Abstract: The present study addresses the problem of ammonia evaporation during filling of a vertical cylindrical tank and the influence of various external factors on the stability of storage by determining the conditions for minimum evaporation. Numerical simulation is carried out by solving the governing equations namely, continuity, momentum, energy, and diffusion of species. The effect of temperature of surrounding air, the filling speed of the reservoir and the temperature of the filling liquid ammonia on the evaporation rate is investigated. Results show that the temperature of the filling liquid has little effect on the liquid ammonia for a short period, which, in fact, is function of the filling speed. The evaporation rate along the free surface of the liquid is non-uniform. The inlet temperature affects the vapor ammonia temperature because of pressure increase. The temperature of the surrounding air affects the temperature of the vapor phase rather than the liquid phase. The maximum of evaporation is reached at the final step of filling. In order to minimize loss of ammonia vapors automatically causing losses in quantity of the liquid stored, it is suggested to ensure the proper insulation for the walls and roof of the reservoir and to increase the filling speed.
Abstract: CO2 capture and storage technologies play a significant role in contributing to the control of climate change through the reduction of carbon dioxide emissions into the atmosphere. The present study evaluates and optimizes CO2 capture through a process, where carbon dioxide is passed into pH adjusted high salinity water and reacted with sodium chloride to form a precipitate of sodium bicarbonate. This process is based on a modified Solvay process with higher CO2 capture efficiency, higher sodium removal, and higher pH level without the use of ammonia. The process was tested in a bubble column semi-batch reactor and was optimized using response surface methodology (RSM). CO2 capture efficiency and sodium removal were optimized in terms of major operating parameters based on four levels and variables in Central Composite Design (CCD). The operating parameters were gas flow rate (0.5–1.5 L/min), reactor temperature (10 to 50 oC), buffer concentration (0.2-2.6%) and water salinity (25-197 g NaCl/L). The experimental data were fitted to a second-order polynomial using multiple regression and analyzed using analysis of variance (ANOVA). The optimum values of the selected variables were obtained using response optimizer. The optimum conditions were tested experimentally using desalination reject brine with salinity ranging from 65,000 to 75,000 mg/L. The CO2 capture efficiency in 180 min was 99% and the maximum sodium removal was 35%. The experimental and predicted values were within 95% confidence interval, which demonstrates that the developed model can successfully predict the capture efficiency and sodium removal using the modified Solvay method.
Abstract: The exploitation of gold ore deposits is highly dependent on efficient mineral processing methods, although actual perspectives based on life-cycle assessment introduce difficulties that were unforeseen in a very recent past. Cyanidation is the most applied gold processing method, but the potential environmental problems derived from the usage of cyanide as leaching reagent led to a demand for alternative methods. Ammoniacal thiosulfate leaching is one of the most important alternatives to cyanidation. In this article, some experimental studies carried out in order to assess the feasibility of thiosulfate as a leaching agent for the ore from the unexploited Portuguese gold mine of Castromil. It became clear that the process depends on the concentrations of ammonia, thiosulfate and copper. Based on this fact, a few leaching tests were performed in order to assess the best reagent prescription, and also the effects of different combination of these concentrations. Higher thiosulfate concentrations cause the decrease of gold dissolution. Lower concentrations of ammonia require higher thiosulfate concentrations, and higher ammonia concentrations require lower thiosulfate concentrations. The addition of copper increases the gold dissolution ratio. Subsequently, some alternative operatory conditions were tested such as variations in temperature and in the solid/liquid ratio as well as the application of a pre-treatment before the leaching stage. Finally, thiosulfate leaching was compared to cyanidation. Thiosulfate leaching showed to be an important alternative, although a pre-treatment is required to increase the yield of the gold dissolution.
Abstract: In this paper, we present a portable ammonia gas detector for performing the gas safety management efficiently. The display of the detector is separated from its body. The display module is received the data measured from the detector using ZigBee. The detector has a rechargeable li-ion battery which can be use for 11~12 hours, and a Bluetooth module for sending the data to the PC or the smart devices. The data are sent to the server and can access using the web browser or mobile application. The range of the detection concentration is 0~100ppm.
