Abstract: Variations in the growth rate constant of the Listeria
monocytogenes bacterial species were determined at 37°C in
irradiated environments and compared to the situation of a nonirradiated
environment. The bacteria cells, contained in a suspension
made of a nutrient solution of Brain Heart Infusion, were made to
grow at different frequency (2.30e2.60 GHz) and power (0e400
mW) values, in a plug flow reactor positioned in the irradiated
environment. Then the reacting suspension was made to pass into a
cylindrical cuvette where its optical density was read every 2.5
minutes at a wavelength of 600 nm. The obtained experimental data
of optical density vs. time allowed the bacterial growth rate constant
to be derived; this was found to be slightly influenced by microwave
power, but not by microwave frequency; in particular, a minimum
value was found for powers in the 50e150 mW field.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.
Abstract: A cell-centered finite volume scheme for discretizing diffusion operators on distorted quadrilateral meshes has recently been designed and added to APMFCG to enable that code to be used as a tool for studying explosive magnetic flux compression generators. This paper describes this scheme. Comparisons with analytic results for 2-D test cases are presented, as well as 2-D results from a test of a "realistic" generator configuration.
Abstract: POS (also been called DGPS/IMU) technique can obtain the Exterior Orientation Elements of aerial photo, so the triangulation and DLG production using POS can save large numbers of ground control points (GCP), and this will improve the produce efficiency of DLG and reduce the cost of collecting GCP. This paper mainly research on POS technique in production of 1:10 000 scale DLG on GCP distribution. We designed 23 kinds of ground control points distribution schemes, using integrated sensor direction method to do the triangulation experiments, based on the results of triangulation, we produce a map with the scale of 1:10 000 and test its accuracy. This paper put forward appropriate GCP distributing schemes by experiments and research above, and made preparations for the application of POS technique on photogrammetry 4D data production.
Abstract: A number of studies highlighted problems related to
ERP systems, yet, most of these studies focus on the problems during
the project and implementation stages but not during the postimplementation
use process. Problems encountered in the process of
using ERP would hinder the effective exploitation and the extended
and continued use of ERP systems and their value to organisations.
This paper investigates the different types of problems users
(operational, supervisory and managerial) faced in using ERP and
how 'feral system' is used as the coping mechanism. The paper
adopts a qualitative method and uses data collected from two cases
and 26 interviews, to inductively develop a casual network model of
ERP usage problem and its coping mechanism. This model classified
post ERP usage problems as data quality, system quality, interface
and infrastructure. The model is also categorised the different coping
mechanism through use of 'feral system' inclusive of feral
information system, feral data and feral use of technology.
Abstract: This research examines possible effects of climatic
change focusing on global warming and its impacts on world
agricultural product markets, by using a world food model developed
to consider climate changes. GDP and population for each scenario
were constructed by IPCC and climate data for each scenario was
reported by the Hadley Center and are used in this research to consider
results in different contexts. Production and consumption of primary
agriculture crops of the world for each socio-economic scenario are
obtained and investigated by using the modified world food model.
Simulation results show that crop production in some countries or
regions will have different trends depending on the context. These
alternative contexts depend on the rate of GDP growth, population,
temperature, and rainfall. Results suggest that the development of
environment friendly technologies lead to more consumption of food
in many developing countries. Relationships among environmental
policy, clean energy development, and poverty elimination warrant
further investigation.
Abstract: A systematic and exhaustive method based on the group
structure of a unitary Lie algebra is proposed to generate an enormous
number of quantum codes. With respect to the algebraic structure,
the orthogonality condition, which is the central rule of generating
quantum codes, is proved to be fully equivalent to the distinguishability
of the elements in this structure. In addition, four types of
quantum codes are classified according to the relation of the codeword
operators and some initial quantum state. By linking the unitary Lie
algebra with the additive group, the classical correspondences of some
of these quantum codes can be rendered.
Abstract: Aspect Oriented Programming promises many
advantages at programming level by incorporating the cross cutting
concerns into separate units, called aspects. Join Points are
distinguishing features of Aspect Oriented Programming as they
define the points where core requirements and crosscutting concerns
are (inter)connected. Currently, there is a problem of multiple
aspects- composition at the same join point, which introduces the
issues like ordering and controlling of these superimposed aspects.
Dynamic strategies are required to handle these issues as early as
possible. State chart is an effective modeling tool to capture dynamic
behavior at high level design. This paper provides methodology to
formulate the strategies for multiple aspect composition at high level,
which helps to better implement these strategies at coding level. It
also highlights the need of designing shared join point at high level,
by providing the solutions of these issues using state chart diagrams
in UML 2.0. High level design representation of shared join points
also helps to implement the designed strategy in systematic way.
