Abstract: Rotating disk is one of the most indispensable parts of a rotating machine. Rotating disk has found many applications in the diverging field of science and technology. In this paper, we have taken into consideration the problem of a heavy spinning disk mounted on a rotor system acted upon by boundary traction. Finite element modelling is used at various loading condition to determine the mixed mode stress intensity factors. The effect of combined shear and normal traction on the boundary is incorporated in the analysis under the action of gravity. The variation near the crack tip is characterized in terms of the stress intensity factor (SIF) with an aim to find the SIF for a wide range of parameters. The results of the finite element analyses carried out on the compressed disk of a belt pulley arrangement using fracture mechanics concepts are shown. A total of hundred cases of the problem are solved for each of the variations in loading arc parameter and crack orientation using finite element models of the disc under compression. All models were prepared and analyzed for the uncracked disk, disk with a single crack at different orientation emanating from shaft hole as well as for a disc with pair of cracks emerging from the same center hole. Curves are plotted for various loading conditions. Finally, crack propagation paths are determined using kink angle concepts.
Abstract: Investigation of fracture of wood components can prevent from catastrophic failures. Created fracture process zone (FPZ) in crack tip vicinity has important effect on failure of cracked composite materials. In this paper, a failure criterion for fracture investigation of cracked wood specimens under mixed mode I/II loading is presented. This criterion is based on maximum strain energy release rate and material nonlinearity in the vicinity of crack tip due to presence of microcracks. Verification of results with available experimental data proves the coincidence of the proposed criterion with the nature of fracture of wood. To simplify the estimation of nonlinear properties of FPZ, a damage factor is also introduced for engineering and application purposes.
Abstract: In this paper, a linear mixed model which has two
random effects is broken up into two models. This thesis gets
the parameter estimation of the original model and an estimation’s
statistical qualities based on these two models. Then many important
properties are given by comparing this estimation with other general
estimations. At the same time, this paper proves the analysis of
variance estimate (ANOVAE) about σ2 of the original model is equal
to the least-squares estimation (LSE) about σ2 of these two models.
Finally, it also proves that this estimation is better than ANOVAE
under Stein function and special condition in some degree.
Abstract: This paper proposes a linear mixed model (LMM) with spatial effects to forecast rice and cassava yields in Thailand at the same time. A multivariate conditional autoregressive (MCAR) model is assumed to present the spatial effects. A Bayesian method is used for parameter estimation via Gibbs sampling Markov Chain Monte Carlo (MCMC). The model is applied to the rice and cassava yields monthly data which have been extracted from the Office of Agricultural Economics, Ministry of Agriculture and Cooperatives of Thailand. The results show that the proposed model has better performance in most provinces in both fitting part and validation part compared to the simple exponential smoothing and conditional auto regressive models (CAR) from our previous study.
Abstract: This paper proposes a GLMM with spatial and
temporal effects for malaria data in Thailand. A Bayesian method is
used for parameter estimation via Gibbs sampling MCMC. A
conditional autoregressive (CAR) model is assumed to present the
spatial effects. The temporal correlation is presented through the
covariance matrix of the random effects. The malaria quarterly data
have been extracted from the Bureau of Epidemiology, Ministry of
Public Health of Thailand. The factors considered are rainfall and
temperature. The result shows that rainfall and temperature are
positively related to the malaria morbidity rate. The posterior means
of the estimated morbidity rates are used to construct the malaria
maps. The top 5 highest morbidity rates (per 100,000 population) are
in Trat (Q3, 111.70), Chiang Mai (Q3, 104.70), Narathiwat (Q4,
97.69), Chiang Mai (Q2, 88.51), and Chanthaburi (Q3, 86.82).
According to the DIC criterion, the proposed model has a better
performance than the GLMM with spatial effects but without
temporal terms.
Abstract: The work involves develops attended by a numerical
execution of the eXtend Finite Element Method premises a
measurement by the fracture process cracked so many cracked plates
an application will be processed for the calculation of the stress
intensity factor SIF. In the first we give in statically part the
distribution of stress, displacement field and strain of composite plate
in two cases uncrack/edge crack, also in dynamical part the first six
modes shape. Secondly, we calculate Stress Intensity Factor SIF for
different orientation angle θ of central crack with length (2a=0.4mm)
in plan strain condition, KI and KII are obtained for mode I and mode
II respectively using X-FEM method. Finally from crack inclined
involving mixed modes results, the comparison we chose dangerous
inclination and the best crack angle when K is minimal.
