) with the stub-loaded resonator (SLR) for controlling the two transmission zeros at 2.8 / 11 GHz, the embedded open-circuited stub and the asymmetric tight coupled input/output (I/O) lines for introducing the dual notched bands at 5.2 / 6.8 GHz. The attenuation slope in the lower and higher passband edges of the proposed filter show 160- and 153-dB/GHz, respectively. This study mainly provides a simple method to design a UWB bandpass filter with high passband selectivity and dual-notched bands for satisfying the Federal Communications Commission (FCC-defined) indoor UWB specification
Abstract: A device analysis of the photoconductive
semiconductor switch is carried out to investigate distribution of
electric field and carrier concentrations as well as the current density
distribution. The operation of this device was then investigated as a
switch operating in X band. It is shown that despite the presence of
symmetry geometry, switch current density of the on-state steady
state mode is distributed asymmetrically throughout the device.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: Noise contamination in a magnetic resonance (MR)
image could occur during acquisition, storage, and transmission in
which effective filtering is required to avoid repeating the MR
procedure. In this paper, an iterative asymmetrical triangle fuzzy
filter with moving average center (ATMAVi filter) is used to reduce
different levels of salt and pepper noise in a brain MR image. Besides
visual inspection on filtered images, the mean squared error (MSE) is
used as an objective measurement. When compared with the median
filter, simulation results indicate that the ATMAVi filter is effective
especially for filtering a higher level noise (such as noise density =
0.45) using a smaller window size (such as 3x3) when operated
iteratively or using a larger window size (such as 5x5) when operated
non-iteratively.
Abstract: The article deals with dividends and their distribution from investors from a theoretical point of view. Some studies try to analyzed the reaction of the market on the dividend announcement and found out the change of dividend policy is associated with abnormal returns around the dividend announcement date. Another researches directly questioned the investors about their dividend preference and beliefs. Investors want the dividend from many reasons (e.g. some of them explain the dividend preference by the existence of transaction cost; investors prefer the dividend today, because there is less risky; the managers have private information about the firm). The most controversial theory of dividend policy was developed by Modigliani and Miller (1961) who demonstrated that in the perfect and complete capital markets the dividend policy is irrelevant and the value of the company is independent of its payout policy. Nevertheless, in the real world the capital markets are imperfect, because of asymmetric information, transaction costs, incomplete contracting possibilities and taxes.
Abstract: In this work, we used the single Langmuir probe to
measure the plasma density distribution in an geometrically
asymmetric capacitive coupled plasma discharge system. Because of
the frame structure of powered electrode, the plasma density was not
homogeneous in the discharge volume. It was higher under the frame,
but lower in the centre. Finite element simulation results showed a
good agreement with the experiment results. To increase the electron
density in the central volume and improve the homogeneity of the
plasma, we added an auxiliary electrode, powered by DC voltage, in
the simulation geometry. The simulation results showed that the
auxiliary electrode could alter the potential distribution and improve
the density homogeneity effectively.
Abstract: MinC plays an important role in bacterial cell division
system by inhibiting FtsZ assembly. However, the molecular
mechanism of the action is poorly understood. E. coli MinC Nterminus
domain was purified and crystallized using 1.4 M sodium
citrate pH 6.5 as a precipitant. X-ray diffraction data was collected
and processed to 2.3 Å from a native crystal. The crystal belonged to
space group P212121, with the unit cell parameters a = 52.7, b = 54.0,
c = 64.7 Å. Assuming the presence of two molecules in the
asymmetric unit, the Matthews coefficient value is 1.94 Å3 Da-1,
which corresponds to a solvent content of 36.5%. The overall
structure of MinCN is observed as a dimer form through anti-parallel
ß-strand interaction.
Abstract: In this work, an organic compound 5,10,15,20-
Tetrakis(3,5-di-tertbutylphenyl)porphyrinatocopper(II) (TDTBPPCu)
is studied as an active material for thin film electronic devices. To
investigate the electrical properties of TDTBPPCu, junction of
TDTBPPCu with heavily doped n-Si and Al is fabricated.
TDTBPPCu film was sandwiched between Al and n-Si electrodes.
