Abstract: A closed-loop controlled wireless power transmission circuit block for implantable biomedical applications is described in this paper. The circuit consists of one front-end rectifier, power management sub-block including bandgap reference and low drop-out regulators (LDOs) as well as transmission power detection / feedback circuits. Simulation result shows that the front-end rectifier achieves 80% power efficiency with 750-mV single-end peak-to-peak input voltage and 1.28-V output voltage under load current of 4 mA. The power management block can supply 1.8mA average load current under 1V consuming only 12μW power, which is equivalent to 99.3% power efficiency. The wireless power transmission block described in this paper achieves a maximum power efficiency of 80%. The wireless power transmission circuit block is designed and implemented using UMC 65-nm CMOS/RF process. It occupies 1 mm × 1.2 mm silicon area.
Abstract: Functional Magnetic Resonance Imaging(fMRI) is a
noninvasive imaging technique that measures the hemodynamic
response related to neural activity in the human brain. Event-related
functional magnetic resonance imaging (efMRI) is a form of
functional Magnetic Resonance Imaging (fMRI) in which a series of
fMRI images are time-locked to a stimulus presentation and averaged
together over many trials. Again an event related potential (ERP) is a
measured brain response that is directly the result of a thought or
perception. Here the neuronal response of human visual cortex in
normal healthy patients have been studied. The patients were asked
to perform a visual three choice reaction task; from the relative
response of each patient corresponding neuronal activity in visual
cortex was imaged. The average number of neurons in the adult
human primary visual cortex, in each hemisphere has been estimated
at around 140 million. Statistical analysis of this experiment was
done with SPM5(Statistical Parametric Mapping version 5) software.
The result shows a robust design of imaging the neuronal activity of
human visual cortex.
Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: Experimental investigation has been carried out
towards understanding the complex fluid dynamics involved in the
interaction of vortical structures with zero pressure gradient boundary
layer. A laminar boundary layer is produced on the flat plate placed
in the water flume and the synthetic jet actuator is deployed on top of
the plate at a definite distance from the leading edge. The synthetic
jet actuator has been designed in such a way that the to and fro
motion of the diaphragm is maneuvered at will by varying the
operating parameters to produce the typical streamwise vortical
structures namely hairpin and tilted vortices. PIV measurements are
made on the streamwise plane normal to the plate to evaluate their
interaction with the near wall fluid.
Abstract: An improved processing description to be employed in biosonar signal processing in a cochlea model is proposed and examined. It is compared to conventional models using a modified discrimination analysis and both are tested. Their performances are evaluated with echo data captured from natural targets (trees).Results indicate that the phase characteristics of low-pass filters employed in the echo processing have a significant effect on class separability for this data.
Abstract: Our research aims at helping the tutor on line to
evaluate the student-s cognitive processes. The student is a learner in
French as a Second Language who studies an on-line socio-cognitive
scenario in written communication. In our method, these cognitive
processes are defined. For that, the language abilities and learning
tasks are associated to cognitive operation. Moreover, the found
cognitive processes are named with specific terms. The result was to
create an instrumental pattern to question the learner about the
cognitive processes used to build an item of written comprehension.
Our research follows the principles of the third historical generation
of studies on the cognitive activity of the text comprehension. The
strength of our instrumental pattern stands in the precision and the
logical articulation of the questions to the learner. However, the
learner-s answers can still be subjective but the precision of the
instrument restricts it.
Abstract: Mammography is the most effective procedure for an
early diagnosis of the breast cancer. Nowadays, people are trying to
find a way or method to support as much as possible to the
radiologists in diagnosis process. The most popular way is now being
developed is using Computer-Aided Detection (CAD) system to
process the digital mammograms and prompt the suspicious region to
radiologist. In this paper, an automated CAD system for detection
and classification of massive lesions in mammographic images is
presented. The system consists of three processing steps: Regions-Of-
Interest detection, feature extraction and classification. Our CAD
system was evaluated on Mini-MIAS database consisting 322
digitalized mammograms. The CAD system-s performance is
evaluated using Receiver Operating Characteristics (ROC) and Freeresponse
ROC (FROC) curves. The archived results are 3.47 false
positives per image (FPpI) and sensitivity of 85%.
Abstract: The purpose of this research is the analysis of the
impact of ICT-related training in the adoption of a learning
management systems (LMS) for teaching practicesby faculties in a
higher education institution. Based on comparative analyses the
impact will be obtained by the number of LMS courses created and
managed by participants in ICT for teaching workshops and those
who have not attended to any workshops. Involving near 1320 LMS
courses and 265 faculties, the results evidence that(i) faculties who
have not attend any workshop present a larger distribution of empty
courses and (ii) faculties who have attended three or more workshops
managed a higher distribution of courses with a considerable level of
use intensity, when compared to the others groups. These findings
supportthe idea that faculty training is a crucial factor in the process
of LMS integration in higher education institutions and that faculties
who have been enrolled in three or more workshops develop a higher
level of technical and pedagogical proficiency in LMS.