Abstract: Polylactic acid-g-polyvinyl acetate (PLLA-g-PVAc)
was used as a compatibilizer for 50/50 starch/PLLA blend. PLLA-g-
PVAc with different mol% of PVAc contents were prepared by
grafting PVAc onto PLLA backbone via free radical polymerization
in solution process. Various conditions such as type and the amount
of initiator, monomer concentration, polymerization time and
temperature were studied. Results showed that the highest mol% of
PVAc grafting (16 mol%) was achieved by conducting graft
copolymerization in toluene at 110°C for 10 h using DCP as an
initiator. Chemical structure of the PVAc grafted PLLA was
confirmed by 1H NMR. Blending of modified starch and PLLA in the
presence compatibilizer with different amounts and mol% PVAc was
acquired using internal mixer at 160°C for 15 min. Effects of PVAc
content and the amount of compatibilizer on mechanical properties of
polymer blend were studied. Results revealed that tensile strength and
tensile modulus of polymer blend with higher PVAc grafting content
compatibilizer showed better properties than that of lower PVAc
grafting content compatibilizer. The amount of compatibilizer was
found optimized in the range of 0.5-1.0 Wt% depending on the mol%
PVAc.
Abstract: Polarization modulation infrared reflection absorption
spectroscopy (PM-IRRAS) in combination with electrochemistry,
was employed to study the influence of surface charge (potential) on
the kinetics of bovine serum albumin (BSA) adsorption on a
biomedical-grade 316LVM stainless steel surface is discussed. The
BSA adsorption kinetics was found to greatly depend on the surface
potential. With an increase in surface potential towards more
negative values, both the BSA initial adsorption rate and the
equilibrium (saturated) surface concentration also increased. Both
effects were explained on the basis of replacement of well-ordered
water molecules at the 316LVM / solution interface, i.e. by the
increase in entropy of the system.
Abstract: This paper proposes, implements and evaluates an original discretization method for continuous random variables, in order to estimate the reliability of systems for which stress and strength are defined as complex functions, and whose reliability is not derivable through analytic techniques. This method is compared to other two discretizing approaches appeared in literature, also through a comparative study involving four engineering applications. The results show that the proposal is very efficient in terms of closeness of the estimates to the true (simulated) reliability. In the study we analyzed both a normal and a non-normal distribution for the random variables: this method is theoretically suitable for each parametric family.
Abstract: Visible Light Communication (VLC) offers advantages of low energy consumption, licence free and RF interference free operation. One application area for VLC is in the provision of health centred services circumventing issues of interference with any biomedical device within the environment. VLC performamce is affected by natural light restricting systems avilability and relibility. The paper presents an analysis of the performance of VLC systems under different meteorological conditions. The evaluation considered the impact of natural light as a function of different reflection surfaces in different room sizes.
Abstract: The major objective of this study is to understand the
potential of a newly fabricated equipment to study the thermal
properties of nonwoven textile fabrics treated with aerogel at subzero
temperatures. Thermal conductivity was calculated by using the
empirical relation Fourier’s law, The relationship between the
thermal conductivity and thermal resistance of the samples were
studied at various environmental temperatures (which was set in the
clima temperature system between +25oC to -25oC). The newly
fabricated equipment was found to be a suitable for measuring at
subzero temperatures. This field of measurements is being developed
and will be the subject of further research which will be more suitable
for measurement of the various thermal characteristics.
Abstract: In the competitive environment of aircraft industries it becomes absolutely necessary to improve the efficiency, performance of the aircrafts to reduce the development and operating costs considerably, in order to capitalize the market. An important contribution to improve the efficiency and performance can be
achieved by decreasing the aircraft weight through considerable
usage of composite materials in primary aircraft structures. In this study, a type of composite material called Carbon Fiber Reinforced
Plastic (CFRP) is explored for the usage is aircraft skin panels. Even
though there were plenty of studies and research has been already
carried out, here a practical example of an aircraft skin panel is taken
and substantiated the benefits of composites material usage over the
metallic skin panel. A crown skin panel of a commercial aircraft is
designed using both metal and composite materials. Stress analysis
has been carried out for both and margin of safety is estimated for the
critical load cases. The skin panels are compared for manufacturing,
tooling, assembly and cost parameters. Detail step by step comparison between metal and composite constructions are studied
and results are tabulated for better understanding.