Abstract: Leather industry is the most important traditional
industry to provide the leather products in the world for thousand
years. The fierce global competitive environment and common
awareness of global carbon reduction make livestock supply quantities
falling, salt and wet blue leather material reduces and the price
skyrockets significantly. Exchange rate fluctuation led sales revenue
decreasing which due to the differences of export exchanges and
compresses the overall profitability of leather industry. This paper
applies activity-based benefit assessment approach to build up fitness
fur input mixed model, fur is Wet Blue, which concerned with four key
factors: the output rate of wet blue, unit cost of wet blue, yield rate and
grade level of Wet Blue to achieve the low cost strategy under given
unit price of leather product condition of the company. The research
findings indicate that applying this model may improve the input cost
structure, decrease numbers of leather product inventories and to raise
the competitive advantages of the enterprise in the future.
Abstract: Displacement measurement was conducted on compact normal and shear specimens made of acrylic homogeneous material subjected to mixed-mode loading by digital image correlation. The intelligent hybrid method proposed by Nishioka et al. was applied to the stress-strain analysis near the crack tip. The accuracy of stress-intensity factor at the free surface was discussed from the viewpoint of both the experiment and 3-D finite element analysis. The surface images before and after deformation were taken by a CMOS camera, and we developed the system which enabled the real time stress analysis based on digital image correlation and inverse problem analysis. The great portion of processing time of this system was spent on displacement analysis. Then, we tried improvement in speed of this portion. In the case of cracked body, it is also possible to evaluate fracture mechanics parameters such as the J integral, the strain energy release rate, and the stress-intensity factor of mixed-mode. The 9-points elliptic paraboloid approximation could not analyze the displacement of submicron order with high accuracy. The analysis accuracy of displacement was improved considerably by introducing the Newton-Raphson method in consideration of deformation of a subset. The stress-intensity factor was evaluated with high accuracy of less than 1% of the error.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: A device analysis of the photoconductive
semiconductor switch is carried out to investigate distribution of
electric field and carrier concentrations as well as the current density
distribution. The operation of this device was then investigated as a
switch operating in X band. It is shown that despite the presence of
symmetry geometry, switch current density of the on-state steady
state mode is distributed asymmetrically throughout the device.
Abstract: This research investigates risk factors for defective products in autoparts factories. Under a Bayesian framework, a generalized linear mixed model (GLMM) in which the dependent variable, the number of defective products, has a Poisson distribution is adopted. Its performance is compared with the Poisson GLM under a Bayesian framework. The factors considered are production process, machines, and workers. The products coded RT50 are observed. The study found that the Poisson GLMM is more appropriate than the Poisson GLM. For the production Process factor, the highest risk of producing defective products is Process 1, for the Machine factor, the highest risk is Machine 5, and for the Worker factor, the highest risk is Worker 6.
Abstract: Two-dimensional (2D) bar codes were designed to
carry significantly more data with higher information density and
robustness than its 1D counterpart. Thanks to the popular
combination of cameras and mobile phones, it will naturally bring
great commercial value to use the camera phone for 2D bar code
reading. This paper addresses the problem of specific 2D bar code
design for mobile phones and introduces a low-level encoding
method of matrix codes. At the same time, we propose an efficient
scheme for 2D bar codes decoding, of which the effort is put on
solutions of the difficulties introduced by low image quality that is
very common in bar code images taken by a phone camera.
Abstract: In this study the behavior of interlaminar fracture of
carbon-epoxy thermoplastic laminated composite is investigated
numerically and experimentally. Tests are performed with Arcan
specimens. Testing with Arcan specimen gives the opportunity of
utilizing just one kind of specimen for extracting fracture properties
for mode I, mode II and different mixed mode ratios of materials with
exerting load via different loading angles. Variation of loading angles
in range of 0-90° made possible to achieve different mixed mode
ratios. Correction factors for various conditions are obtained from
ABAQUS 2D finite element models which demonstrate the finite
shape of Arcan specimens used in this study. Finally, applying the
correction factors to critical loads obtained experimentally, critical
interlaminar fracture toughness of this type of carbon- epoxy
composite has been attained.