Abstract: Lake Nasser is one of the largest reservoirs in the
world. Over 120 million metric tons of sediments are deposited in its
dead storage zone every year. The main objective of the present work
was to determine the physical and chemical characteristics of Lake
Nasser sediments. The sample had a relatively low surface area of 2.9
m2/g which increased more than 3-fold upon chemical activation. The
main chemical elements of the raw sediments were C, O and Si with
some traces of Al, Fe and Ca. The organic functional groups for the
tested sample included O-H, C=C, C-H and C-O, with indications of
Si-O and other metal-C and/or metal-O bonds normally associated
with clayey materials. Potentiometric titration of the sample in
different ionic strength backgrounds revealed an alkaline material with
very strong positive surface charge at pH values just a little less than
the pH of zero charge which is ~9. Surface interactions of the
sediments with the background electrolyte were significant. An
advanced surface complexation model was able to capture these
effects, employing a single-site approach to represent protolysis
reactions in aqueous solution, and to determine the significant surface
species in the pH range of environmental interest.
Abstract: Osteoarthritis (OA) is the most prevalent and far common debilitating form of arthritis which can be defined as a degenerative condition affecting synovial joint. Patients suffering from osteoarthritis often complain of dull ache pain on movement.
Physical agents can fight the painful process when correctly indicated and used such as heat or cold therapy Aim. This study was carried out to: Compare the effect of cold, warm and contrast therapy on controlling knee osteoarthritis associated problems. Setting: The study was carried out in orthopedic outpatient clinics of Menoufia University and teaching Hospitals, Egypt. Sample: A convenient sample of 60 adult patients with unilateral knee osteoarthritis. Tools: three tools were utilized to collect the data. Tool I : An interviewing questionnaire. It comprised of three parts covering sociodemographic data, medical data and adverse effects of the treatment protocol. Tool II : Knee Injury and Osteoarthritis Outcome Score (KOOS) It consists of five main parts. Tool II1 : 0-10 Numeric pain rating scale. Results: reveled that the total knee symptoms score was decreased from moderate symptoms pre intervention to mild symptoms after warm and contrast method of therapy, but the contrast therapy had significant effect in reducing the knee symptoms and pain than the other symptoms. Conclusions: all of the three
methods of therapy resulted in improvement in all knee symptoms and pain but the most appropriate protocol of treatment to relive symptoms and pain was contrast therapy.
Abstract: The solitary wave solution of the quadratic nonlinear Schrdinger equation is determined by the iterative method called Petviashvili method. This solution is also used for the initial condition for the time evolution to study the stability analysis. The spectral method is applied for the time evolution.
Abstract: Economic dispatch problem is an optimization problem where objective function is highly non linear, non-convex, non-differentiable and may have multiple local minima. Therefore, classical optimization methods may not converge or get trapped to any local minima. This paper presents a comparative study of four different evolutionary algorithms i.e. genetic algorithm, bacteria foraging optimization, ant colony optimization and particle swarm optimization for solving the economic dispatch problem. All the methods are tested on IEEE 30 bus test system. Simulation results are presented to show the comparative performance of these methods.
Abstract: Optimization plays an important role in most real
world applications that support decision makers to take the right
decision regarding the strategic directions and operations of the
system they manage. Solutions for traffic management and traffic
congestion problems are considered major problems that most
decision making authorities for cities around the world are looking
for. This review paper gives a full description of the traffic problem
as part of the transportation planning process and present a view as a
framework of urban transportation system analysis where the core of
the system is a transportation network equilibrium model that is
based on optimization techniques and that can also be used for
evaluating an alternative solution or a combination of alternative
solutions for the traffic congestion. Different transportation network
equilibrium models are reviewed from the sequential approach to the
multiclass combining trip generation, trip distribution, modal split,
trip assignment and departure time model. A GIS-Based intelligent
decision support system framework for urban transportation system
analysis is suggested for implementation where the selection of
optimized alternative solutions, single or packages, will be based on
an intelligent agent rather than human being which would lead to
reduction in time, cost and the elimination of the difficulty, by
human being, for finding the best solution to the traffic congestion
problem.
Abstract: We show that Chebyshev Polynomials are a practical representation of computable functions on the computable reals. The paper presents error estimates for common operations and demonstrates that Chebyshev Polynomial methods would be more efficient than Taylor Series methods for evaluation of transcendental functions.
Abstract: Three-dimensional reconstruction of small objects has
been one of the most challenging problems over the last decade.
Computer graphics researchers and photography professionals have
been working on improving 3D reconstruction algorithms to fit the
high demands of various real life applications. Medical sciences,
animation industry, virtual reality, pattern recognition, tourism
industry, and reverse engineering are common fields where 3D
reconstruction of objects plays a vital role. Both lack of accuracy and
high computational cost are the major challenges facing successful
3D reconstruction. Fringe projection has emerged as a promising 3D
reconstruction direction that combines low computational cost to both
high precision and high resolution. It employs digital projection,
structured light systems and phase analysis on fringed pictures.