Various electrical parameters of TDTBPPCu are determined. The
current-voltage characteristics of the junction are nonlinear,
asymmetric and show rectification behavior, which gives the clue of
formation of depletion region. This behavior indicates the potential
of TDTBPPCu for electronics applications. The current-voltage and
capacitance-voltage techniques are used to find the different
electronic parameters.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: With the drastically growth in optical communication
technology, a lossless, low-crosstalk and multifunction optical switch
is most desirable for large-scale photonic network. To realize such a
switch, we have introduced the new architecture of optical switch
that embedded many functions on single device. The asymmetrical
architecture of OXADM consists of 3 parts; selective port, add/drop
operation, and path routing. Selective port permits only the interest
wavelength pass through and acts as a filter. While add and drop
function can be implemented in second part of OXADM architecture.
The signals can then be re-routed to any output port or/and perform
an accumulation function which multiplex all signals onto single path
and then exit to any interest output port. This will be done by path
routing operation. The unique features offered by OXADM has
extended its application to Fiber to-the Home Technology (FTTH),
here the OXADM is used as a wavelength management element in
Optical Line Terminal (OLT). Each port is assigned specifically with
the operating wavelengths and with the dynamic routing management
to ensure no traffic combustion occurs in OLT.
Abstract: By introducing the concept of Oracle we propose an approach for improving the performance of genetic algorithms for large-scale asymmetric Traveling Salesman Problems. The results have shown that the proposed approach allows overcoming some traditional problems for creating efficient genetic algorithms.
Abstract: When the profile information of an existing road is
missing or not up-to-date and the parameters of the vertical
alignment are needed for engineering analysis, the engineer has to recreate
the geometric design features of the road alignment using
collected profile data. The profile data may be collected using
traditional surveying methods, global positioning systems, or digital
imagery. This paper develops a method that estimates the parameters
of the geometric features that best characterize the existing vertical
alignments in terms of tangents and the expressions of the curve, that
may be symmetrical, asymmetrical, reverse, and complex vertical
curves. The method is implemented using an Excel-based
optimization method that minimizes the differences between the
observed profile and the profiles estimated from the equations of the
vertical curve. The method uses a 'wireframe' representation of the
profile that makes the proposed method applicable to all types of
vertical curves. A secondary contribution of this paper is to introduce
the properties of the equal-arc asymmetrical curve that has been
recently developed in the highway geometric design field.
Abstract: In this work, we examine fluid mixing in a full three-stream mixing channel with longitudinal vortex generators (LVGs) built on the channel bottom by numerical simulation and experiment. The effects of the asymmetrical arrangement and the attack angle of the LVGs on fluid mixing are investigated. The results show that the micromixer with LVGs at a small asymmetry index (defined by the ratio of the distance from the center plane of the gap between the winglets to the center plane of the main channel to the width of the main channel) is superior to the micromixer with symmetric LVGs and that with LVGs at a large asymmetry index. The micromixer using five mixing modules of the LVGs with an attack angle between 16.5 degrees and 22.5 degrees can achieve excellent mixing over a wide range of Reynolds numbers. Here, we call a section of channel with two pairs of staggered asymmetrical LVGs a mixing module. Besides, the micromixer with LVGs at a small attack angle is more efficient than that with a larger attack angle when pressure losses are taken into account.
Abstract: A numerical study is presented on buckling and post
buckling behaviour of laminated carbon fiber reinforced plastic
(CFRP) thin-walled cylindrical shells under axial compression using
asymmetric meshing technique (AMT). Asymmetric meshing
technique is a perturbation technique to introduce disturbance without
changing geometry, boundary conditions or loading conditions.
Asymmetric meshing affects predicted buckling load, buckling mode
shape and post-buckling behaviour. Linear (eigenvalue) and nonlinear
(Riks) analyses have been performed to study the effect of
asymmetric meshing in the form of a patch on buckling behaviour.
The reduction in the buckling load using Asymmetric meshing
technique was observed to be about 15%. An isolated dimple formed
near the bifurcation point and the size of which increased to reach a
stable state in the post-buckling region. The load-displacement curve
behaviour applying asymmetric meshing is quite similar to the curve
obtained using initial geometric imperfection in the shell model.