Abstract: This study involves the modeling and monitoring of an ammonia synthesis fixed-bed reactor using partial least squares (PLS) and its variants. The process exhibits complex dynamic behavior due to the presence of heat recycling and feed quench. One limitation of static PLS model in this situation is that it does not take account of the process dynamics and hence dynamic PLS was used. Although it showed, superior performance to static PLS in terms of prediction, the monitoring scheme was inappropriate hence adaptive PLS was considered. A limitation of adaptive PLS is that non-conforming observations also contribute to the model, therefore, a new adaptive approach was developed, robust adaptive dynamic PLS. This approach updates a dynamic PLS model and is robust to non-representative data. The developed methodology showed a clear improvement over existing approaches in terms of the modeling of the reactor and the detection of faults.
Abstract: In this work, our goal is to optimize the nitriding treatment at a low-temperature of the steel 32CrMoV13 using gas mixtures of ammonia, nitrogen and hydrogen to improve the mechanical properties of the surface (good wear resistance, friction and corrosion), and of the diffusion layer of the nitrogen (good resistance to fatigue and good tenacity with heart). By limiting our work to the pure iron and to the alloys iron-chromium and iron-chromium-carbon, we have studied the various parameters which manage the nitriding: flow rate and composition of the gaseous phase, the interaction chromium-nitrogen and chromium-carbon by the help of experiments of nitriding realized in the laboratory by thermogravimetry. The acquired knowledge has been applied by the mastery of the growth of the γ' combination layer on the α diffusion layer in the case of the industrial steel 32CrMoV13.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: Industries produce millions of cubic meters of effluent
every year and the wastewater produced may be released into the
surrounding water bodies, treated on-site or at municipal treatment
plants. The determination of organic matter in the wastewater
generated is very important to avoid any negative effect on the
aquatic ecosystem. The scope of the present work is to assess the
physicochemical composition of the wastewater produced from one
of the brewery industry in South Africa. This is to estimate the
environmental impact of its discharge into the receiving water bodies
or the municipal treatment plant. The parameters monitored for the
quantitative analysis of brewery wastewater include biological
oxygen demand (BOD5), chemical oxygen demand (COD), total
suspended solids, volatile suspended solids, ammonia, total oxidized
nitrogen, nitrate, nitrite, phosphorus and alkalinity content. In
average, the COD concentration of the brewery effluent was 5340.97
mg/l with average pH values of 4.0 to 6.7. The BOD5 and the solids
content of the wastewater from the brewery industry were high. This
means that the effluent is very rich in organic content and its
discharge into the water bodies or the municipal treatment plant could
cause environmental pollution or damage the treatment plant. In
addition, there were variations in the wastewater composition
throughout the monitoring period. This might be as a result of
different activities that take place during the production process, as
well as the effects of peak period of beer production on the water
usage.
Abstract: The goal of this experiment is to evaluate the
effectiveness of different leachate pre-treatment options in terms of
COD and ammonia removal. This research focused on the evaluation
of physical-chemical methods for pre-treatment of leachate that
would be effective and rapid in order to satisfy the requirements of
the sewer discharge by-laws. The four pre-treatment options
evaluated were: air stripping, chemical coagulation, electrocoagulation
and advanced oxidation with sodium ferrate. Chemical
coagulation reported the best COD removal rate at 43%, compared to
18% for both air stripping and electro-coagulation, and 20% for
oxidation with sodium ferrate. On the other hand, air stripping was
far superior to the other treatment options in terms of ammonia
removal with 86%. Oxidation with sodium ferrate reached only 16%,
while chemical coagulation and electro-coagulation removed less
than 10%. When combined, air stripping and chemical coagulation
removed up to 50% COD and 85% ammonia.
