Abstract: Fluid viscous damping systems are well suited for
many air vehicles subjected to shock and vibration. These damping
system work with the principle of viscous fluid throttling through the
orifice to create huge pressure difference between compression and
rebound chamber and obtain the required damping force. One
application of such systems is its use in aircraft door system to
counteract the door’s velocity and safely stop it. In exigency
situations like crash or emergency landing where the door doesn’t
open easily, possibly due to unusually tilting of fuselage or some
obstacles or intrusion of debris obstruction to move the parts of the
door, such system can be combined with other systems to provide
needed force to forcefully open the door and also securely stop it
simultaneously within the required time i.e. less than 8 seconds. In
the present study, a hydraulic system called snubber along with other
systems like actuator, gas bottle assembly which together known as
emergency power assist system (EPAS) is designed, built and
experimentally studied to check the magnitude of angular velocity,
damping force and time required to effectively open the door.
Whenever needed, the gas pressure from the bottle is released to
actuate the actuator and at the same time pull the snubber’s piston to
operate the emergency opening of the door. Such EPAS installed in
the suspension arm of the aircraft door is studied explicitly changing
parameters like orifice size, oil level, oil viscosity and bypass valve
gap and its spring of the snubber at varying temperature to generate
the optimum design case. Comparative analysis of the EPAS at
several cases is done and conclusions are made. It is found that
during emergency condition, the system opening time and angular
velocity, when snubber with 0.3mm piston and shaft orifice and
bypass valve gap of 0.5 mm with its original spring is used, shows
significant improvement over the old ones.
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: Sound exposure effects have been investigated by
broadcasting a group of broilers with sound of Quran verses (Group
B) whereas the other group is the control broilers (Group C). The
growth rate comparisons in terms of weight and raw meat texture
measured by shear force have been investigated. Twenty-seven
broilers were randomly selected from each group on Day 24 and
weight measurement was carried out every week till the harvest day
(Day 39).Group B showed a higher mean weight on Day 24 (1.441 ±
0.013 kg) than Group C. Significant difference in the weight on Day
39 existed for Group B compared to Group C (p < 0.05). However,
there was no significant (p >0.05) difference of shear force in the
same muscles (breast and drumstick raw meat) of both groups but the
shear force of the breast meat for Group B and C broilers was lower
(p < 0.05) than that of their drumstick meat. Thus, broadcasting the
sound of Quran verses in the coop can be applied to improve the
growth rate of broilers for producing better quality poultry.
Abstract: In recent years, the hair building fiber has become
popular, in other words, it is an effective method which helps people
who suffer hair loss or sparse hair since the hair building fiber is
capable to create a natural look of simulated hair rapidly. In the
markets, there are a lot of hair fiber brands that have been designed to
formulate an intense bond with hair strands and make the hair appear
more voluminous instantly. However, those products have their own
set of properties. Thus, in this report, some measurement techniques
are proposed to identify those products. Up to five different brands of
hair fiber are tested. The electrostatic and dielectric properties of the
hair fibers are macroscopically tested using design DC and high
frequency microwave techniques. Besides, the hair fibers are
microscopically analysis by magnifying the structures of the fiber
using scanning electron microscope (SEM). From the SEM photos,
the comparison of the uniformly shaped and broken rate of the hair
fibers in the different bulk samples can be observed respectively.
Abstract: Waxapple (Syzygium samarngense Merr.et Perry) is an
important tropical fruit in Taiwan. The famous producing area is
located on the coast in Pingtung County. Land subsidence and climate
change will tend to soil alkalization more seriously. This study was to
evaluate the effects of NaCl in waxapple seedlings. NaCl salinity
reduced waxapple shoot growth; it may due to reducing relative water
content in leaf and new shoot. Leaf Cl and Na concentration were
increased but K, Ca, and Mg content had no significant difference after
irrigated with NaCl for six weeks. In roots, Na and Cl content increase
significantly with 90 mM NaCl treatment, but K, Ca, and Mg content
was reduced. 30-90mM Nacl treatment do not effect K/Na, Ca/Na and
Mg/Na ratio, but decrease significantly in 90mM treatment in roots.
