Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: There is an increasing demand for broadband services
in Indonesia. Therefore, the answer is the use of Ka-Band which has
some advantages such as wider bandwidth, the higher transmission
speeds, and smaller size of antenna in the ground. However, rain
attenuation is the primary factor in the degradation of signal at the
Kaband. In this paper, the author will determine whether the Ka-band
frequency can be implemented in Indonesia which has high intensity
of rainfall.
Abstract: In this paper, the design of a coaxial feed single layer rectangular microstrip patch antenna for three different wireless communication band applications is presented. The proposed antenna is designed by using substrate Roger RT/duroid 5880 having permittivity of about 2.2 and tangent loss of 0.0009. The characteristics of the substrate are designed and to evaluate the performance of modeled antenna using HFSS v.11 EM simulator, from Ansoft. The proposed antenna has small in size and operates at 2.25GHz, 3.76GHz and 5.23GHz suitable for mobile satellite service (MSS) network, WiMAX and WLAN applications. The dimension of the patch and slots are optimized to obtain these desired functional frequency ranges. The simulation results with frequency response, radiation pattern and return loss, VSWR, Input Impedance are presented with appropriate table and graph.
Abstract: Wireless communications have been expanded very fast in recent decades. This technology relies on an extensive network of base stations and antennas, using radio frequency signals to transmit information. Devices that use wireless communication, while offering various services, basically act as sources of non-ionizing electromagnetic fields (EMF). Such devices are permanently present in human vicinity and almost constantly radiate, causing EMF pollution of the environment. This fact has initiated development of modern systems for observation of the EMF pollution, as well as for risk assessment. This paper presents the Serbian electromagnetic field monitoring network – SEMONT, designed for automated, remote and continuous broadband monitoring of EMF in the environment. Measurement results of the SEMONT monitoring at one of the test locations, within the main campus of the University of Novi Sad, are presented and discussed, along with corresponding exposure assessment of the general population, regarding the Serbian legislation.
Abstract: In this paper, a fifth order propagator operators are proposed for estimating the Angles Of Arrival (AOA) of narrowband electromagnetic waves impinging on antenna array when its number of sensors is larger than the number of radiating sources.
The array response matrix is partitioned into five linearly dependent phases to construct the noise projector using five different propagators from non diagonal blocks of the spectral matrice of the received data; hence, five different estimators are proposed to estimate the angles of the sources. The simulation results proved the performance of the proposed estimators in the presence of white noise comparatively to high resolution eigen based spectra.
Abstract: In this paper the design, fabrication, and testing of a miniaturized rectangular microstrip patch antenna loaded with DNG metamaterials is reported. The metamaterial is composed of two nested spiral strips and a single straight strip which are etched on two sides of a 5.7 mm×5.7 mm Rogers RT/duroid 5880 with 0.5 mm thickness and dielectric constant of 2.2. Two units of this structure as a double negative (DNG) medium in combination with air as a double positive (DPS) medium are used as substrate of the microstrip patch antenna. By placing these metamaterial structures under the patch, a sub-wavelength resonance occurs which leads to a smaller size patch antenna compared to the conventional antenna at that frequency. The total size of the proposed antenna is reduced 54.6%. The dimensions of the proposed patch antenna are significantly smaller than the wavelength of the operation frequency with respect to the conventional patch antenna. Simulation result and test result for the proposed patch antenna are given and compared.
Abstract: This paper increases directivity and gain of Small Planar Dipole Antenna (SPDA) by using Symmetrical Pyramidal Block (SPB) which operates in X band at 11 GHz. The SPB consists four sides; each of which is metamaterial with Epsilon Negative Medium (ENG) and Epsilon Near-Zero (ENZ). The results simulated using the High Frequency Structure Simulator (HFSS) show that the SPB is capable of enhancing directivity and gain for the SPDA with maximum gain of 2.46 dB. The reflection coefficient is -13.7037 dB with narrow beam width.
Abstract: This paper presents breast cancer detection by
observing the specific absorption rate (SAR) intensity for
identification tumor location, the tumor is identified in coordinates
(x,y,z) system. We examined the frequency between 4-8 GHz to look
for the most appropriate frequency. Results are simulated in
frequency 4-8 GHz, the model overview include normal breast with
50 mm radian, 5 mm diameter of tumor, and ultra wideband (UWB)
bowtie antenna. The models are created and simulated in CST
Microwave Studio. For this simulation, we changed antenna to 5
location around the breast, the tumor can be detected when an
antenna is close to the tumor location, which the coordinate of
maximum SAR is approximated the tumor location. For reliable, we
experiment by random tumor location to 3 position in the same size
of tumor and simulation the result again by varying the antenna
position in 5 position again, and it also detectable the tumor position
from the antenna that nearby tumor position by maximum value of
SAR, which it can be detected the tumor with precision in all
frequency between 4-8 GHz.