Abstract: The third generation (3G) of cellular system adopted
the spread spectrum as solution for the transmission of the data in the
physical layer. Contrary to systems IS-95 or CDMAOne (systems
with spread spectrum of the preceding generation), the new standard,
called Universal Mobil Telecommunications System (UMTS), uses
long codes in the down link. The system is conceived for the vocal
communication and the transmission of the data. In particular, the
down link is very important, because of the asymmetrical request of
the data, i.e., more remote loading towards the mobiles than towards
the basic station. Moreover, the UMTS uses for the down link an
orthogonal spreading out with a variable factor of spreading out
(OVSF for Orthogonal Variable Spreading Factor). This
characteristic makes it possible to increase the flow of data of one or
more users by reducing their factor of spreading out without
changing the factor of spreading out of other users. In the current
standard of the UMTS, two techniques to increase the performances
of the down link were proposed, the diversity of sending antenna and
the codes space-time. These two techniques fight only fainding. The
receiver proposed for the mobil station is the RAKE, but one can
imagine a receiver more sophisticated, able to reduce the interference
between users and the impact of the coloured noise and interferences
to narrow band. In this context, where the users have long codes
synchronized with variable factor of spreading out and ignorance by
the mobile of the other active codes/users, the use of the sequences of
code pseudo-noises different lengths is presented in the form of one
of the most appropriate solutions.
Abstract: In this paper we study a system composed by carbon
nanotube (CNT) and bundle of carbon nanotube (BuCNT) interacting
with a specific fatty acid as molecular probe. Full system is
represented by open nanotube (or nanotubes) and the linoleic acid
(LA) relaxing due the interaction with CNT and BuCNT. The LA has
in his form an asymmetric shape with COOH termination provoking
a close BuCNT interaction mainly by van der Waals force field. The
simulations were performed by classical molecular dynamics with
standard parameterizations.
Our results show that these BuCNT and CNT are dynamically
stable and it shows a preferential interaction position with LA
resulting in three features: (i) when the LA is interacting with CNT
and BuCNT (including both termination, CH2 or COOH), the LA is
repelled; (ii) when the LA terminated with CH2 is closer to open
extremity of BuCNT, the LA is also repelled by the interaction
between them; and (iii) when the LA terminated with COOH is
closer to open extremity of BuCNT, the LA is encapsulated by the
BuCNT. These simulations are part of a more extensive work on
searching efficient selective molecular devices and could be useful to
reach this goal.
Abstract: This research is aimed to compare the percentages of correct classification of Empirical Bayes method (EB) to Classical method when data are constructed as near normal, short-tailed and long-tailed symmetric, short-tailed and long-tailed asymmetric. The study is performed using conjugate prior, normal distribution with known mean and unknown variance. The estimated hyper-parameters obtained from EB method are replaced in the posterior predictive probability and used to predict new observations. Data are generated, consisting of training set and test set with the sample sizes 100, 200 and 500 for the binary classification. The results showed that EB method exhibited an improved performance over Classical method in all situations under study.
Abstract: It is known that an analog Hopfield neural network
with time delay can generate the outputs which are similar to the
human electroencephalogram. To gain deeper insights into the
mechanisms of rhythm generation by the Hopfield neural networks
and to study the effects of noise on their activities, we investigated
the behaviors of the networks with symmetric and asymmetric
interneuron connections. The neural network under the study consists
of 10 identical neurons. For symmetric (fully connected) networks all
interneuron connections aij = +1; the interneuron connections for
asymmetric networks form an upper triangular matrix with non-zero
entries aij = +1. The behavior of the network is described by 10
differential equations, which are solved numerically. The results of
simulations demonstrate some remarkable properties of a Hopfield
neural network, such as linear growth of outputs, dependence of
synchronization properties on the connection type, huge
amplification of oscillation by the external uniform noise, and the
capability of the neural network to transform one type of noise to
another.
Abstract: We theoretically demonstrate modulation of light
polarization by a crossed rectangular hole array with asymmetric arm
lengths. There are two waveguide modes that can modulate the x- and
y- polarized incident waves independently. A specific structure is
proposed to convert a left-hand incident wave to a right-hand outgoing
wave by transmission.