The leaf and root electrolyte leakage were significantly affected by 90
mM NaCl treatment. Suggesting 90mM was optimum concentration
for sieve out other tolerance waxapples verities.
Abstract: This paper discusses the undesirable charge transfer
through the parasitic capacitances of the input transistors in a
multi-inputs voltage sense amplifier. Its intrinsic rail-to-rail voltage
transitions at the output nodes inevitably disturb the input sides
through the capacitive coupling between the outputs and inputs. Then,
it can possible degrade the stabilities of the reference voltage levels.
Moreover, it becomes more serious in multi-channel systems by
altering them for other channels, and so degrades the linearity of the
overall systems. In order to alleviate the internal node voltage
transition, the internal node stabilization techniques are proposed. It
achieves 45% and 40% improvements for node stabilization and input
referred disturbance, respectively.
Abstract: The planning of geological survey works is an
iterative process which involves planner, geologist, civil engineer and
other stakeholders, who perform different roles and have different
points of view. Traditionally, the team used paper maps or CAD
drawings to present the proposal which is not an efficient way to
present and share idea on the site investigation proposal such as
sitting of borehole location or seismic survey lines. This paper
focuses on how a GIS approach can be utilised to develop a webbased
system to support decision making process in the planning of
geological survey works and also to plan site activities carried out by
Singapore Geological Office (SGO). The authors design a framework
of building an interactive web-based GIS system, and develop a
prototype, which enables the users to obtain rapidly existing
geological information and also to plan interactively borehole
locations and seismic survey lines via a web browser. This prototype
system is used daily by SGO and has shown to be effective in
increasing efficiency and productivity as the time taken in the
planning of geological survey works is shortened. The prototype
system has been developed using the ESRI ArcGIS API 3.7 for Flex
which is based on the ArcGIS 10.2.1 platform.
Abstract: The characteristic requirement for producing
rectangular shape bottles was a uniform thickness of the plastic bottle
wall. Die shaping was a good technique which controlled the wall
thickness of bottles. An advance technology which was the finite
element method (FEM) for blowing parison to be a rectangular shape
bottle was conducted to reduce waste plastic from a trial and error
method of a die shaping and parison control method. The artificial
intelligent (AI) comprised of artificial neural network and genetic
algorithm was selected to optimize the die gap shape from the FEM
results. The application of AI technique could optimize the suitable
die gap shape for the parison blow molding which did not depend on
the parison control method to produce rectangular bottles with the
uniform wall. Particularly, this application can be used with cheap
blow molding machines without a parison controller therefore it will
reduce cost of production in the bottle blow molding process.
Abstract: Many aluminum motorcycle parts produced by a high
pressure die casting. Some parts such as fuel caps were a thin and
complex shape. This part risked for porosities and blisters on surface
if it only depended on an experience of mold makers for mold design.
This research attempted to use CAST-DESIGNER software
simulated the high pressure die casting process with the same process
parameters of a motorcycle fuel cap production. The simulated results
were compared with fuel cap products and expressed the same
porosity and blister locations on cap surface. An average of absolute
difference of simulated results was obtained 0.094 mm when
compared the simulated porosity and blister defect sizes on the fuel
cap surfaces with the experimental micro photography. This
comparison confirmed an accuracy of software and will use the
setting parameters to improve fuel cap molds in the further work.
Abstract: Non-linear FEM calculations are indispensable when
important technical information like operating performance of a
rubber component is desired. For example rubber bumpers built into
air-spring structures may undergo large deformations under load,
which in itself shows non-linear behavior. The changing contact
range between the parts and the incompressibility of the rubber
increases this non-linear behavior further. The material
characterization of an elastomeric component is also a demanding
engineering task.