Abstract: To avoid battery assisted tags with limited lifetime batteries, it is proposed here to replace them by energy harvesting
systems, able to feed from local environment. This would allow total
independence to RFID systems, very interesting for applications
where tag removal from its location is not possible. Example is here
described for luggage safety in airports, and is easily extendable to similar situation in terms of operation constraints. The idea is to fix
RFID tag with energy harvesting system not only to identify luggage
but also to supply an embedded microcontroller with a sensor
delivering luggage weight making it impossible to add or to remove
anything from the luggage during transit phases. The aim is to
optimize the harvested energy for such RFID applications, and to
study in which limits these applications are theoretically possible.
Proposed energy harvester is based on two energy sources:
piezoelectricity and electromagnetic waves, so that when the luggage
is moving on ground transportation to airline counters, the piezo
module supplies the tag and its microcontroller, while the RF module
operates during luggage transit thanks to readers located along the
way. Tag location on the luggage is analyzed to get best vibrations, as
well as harvester better choice for optimizing the energy supply
depending on applications and the amount of energy harvested during
a period of time. Effects of system parameters (RFID UHF
frequencies, limit distance between the tag and the antenna necessary
to harvest energy, produced voltage and voltage threshold) are
discussed and working conditions for such system are delimited.
Abstract: This paper presents the gain improvement of a sector antenna for mobile phone base station by using the new technique to enhance its gain for microstrip antenna (MSA) array without construction enlargement. The curved woodpile Electromagnetic Band Gap (EBG) has been utilized to improve the gain instead. The advantages of this proposed antenna are reducing the length of MSAs array but providing the higher gain and easy fabrication and installation. Moreover, it provides a fan-shaped radiation pattern, wide in the horizontal direction and relatively narrow in the vertical direction, which appropriate for mobile phone base station. The paper also presents the design procedures of a 1x8 MSAs array associated with U-shaped reflector for decreasing their back and side lobes. The fabricated curved woodpile EBG exhibits bandgap characteristics at 2.1 GHz and is utilized for realizing a resonant cavity of MSAs array. This idea has been verified by both the Computer Simulation Technology (CST) software and experimental results. As the results, the fabricated proposed antenna achieves a high gain of 20.3 dB and the half-power beam widths in the E- and H-plane of 36.8 and 8.7 degrees, respectively. Good qualitative agreement between measured and simulated results of the proposed antenna was obtained.
Abstract: The conventional rectangular horn has been used for microwave antenna a long time. Its gain can be increased by enlarging the construction of horn to flare exponentially. This paper presents a study of the shaped woodpile Electromagnetic Band Gap (EBG) to improve its gain for conventional horn without construction enlargement. The gain enhancement synthesis method for shaped woodpile EBG that has to transfer the electromagnetic fields from aperture of a horn antenna through woodpile EBG is presented by using the variety of shaped woodpile EBGs such as planar, triangular, quadratic, circular, gaussian, cosine, and squared cosine structures. The proposed technique has the advantages of low profile, low cost for fabrication and light weight. The antenna characteristics such as reflection coefficient (S11), radiation patterns and gain are simulated by utilized A Computer Simulation Technology (CST) software. With the proposed concept, an antenna prototype was fabricated and experimented. The S11 and radiation patterns obtained from measurements show a good impedance matching and a gain enhancement of the proposed antenna. The gain at dominant frequency of 10 GHz is 25.6 dB, application for X- and Ku-Band Radar, that higher than the gain of the basic rectangular horn antenna around 8 dB with adding only one appropriated EBG structures.
Abstract: This paper proposes the development and design of
double layer metamaterials based on electromagnetic band gap
(EBG) rods as a superstrate of a resonator antenna to enhance
required antenna characteristics for the mobile base station. The
metallic rod type metamaterial can partially reflect wave of a primary
radiator. The antenna was designed and analyzed by a simulation
result from CST Microwave Studio and designed technique could be
confirmed by a measurement results from prototype antenna that
agree with simulation results. The results indicate that the antenna
can also generate a dual polarization by using a 45˚ oriented curved
strip dipole located at the center of the reflector plane with double
layer superstrate. It can be used to simplify the feed system of an
antenna. The proposed antenna has a bandwidth covering the
frequency range of 1920 – 2200 MHz, the gain of the antenna
increases up to 14.06 dBi. In addition, an interesting sectoral 60˚
pattern is presented in horizontal plane.
Abstract: This paper describes a node pair selection scheme
in relay-aided multiple source multiple destination communication
system based on stable marriage problem. A general case is assumed
in which all of source, relay and destination nodes are equipped
with multiantenna and carry out multistream transmission. Based
on several metrics introduced from inter-node channel condition,
the preference order is determined about all source-relay and
relay-destination relations, and then the node pairs are determined
using Gale-Shapley algorithm. The computer simulations show
that the effectiveness of node pair selection is larger in multihop
communication. Some additional aspects which are different from
relay-less case are also investigated.