Abstract: The modified Arcan fixture was used in order to
investigate the mixed mode fracture properties of high strength steel
butt weld through experimental and numerical analysis. The fixture
consisted of a central section with "butterfly-shaped" specimen that
had central crack. The specimens were under pure mode I (opening),
pure mode II (shearing) and all in plane mixed mode loading angles
starting from 0 to 90 degrees. The geometric calibration factors were
calculated with the aid of finite element analysis for various loading
mode and different crack length (0.45≤ a/w ≤0.55) and the critical
fracture loads obtained experimentally. The critical fracture
toughness (KIC & KIIC) estimated with experimental and numerical
analysis under mixed mode loading conditions.
Abstract: In this study the mixed mode fracture mechanics
parameters were investigated for high tensile steel butt welded joint
based on modified Arcan test and finite element analysis was used to
evaluate the effect of crack length on fracture criterion. The nondimensional
stress intensity factors, strain energy release rates and Jintegral
energy on crack tip were obtained for various in-plane
loading combinations on Arcan specimen starting from pure mode-I
to pure mode-II loading conditions. The specimen and apparatus were
modeled by finite element method and analyzed under various
loading angles (between 0 to 90 degrees with 15 degree interval) to
simulate the pure mode-I, II and mixed mode fracture. Since the
analytical results are independent from elasticity modules for
isotropic materials, therefore the results in elastic fields can be used
for Arcan specimens. The main objective of this study was to
evaluate the geometric calibration factors for modified Arcan test
specimen in order to obtain fracture toughness under mixed mode
loading conditions.
Abstract: Data on 657 lactation from 163 Maltese goat,
collected over a 5-year period were analyzed by a mixed model to
estimate the variance components for heritability. The considered
lactation traits were: milk yield (MY) and lactation length (LL). Year,
parity and type of birth (single or twin) were significant sources of
variation for lactation length; on the other hand milk yield was
significantly influenced only by the year. The average MY was
352.34 kg and the average LL was 230 days. Estimates of heritability
were 0.21 and 0.15 for MY and LL respectively. These values
suggest there is low correlation between genotype and phenotype so
it may be difficult to evaluate animals directly on phenotype. So, the
genetic improvement of this breed may be quite slow without the
support of progeny test aimed to select Maltese breeders.
Abstract: Mixed Model Production is the practice of assembling
several distinct and different models of a product on the same
assembly line without changeovers and then sequencing those models
in a way that smoothes the demand for upstream components. In this
paper, we consider an objective function which minimizes total
stoppage time and total idle time and it is presented sequence
dependent set up time. Many studies have been done on the mixed
model assembly lines. But in this paper we specifically focused on
reducing the idle times. This is possible through various help policies.
For improving the solutions, some cases developed and about 40 tests
problem was considered. We use scatter search for optimization and
for showing the efficiency of our algorithm, experimental results
shows behavior of method. Scatter search and help policies can
produce high quality answers, so it has been used in this paper.
Abstract: Data from 1731 Gentile di Puglia lambs, sired by 65 rams over a 5-year period were analyzed by a mixed model to estimate the variance components for heritability. The considered growth traits were: birth weight (BW), weight at 30 days of age (W30) and average daily gain from birth to 30 days of age (DG). Year of birth, sex of lamb, type of birth (single or twin), dam age at lambing and farm were significant sources of variation for all the considered growth traits. The average lamb weights were 3.85±0.16 kg at birth, 9.57±0.91 kg at 30 days of age and the average daily gain was 191±14 g. Estimates of heritability were 0.33±0.05, 0.41±0.06 and 0.16±0.05 respectively for the same traits. These values suggest there is a good opportunity to improve Gentile di Puglia lambs by selecting animals for growth traits.
Abstract: A current mirror (CM) based on self cascode MOSFETs low voltage analog and mixed mode structures has been proposed. The proposed CM has high output impedance and can operate at 0.5 V. P-Spice simulations confirm the high performance of this CM with a bandwidth of 6.0 GHz at input current of 100 μA.