Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: EcoDam is an adenine-N6 DNA methyltransferase
that methylates the GATC sites in the Escherichia coli genome.
DNA-adenine methylation is not present in higher eukaryotes
including humans. These observations raise the possibility that dam
inhibitors may be used as anti-microbial agents. Polyphosphate
(Poly(P)) is an important metabolite and signaling molecule in
prokaryotes and eukaryotes. Here, by using gel retardation
experiments to investigate the competition of DNA binding by
EcoDam in the presence of polyphosphate, we found that Poly (P)
strongly interferes with DNA binding by EcoDam, while same
concentration of monophosphate does not. In addition, we
demonstrated that Poly (P) binding inhibits the activity of EcoDam
and our results suggest that Poly (P) led to strong inhibition of the
EcoDam catalytic activity, while monophosphate had only moderate
effect.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: The overriding goal of software engineering is to
provide a high quality system, application or a product. To achieve
this goal, software engineers must apply effective methods coupled
with modern tools within the context of a mature software process
[2]. In addition, it is also must to assure that high quality is realized.
Although many quality measures can be collected at the project
levels, the important measures are errors and defects. Deriving a
quality measure for reusable components has proven to be
challenging task now a days. The results obtained from the study are
based on the empirical evidence of reuse practices, as emerged from
the analysis of industrial projects. Both large and small companies,
working in a variety of business domains, and using object-oriented
and procedural development approaches contributed towards this
study. This paper proposes a quality metric that provides benefit at
both project and process level, namely defect removal efficiency
(DRE).
Abstract: In order to survive in a rapidly changing business environment, Malaysian business firms must improve their own business practices and procedures. This paper describes the impact of Critical Success Factors (CSFs) during the Enterprise Resource Planning (ERP) system implementations using the responses from 151 organizations that completed or are in the process of completing an ERP implementation and identifying the key benefits of ERP implementation in the firm. The importance of these factors was investigated within Malaysian companies using questionnaire survey method. Our results provide advice to management on how best to utilize their limited resources to choose those CSFs that are most likely to have an impact upon the implementation of the ERP system.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: Conventional industrial monitoring systems are
tedious, inefficient and the at times integrity of the data is
unreliable. The objective of this system is to monitor industrial
processes specifically the fluid level which will measure the
instantaneous fluid level parameter and respond by text
messaging the exact value of the parameter to the user when
being enquired by a privileged access user. The development of
the embedded program code and the circuit for fluid level
measuring are discussed as well. Suggestions for future
implementations and efficient remote monitoring works are
included.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: Our results showed that treatment with both
cyclooxygenase (COX1 or COX2) inhibitors impair reproduction
parameters of the medaka. Resveratrol (COX1 inhibitor) caused an
decrease in the number of spawning females at the first week of
feeding fish with experimental diets. In the group treated with NS-
398 (COX2 inhibitor) we found the lowest sperm velocity parameters
and decreased linearity of movement. The ovaries of the medaka fed
feed supplemented with Resveratrol or NS-398 were confirmed to
have a lower share of matured oocytes however during the
experiment (four weeks) the number of eggs spawned by females was
similar. Both inhibitors in fish diet (20 mg/kg body weight/day)
caused a decrease in the embryo survival. Our results revealed that
for the medaka female reproduction, activity of both COX enzymes
might be necessary whereas males reproduction competence, as
expressed by sperm motility parameters, might be related to COX2
activity.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: The main objective of this study was to demonstrate that differentiation of infected and vaccinated animals (DIVA) strategy using different ELISA tests is possible when a subunit vaccine (Haemagglutinin protein) is used to prevent Avian influenza. Special emphasis was placed on the differentiation in the serological response to different components of the AIV (Nucleoprotein, Neuraminidase, Haemagglutinin, Nucleocapsid) between chickens that were vaccinated with a whole virus kill vaccine and recombinant vaccine. Furthermore, the potential use of this DIVA strategy using ELISA assays to detect Neuraminidase 1 (N1) was analyzed as strategy in countries where the field virus is H5N1 and the vaccine used is formulated with H5N2. Detection of AIV-s antibodies to any component in serum was negative for all animals on the study days 0-13. At study day 14 the titers of antibodies against Nucleoprotein (NP) and Nucleocapsid (NC) rose in the experimental groups vaccinated with Volvac® AI KV and were negatives during all the trial in the experimental groups vaccinated with a subunit H5; significant statistically differences were observed between these groups (p < 0.05). The seroconversion either Haemagglutinin or Neuraminidase was evident after 21 days post-vaccination in the experimental groups vaccinated with the respective viral fraction. Regarding the main aim of this study and according with the results that were obtained, use a combination of different ELISA test as a DIVA strategy is feasible when the vaccination is carry out with a subunit H5 vaccine. Also is possible to use the ELISA kit to detect Neuraminidase (either N1 or N2) as a DIVA concept in countries where H5N1 is present and the vaccination programs are done with H5N2 vaccine.