The shape optimization problem of rubber parts led to the study of
FEM based calculation processes. This type of problems was posed
and investigated by several authors. In this paper the time demand of
certain calculation methods are studied and the possibilities of time
reduction is presented.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: This study was developed to compare the behavior
and the ability of polymer foam composites towards sound absorption
test of Shorea leprosula wood (SL) of acid hydrolysis treatment with
particle size
Abstract: The main aim of this research was to investigate a
prototype bamboo shading device. There were two objectives to this
study: first, to investigate the effects of non-chemical treatments on
bamboo shading devices damaged by powder-post beetles and fungi,
and second to develop a prototype bamboo shading device. This
study of the effects of non-chemical treatments on bamboo shading
devices damage by powder-post beetles in the laboratory showed
that, among seven treatments tested, wood vinegar treatment can
protect powder-post beetles better than the original method by up to
92.91%. It was also found that wood vinegar treatment shows the
best performance in fungi protection and works better than the
original method by up to 40%. A second experiment was carried out
by constructing four bamboo shading devices and installing them on
a building for 28 days. All aspects of shading device were
investigated in terms of their beauty, durability, and ease of
construction and assembly. The final prototype was developed from
the lessons learned from the test results. In conclusion, this study
showed the effectiveness of some natural preservatives against insect
and fungi damage, and it also illustrated the characteristics of a
prototype bamboo shading device that can be constructed by rural
workers within one week.
Abstract: The organizations in the knowledge economy era have
recognized the importance of building knowledge assets for
sustainable growth and development. In comparison to other
industries, Information Technology (IT) enterprises, holds an edge in
developing an effective Knowledge Management (KM) programmethanks
to their in-house technological abilities. This paper tries to
study the various knowledge based incentive programmes and its
effect on Knowledge Sharing and Learning in the context of the
Indian IT sector. A conceptual model is developed linking KM
Incentives, Knowledge Sharing and Learning. A questionnaire study
is conducted to collect primary data from the knowledge workers of
the IT organizations located in India. The data was analysed using
Structural Equation Modeling using Partial Least Square method. The
results show a strong influence of knowledge management incentives
on knowledge sharing and an indirect influence on learning.
Abstract: In this paper, an analysis of some model order
reduction techniques is presented. A new hybrid algorithm for model
order reduction of linear time invariant systems is compared with the
conventional techniques namely Balanced Truncation, Hankel Norm
reduction and Dominant Pole Algorithm (DPA). The proposed hybrid
algorithm is known as Clustering Dominant Pole Algorithm (CDPA),
is able to compute the full set of dominant poles and its cluster center
efficiently. The dominant poles of a transfer function are specific
eigenvalues of the state space matrix of the corresponding dynamical
system. The effectiveness of this novel technique is shown through
the simulation results.
Abstract: Agriculture is the backbone of economy of Pakistan
and cotton is the major agricultural export and supreme source of raw
fiber for our textile industry. To combat severe problems of insect
and weed, combination of three genes namely Cry1Ac, Cry2A and
EPSPS genes was transferred in locally cultivated cotton variety
MNH-786 with the use of Agrobacterium mediated genetic
transformation. The present study focused on the molecular screening
of transgenic cotton plants at T3 generation in order to confirm
integration and expression of all three genes (Cry1Ac, Cry2A and
EPSP synthase) into the cotton genome. Initially, glyphosate spray
assay was used for screening of transgenic cotton plants containing
EPSP synthase gene at T3 generation. Transgenic cotton plants which
were healthy and showed no damage on leaves were selected after 07
days of spray. For molecular analysis of transgenic cotton plants in
the laboratory, the genomic DNA of these transgenic cotton plants
were isolated and subjected to amplification of the three genes. Thus,
seventeen out of twenty (Cry1Ac gene), ten out of twenty (Cry2A
gene) and all twenty (EPSP synthase gene) were produced positive
amplification. On the base of PCR amplification, ten transgenic plant
samples were subjected to protein expression analysis through
ELISA. The results showed that eight out of ten plants were actively
expressing the three transgenes. Real-time PCR was also done to
quantify the mRNA expression levels of Cry1Ac and EPSP synthase
gene. Finally, eight plants were confirmed for the presence and active
expression of all three genes at T3 generation.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.