Abstract: In this paper, the design of a coaxial feed single layer rectangular microstrip patch antenna for IEEE802.11b application is presented. The proposed antenna is designed by using substrate FR4_epoxy having permittivity of about 4.4 and tangent loss of 0.013. The characteristics of the substrate are designed and to evaluate the performance of modeled antenna using HFSS v.11 EM simulator, from Ansoft. The proposed antenna dual resonant frequency has been achieved in the band of 1.57GHz-1.68GHz (with BW 30 MHz) and 2.25 GHz -2.55GHz (with BW 40MHz). The simulation results with frequency response, radiation pattern and return loss, VSWR, Input Impedance are presented with appropriate table and graph.
Abstract: This paper presents a novel CPW fed patch antenna supporting a wide band from 2.7 GHz – 6.5 GHz. The antenna is compact with size 32 x 30 x 1.6mm3, built over FR4-epoxy substrate (εr=4.4). Bandwidth enhancement has been achieved by using the concept of modified ground structure (MGS). For this purpose structural design has been optimized by parametric simulations in CST MWS. The proposed antenna can perform well in variety of wireless communication services including 5.15 GHz- 5.35 GHz and 5.725 GHz- 5.825 GHz WLAN IEEE 802.11 g/a, 5.2/ 5.5/ 5.8 GHz Wi-Fi, 3.5/5.5 GHz WiMax applications and 3.7 - 4.2 GHz C band satellite communications bands. The measured experimental results show that bandwidth (S11 < -10 dB) of antenna is 3.8 GHz. The performance of antenna is studied in terms of reflection coefficient, radiation characteristics, current distribution and gain.
Abstract: Cooperative communication provides transmit diversity, even when, due to size constraints, mobile units cannot accommodate multiple antennas. A versatile cooperation method called coded cooperation has been developed, in which cooperation is implemented through channel coding with a view to controlling the errors inherent in wireless communication. In this work we evaluate the performance of coded cooperation in flat Rayleigh fading environment using a concept known as the pair wise error probability (PEP). We derive the PEP for a flat fading scenario in coded cooperation and then compare with the signal-to-noise ratio of the users in the network. Results show that an increase in the SNR leads to a decrease in the PEP. We also carried out simulations to validate the result.
Abstract: Narrow bandwidth and high loss performance limits the use of reflectarray antennas in some applications. This article reports on the feasibility of employing strategic reflectarray resonant elements to characterize the reflectivity performance of reflectarrays in X-band frequency range. Strategic reflectarray resonant elements incorporating variable substrate thicknesses ranging from 0.016λ to 0.052λ have been analyzed in terms of reflection loss and reflection phase performance. The effect of substrate thickness has been validated by using waveguide scattering parameter technique. It has been demonstrated that as the substrate thickness is increased from 0.508mm to 1.57mm the measured reflection loss of dipole element decreased from 5.66dB to 3.70dB with increment in 10% bandwidth of 39MHz to 64MHz. Similarly the measured reflection loss of triangular loop element is decreased from 20.25dB to 7.02dB with an increment in 10% bandwidth of 12MHz to 23MHz. The results also show a significant decrease in the slope of reflection phase curve as well. A Figure of Merit (FoM) has also been defined for the comparison of static phase range of resonant elements under consideration. Moreover, a novel numerical model based on analytical equations has been established incorporating the material properties of dielectric substrate and electrical properties of different reflectarray resonant elements to obtain the progressive phase distribution for each individual reflectarray resonant element.
Abstract: Cooperative communication systems are considered to be a promising technology to improve the system capacity, reliability and performances over fading wireless channels. Cooperative relaying system with a single antenna will be able to reach the advantages of multiple antenna communication systems. It is ideally suitable for the distributed communication systems; the relays can cooperate and form virtual MIMO systems. Thus the paper will aim to investigate the possible enhancement of cooperated system using decode and forward protocol. On the decode and forward an attempt to cancel or at least reduce the interference instead of increasing the SNR values is achieved. The latter can be achieved via the use group of relays depending on the channel status from source to relay and relay to destination respectively.
In the proposed system, the transmission time has been divided into two phases to be used by the decode and forward protocol. The first phase has been allocated for the source to transmit its data whereas the relays and destination nodes are in receiving mode. On the other hand, the second phase is allocated for the first and second groups of relay nodes to relay the data to the destination node. Simulations results have shown an improvement in performance is achieved compared to the conventional decode and forward in terms of BER and transmission rate.
Abstract: This paper focuses on the analysis of Nanoptenna for extreme fast communication. The Nanoptenna is basically a nano antenna designed for communication at optical range of frequencies. Since, this range of frequencies includes the visible spectrum of the light, so there is a high possibility of the data transfer at high rates and extreme fast communication (XFC). The shape chosen for the analysis is a bow tie structure due to its various characteristics of electric field enhancement.