Abstract: Any decision-making is based on certain theory. Taking
the public rental housing in Chongqing municipality as an example,
this essay states that the stakeholder theory can provide innovative
criteria and evaluation methods for Public Private Partnership (PPP)
projects. It gives an analysis of how to choose decision-making criteria
for different stakeholders in the PPP model and what measures to take
to meet the criteria to form “symbiotic" decision-making mode
through contracts and to boost the application of PPP model in
large-scale public programs in China.
Abstract: An experimental investigation was performed on pulp
liquid flow in straight ducts with a square cross section. Fully
developed steady flow was visualized and the fiber concentration was
obtained using a light-section method developed by the author et al.
The obtained results reveal quantitatively, in a definite form, the
distribution of the fiber concentration. From the results and
measurements of pressure loss, it is found that the flow characteristics
of pulp liquid in ducts can be classified into five patterns. The
relationships among the distributions of mean and fluctuation of fiber
concentration, the pressure loss and the flow velocity are discussed,
and then the features for each pattern are extracted. The degree of
nonuniformity of the fiber concentration, which is indicated by the
standard deviation of its distribution, is decreased from 0.3 to 0.05
with an increase in the velocity of the tested pulp liquid from 0.4 to
0.8%.
Abstract: The following paper shows an interactive tool which
main purpose is to teach how to play a flute. It consists of three
stages the first one is the instruction and teaching process through a
software application, the second is the practice part when the user
starts to play the flute (hardware specially designed for this
application) this flute is capable of capturing how is being played the
flute and the final stage is the one in which the data captured are sent
to the software and the user is evaluated in order to give him / she a
correction or an acceptance
Abstract: This paper proposes a solution to the motion planning
and control problem of car-like mobile robots which is required to
move safely to a designated target in a priori known workspace
cluttered with swarm of boids exhibiting collective emergent
behaviors. A generalized algorithm for target convergence and
swarm avoidance is proposed that will work for any number of
swarms. The control laws proposed in this paper also ensures
practical stability of the system. The effectiveness of the proposed
control laws are demonstrated via computer simulations of an
emergent behavior.
Abstract: The objective of the paper is twofold. First, to develop a
formal framework for planning for mobile agents. A logical language
based on a temporal logic is proposed that can express a type of
tasks which often arise in network management. Second, to design a
planning algorithm for such tasks. The aim of this paper is to study
the importance of finding plans for mobile agents. Although there
has been a lot of research in mobile agents, not much work has been
done to incorporate planning ideas for such agents. This paper makes
an attempt in this direction. A theoretical study of finding plans for
mobile agents is undertaken. A planning algorithm (based on the
paradigm of mobile computing) is proposed and its space, time, and
communication complexity is analyzed. The algorithm is illustrated
by working out an example in detail.
Abstract: This work is focused on the numerical prediction of the fracture resistance of a flat stiffened panel made of the aluminium alloy 2024 T3 under a monotonic traction condition. The performed numerical simulations have been based on the micromechanical Gurson-Tvergaard (GT) model for ductile damage. The applicability of the GT model to this kind of structural problems has been studied and assessed by comparing numerical results, obtained by using the WARP 3D finite element code, with experimental data available in literature. In the sequel a home-made procedure is presented, which aims to increase the residual strength of a cracked stiffened aluminum panel and which is based on the stochastic design improvement (SDI) technique; a whole application example is then given to illustrate the said technique.
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.
Abstract: In this paper, we consider the problem of tracking
multiple maneuvering targets using switching multiple target motion
models. With this paper, we aim to contribute in solving the problem
of model-based body motion estimation by using data coming from
visual sensors. The Interacting Multiple Model (IMM) algorithm is
specially designed to track accurately targets whose state and/or
measurement (assumed to be linear) models changes during motion
transition. However, when these models are nonlinear, the IMM
algorithm must be modified in order to guarantee an accurate track.
In this paper we propose to avoid the Extended Kalman filter because
of its limitations and substitute it with the Unscented Kalman filter
which seems to be more efficient especially according to the
simulation results obtained with the nonlinear IMM algorithm (IMMUKF).
To resolve the problem of data association, the JPDA
approach is combined with the IMM-UKF algorithm, the derived
algorithm is noted JPDA-IMM-UKF.
Abstract: In this paper, we have applied the homotopy perturbation
method (HPM) for obtaining the analytical solution of unsteady
flow of gas through a porous medium and we have also compared the
findings of this research with some other analytical results. Results
showed a very good agreement between results of HPM and the
numerical solutions of the problem rather than other analytical solutions
which have previously been applied. The results of homotopy
perturbation method are of high accuracy and the method is very
effective and succinct.