Abstract: SARA is a common and serious metabolic disorder in
early lactation in dairy cattle and in finishing beef cattle, caused by
diets with high inclusion of cereal grain. This experiment was
performed to determine the efficacy of Megasphaera elsdenii, a
major lactate-utilizing bacterium in prevention/treatment of SARA in
vivo. In vivo experimentation, it was used eight ruminally cannulated
rams and it was applied the rapid adaptation with the mixture of grain
based on wheat (80% wheat, 20% barley) and barley (80% barley,
20% wheat). During the systematic adaptation, it was followed the
probability of SARA formation by being measured the rumen pH
with two hours intervals after and before feeding. After being
evaluated the data, it was determined the ruminal pH ranged from
5.2-5.6 on the condition of feeding with 60 percentage of grain
mixture based on barley and wheat, that assured the definite form of
subacute acidosis. In four days SARA period, M. elsdenii (1010 cfu
ml-1) was inoculated during the first two days. During the SARA
period, it was observed the decrease of feed intake with M. elsdenii
inoculation. Inoculation of M. elsdenii was caused to differentiation
of rumen pH (P
Abstract: This paper presents powerful techniques for the
development of a new monitoring method based on multi-scale
entropy (MSE) in order to characterize the behaviour of the
concentrations of different gases present in the synthesis of Ammonia
and soft-sensor based on Principal Component Analysis (PCA).
Abstract: The absorption power generation cycle based on the
ammonia-water mixture has attracted much attention for efficient
recovery of low-grade energy sources. In this paper a thermodynamic
performance analysis is carried out for a Kalina cycle using
ammonia-water mixture as a working fluid for efficient conversion of
low-temperature heat source in the form of sensible energy. The
effects of the source temperature on the system performance are
extensively investigated by using the thermodynamic models. The
results show that the source temperature as well as the ammonia mass
fraction affects greatly on the thermodynamic performance of the
cycle.
Abstract: The aim of present study was to monitor the presence
of Trichodina sp. in Rainbow trout, Oncorhynchus mykiss collected
from various fish farms in the western provinces of Iran during
January, 2013- January, 2014. Out of 675 sampled fish 335, (49.16%)
were infested with Trichodina. The highest prevalence was observed
in the spring and winter followed by autumn and summer. In general,
the intensity of infection was low except in cases where outbreaks of
Trichodiniasis endangered the survival of fish in some ponds. In light
infestation Trichodina is usually present on gills, fins and skin of
apparently healthy fish. Clinical signs of Trichodiniasis only appear
on fish with heavy infections and cases of moderate ones that are
usually exposed to one or more stress factors including, rough
handling during transportation from ponds, overcrowdness,
malnutrition, high of free ammonia and low of oxygen concentration.
Clinical signs of Trichodiniasis in sampled fish were sluggish
movement, loss of appetite, black coloration, necrosis and ulcer on
different parts of the body, detached scales and excessive
accumulation of mucous in gill pouches. The most obvious
histopathological changes in diseased fish were sloughing of the
epidermal layer, aggregation of leucocytes and melanine-carrying
cells (between the dermis and hypodermis) and proliferative changes
including hyperplasia and hypertrophy of the epithelial lining cells of
gill filaments which resulted in fusion of secondary lamellae. Control
of Trichodiniasis, has been achieved by formalin bath treatment at a
concentration of 250 ppm for one hour.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: Local utilities often face problems of local industrial
wastes, storm water disposal due to existing strict regulations. For
many local industries, the problem of wastewater treatment and
discharge into surface reservoirs can’t be solved through the use of
conventional biological treatment techniques. Current discharge
standards require very strict removal of a number of impurities such
as ammonia, nitrates, phosphate, etc. To reach this level of removal,
expensive reagents and sorbents are used.
The modern concept of rational water resources management
requires the development of new efficient techniques that provide
wastewater treatment and reuse.
As RO membranes simultaneously reject all dissolved impurities
such as BOD, TDS, ammonia, phosphates etc., they become very
attractive for the direct treatment of wastewater without biological
stage. To treat wastewater, specially designed membrane "open
channel" modules are used that do not possess "dead areas" that cause
fouling or require pretreatment. A solution to RO concentrate
disposal problem is presented that consists of reducing of initial
wastewater volume by 100 times. Concentrate is withdrawn from
membrane unit as sludge moisture. The efficient use of membrane
RO techniques is connected with a salt balance in water system.
Thus, to provide high ecological efficiency of developed techniques,
all components of water supply and wastewater discharge systems
should be accounted for.
Abstract: This paper carries out a performance analysis based on
the first and second laws of thermodynamics for heat recovery vapor
generator (HRVG) of ammonia-water mixture when the heat source is
low-temperature energy in the form of sensible heat. In the analysis,
effects of the ammonia mass concentration and mass flow ratio of the
binary mixture are investigated on the system performance including
the effectiveness of heat transfer, entropy generation, and exergy
efficiency. The results show that the ammonia concentration and the
mass flow ratio of the mixture have significant effects on the system
performance of HRVG.