Abstract: This paper proposes a new approach to perform the
problem of real-time face detection. The proposed method combines
primitive Haar-Like feature and variance value to construct a new
feature, so-called Variance based Haar-Like feature. Face in image
can be represented with a small quantity of features using this
new feature. We used SVM instead of AdaBoost for training and
classification. We made a database containing 5,000 face samples
and 10,000 non-face samples extracted from real images for learning
purposed. The 5,000 face samples contain many images which have
many differences of light conditions. And experiments showed that
face detection system using Variance based Haar-Like feature and
SVM can be much more efficient than face detection system using
primitive Haar-Like feature and AdaBoost. We tested our method on
two Face databases and one Non-Face database. We have obtained
96.17% of correct detection rate on YaleB face database, which is
higher 4.21% than that of using primitive Haar-Like feature and
AdaBoost.
Abstract: In this paper, a new hybrid of genetic algorithm (GA)
and simulated annealing (SA), referred to as GSA, is presented. In
this algorithm, SA is incorporated into GA to escape from local
optima. The concept of hierarchical parallel GA is employed to
parallelize GSA for the optimization of multimodal functions. In
addition, multi-niche crowding is used to maintain the diversity in
the population of the parallel GSA (PGSA). The performance of the
proposed algorithms is evaluated against a standard set of multimodal
benchmark functions. The multi-niche crowding PGSA and normal
PGSA show some remarkable improvement in comparison with the
conventional parallel genetic algorithm and the breeder genetic
algorithm (BGA).
Abstract: To date, theoretical studies concerning the Carbon
Fiber Reinforced Polymer (CFRP) strengthening of RC beams with
openings have been rather limited. In addition, various numerical
analyses presented so far have effectively simulated the behaviour of
solid beam strengthened by FRP material. In this paper, a two
dimensional nonlinear finite element analysis is presented to validate
against the laboratory test results of six RC beams. All beams had the
same rectangular cross-section geometry and were loaded under four
point bending. The crack pattern results of the finite element model
show good agreement with the crack pattern of the experimental
beams. The load midspan deflection curves of the finite element
models exhibited a stiffer result compared to the experimental beams.
The possible reason may be due to the perfect bond assumption used
between the concrete and steel reinforcement.
Abstract: Since MEMS gyro sensors measure not angle of rotation but angular rate, an estimator is designed to estimate the angles in many applications. Gyro and accelerometer are used to improve estimating accuracy of the angle. This paper presents a method of finding filter coefficients of the well-known estimator which is to get rotation angles from gyro and accelerometer data. In order to verify the performance of our method, the estimated angle is compared with the encoder output in a rotary pendulum system.
Abstract: White scar oyster (Crassostrea belcheri) is often eaten
raw and being the leading vehicle for foodborne disease, especially
Salmonella Weltevreden which exposed the prominent and most
resistant to radiation. Gamma irradiation at a low dose of 1 kGy was
enough to eliminate S. Weltevreden contaminated in oyster meat at a
level up to 5 log CFU/g while it still retain the raw characteristics and
equivalent sensory quality as the non-irradiated one. Process
development of ready-to-eat chilled oyster meat was conducted by
shucking the meat, individually packed in plastic bags, subjected to 1
kGy gamma radiation at chilled condition and then stored in 4oC
refrigerated temperature. Microbiological determination showed the
absence of S. Weltevreden (5 log CFU/g initial inoculated) along the
whole storage time of 30 days. Sensory evaluation indicated the
decreasing in sensory scores along storage time which determining
the product shelf life to be 18 days compared to 15 days of nonirradiated
one. The most advantage of developed process was to
provide the safe raw oyster to consumers and in addition sensory
quality retained and 3-day extension shelf life also exist.
Abstract: The huge development of new technologies and the
apparition of open communication system more and more
sophisticated create a new challenge to protect digital content from
piracy. Digital watermarking is a recent research axis and a new
technique suggested as a solution to these problems. This technique
consists in inserting identification information (watermark) into
digital data (audio, video, image, databases...) in an invisible and
indelible manner and in such a way not to degrade original medium-s
quality. Moreover, we must be able to correctly extract the
watermark despite the deterioration of the watermarked medium (i.e
attacks). In this paper we propose a system for watermarking satellite
images. We chose to embed the watermark into frequency domain,
precisely the discrete wavelet transform (DWT). We applied our
algorithm on satellite images of Tunisian center. The experiments
show satisfying results. In addition, our algorithm showed an
important resistance facing different attacks, notably the compression
(JEPG, JPEG2000), the filtering, the histogram-s manipulation and
geometric distortions such as rotation, cropping, scaling.