Research studies have shown that the system has acceptable
performance, and moreover it is insensitive to ambient light.
This paper presents an overview of fringe projection approaches. It
also presents an experimental study and implementation of a simple
fringe projection system. We tested our system using two objects
with different materials and levels of details. Experimental results
have shown that, while our system is simple, it produces acceptable
results.
Abstract: Sustainable development is highly dependent on the
implementation of environmental education programs, which has as
its ultimate goal to produce environmentally literate citizens that
undertake environmentally friendly actions. Efforts on environmental
education along past years are now perceived on the increase of
citizens awareness on European countries and, particularly, in
Portugal. However, we still have a lack of information on the
prevalence of specific behaviors that contributes to sustainability,
influenced by a new attitude toward the environment. The
determination of pro-environmental behaviors prevalence in higher
education students is an important approach to understand to which
extend the next leading generation is, in practice, committed with the
goals of sustainable development. Therefore, present study evaluates
the prevalence of a specific set of behaviors (water savings, energy
savings, environmental criteria on shopping, and mobility) on the
University of Madeira students and discusses their commitment with
sustainable development.
Abstract: Face detection and recognition has many applications
in a variety of fields such as security system, videoconferencing and
identification. Face classification is currently implemented in
software. A hardware implementation allows real-time processing,
but has higher cost and time to-market.
The objective of this work is to implement a classifier based on
neural networks MLP (Multi-layer Perceptron) for face detection.
The MLP is used to classify face and non-face patterns. The systm is
described using C language on a P4 (2.4 Ghz) to extract weight
values. Then a Hardware implementation is achieved using VHDL
based Methodology. We target Xilinx FPGA as the implementation
support.
Abstract: Biological, psychological and social experiences and
perceptions of healthcare services in patients medically diagnosed of
coronary heart disease were investigated using a sample of 10
participants whose responses to the in-depth interview questions
were analyzed based on inter-and-intra-case analyses. The results
obtained revealed that advancing age, single status, divorce and/or
death of spouse and the issue of single parenting negatively impacted
patients- biopsychosocial experiences. The patients- experiences of
physical signs and symptoms, anxiety and depression, past serious
medical conditions, use of self-prescribed medications, family
history of poor mental/medical or physical health, nutritional
problems and insufficient physical activities heightened their risk of
coronary attack. Collectivist culture served as a big source of relieve
to the patients. Patients- temperament, experience of different
chronic life stresses/challenges, mood alteration, regular drinking,
smoking/gambling, and family/social impairments compounded their
health situation. Patients were satisfied with the biomedical services
rendered by the healthcare personnel, whereas their psychological
and social needs were not attended to. Effective procedural treatment
model, a holistic and multidimensional approach to the treatment of
heart disease patients was proposed.
Abstract: The objective of this study was to develop and compare alternative prediction equations of lean meat proportion (LMP) of lamb carcasses. Forty (40) male lambs, 22 of Churra Galega Bragançana Portuguese local breed and 18 of Suffolk breed were used. Lambs were slaughtered, and carcasses weighed approximately 30 min later in order to obtain hot carcass weight (HCW). After cooling at 4º C for 24-h a set of seventeen carcass measurements was recorded. The left side of carcasses was dissected into muscle, subcutaneous fat, inter-muscular fat, bone, and remainder (major blood vessels, ligaments, tendons, and thick connective tissue sheets associated with muscles), and the LMP was evaluated as the dissected muscle percentage. Prediction equations of LMP were developed, and fitting quality was evaluated through the coefficient of determination of estimation (R2 e) and standard error of estimate (SEE). Models validation was performed by k-fold crossvalidation and the coefficient of determination of prediction (R2 p) and standard error of prediction (SEP) were computed. The BT2 measurement was the best single predictor and accounted for 37.8% of the LMP variation with a SEP of 2.30%. The prediction of LMP of lamb carcasses can be based simple models, using as predictors the HCW and one fat thickness measurement.
Abstract: Real-time object tracking is a problem which involves extraction of critical information from complex and uncertain imagedata. In this paper, we present a comprehensive methodology to design an artificial neural network (ANN) for a real-time object tracking application. The object, which is tracked for the purpose of demonstration, is a specific airplane. However, the proposed ANN can be trained to track any other object of interest. The ANN has been simulated and tested on the training and testing datasets, as well as on a real-time streaming video. The tracking error is analyzed with post-regression analysis tool, which finds the correlation among the calculated coordinates and the correct coordinates of the object in the image. The encouraging results from the computer simulation and analysis show that the proposed ANN architecture is a good candidate solution to a real-time object tracking problem.