Abstract: Ammonium nitrate (AN) is produced by the reaction of ammonia and nitric acid, and a waste condensate is obtained. The condensate contains pure AN in concentration up to 10g/L. The salt content in the condensate is too high to discharge immediately into the river thus it must be treated. This study is concerned with the treatment of condensates from an industrial AN production by combination of electrodialysis (ED) and electrodeionization (EDI). The condensate concentration was in range 1.9–2.5g/L of AN. A pilot ED module with 25 membrane pairs following by a laboratory EDI module with 10 membrane pairs operated continuously during 800 hours. Results confirmed that the combination of ED and EDI is suitable for the condensate treatment.
Abstract: In the era of sustainability, utilization of livestock wastes as soil amendment to provide micronutrients for crops is very economical and sustainable. It is well understood that livestock wastes are comparable, if not better, nutrient sources for crops as chemical fertilizers. However, the large concentrated volumes of animal manure produced from livestock operations and the limited amount of available nearby agricultural land areas necessitated the need for volume reduction of these animal wastes. Composting of these animal manures is a viable option for biomass and pathogenic reduction in the environment. Nevertheless, composting also increases the potential loss of available nutrients for crop production as well as unwanted emission of anthropogenic air pollutants due to the loss of ammonia and other compounds via volatilization. In this study, we examine the emission of ammonia and nitrous oxide from swine manure windrows to evaluate the benefit of biomass reduction in conjunction with the potential loss of available nutrients. The feedstock for the windrows was obtained from swine farm in Kentucky where swine manure was mixed with wood shaving as absorbent material. Static flux chambers along with photoacoustic gas analyzer were used to monitor ammonia and nitrous oxide concentrations during the composting process. The results show that ammonia and nitrous oxide fluxes were quite high during the initial composting process and after the turning of each compost pile. Over the period of roughly three months of composting, the biochemical oxygen demand (BOD) decreased by about 90%. Although composting of animal waste is quite beneficial for biomass reduction, composting may not be economically feasible from an agronomical point of view due to time, nutrient loss (N loss), and potential environmental pollution (ammonia and greenhouse gas emissions). Therefore, additional studies are needed to assess and validate the economics and environmental impact of animal (swine) manure composting (e.g., crop yield or impact on climate change).
Abstract: The paper represents the dependence of ammonia concentration on microclimate parameters and photocopying shop circulation. The concentration of ammonia was determined during 8-hours working time over five days including three sampling points of a photocopying shop in Novi Sad, Serbia. The obtained results pointed out that the room temperature possesses the highest impact on ammonia release. The obtained ammonia concentration was in the range of 1.53 to 0.42ppm and decreased with the temperature decreasing from 24.6 to 20.7oC. As the detected concentrations were within the permissible levels of The Occupational Safety and Health Administration, The National Institute for Occupational Safety and The Health and Official Gazette of Republic of Serbia, in the range of 35 to 200ppm, there was no danger to the employee’s health in the photocopying shop.
Abstract: Coagulation is a process that sanitizes leather effluents. It aims to reduce pollutants such as Chemical Oxygen Demand (COD), chloride, sulfate, chromium, suspended solids, and other dissolved solids. The current study aimed to evaluate coagulation efficiency of tannery wastewater by analyzing the change in organic matter, odor, color, ammonium ions, nutrients, chloride, H2S, sulfate, suspended solids, total dissolved solids, fecal pollution, and chromium hexavalent before and after treatment. Effluent samples were treated with coagulants Ca(OH)2 and FeSO4 .7H2O. The best advantages of this treatment included the removal of: COD (81.60%); ammonia ions (98.34%); nitrate ions (92%); chromium hexavalent (75.00%); phosphate (70.00%); chloride (69.20%); and H₂S (50%). Results also indicated a high level of efficiency in the reduction of fecal pollution indicators. Unfortunately, only a modest reduction of sulfate (19.00%) and TSS (13.00%) and an increase in TDS (15.60%) was observed.