Abstract: The posteroanterior manipulation technique is usually include in the procedure of the lumbar spine to evaluate the intervertebral motion according to mechanical resistance. The mechanical device with visual feedback was proposed that allows one to analysis the lumbar segments mobility “in vivo" facilitating for the therapist to take its treatment evolution. The measuring system uses load cell and displacement sensor to estimate spine stiffness. In this work, the device was tested by 2 therapists, female, applying posteroanterior force techniques to 5 volunteers, female, with frequency of approximately 1.2-1.8 Hz. A test-retest procedure was used for 2 periods of day. The visual feedback results small variation of forces and cycle time during 6 cycles rhythmic application. The stiffness values showed good agreement between test-retest procedures when used same order of maximum forces.
Abstract: This paper presents a CFD analysis of the flow around
a 30° inclined flat plate of infinite span. Numerical predictions have
been compared to experimental measurements, in order to assess the
potential of the finite volume code of determining the aerodynamic
forces acting on a flat plate invested by a fluid stream of infinite
extent.
Several turbulence models and spatial node distributions have
been tested and flow field characteristics in the neighborhood of the
flat plate have been numerically investigated, allowing the
development of a preliminary procedure to be used as guidance in
selecting the appropriate grid configuration and the corresponding
turbulence model for the prediction of the flow field over a twodimensional
inclined plate.
Abstract: The Sensor Network consists of densely deployed
sensor nodes. Energy optimization is one of the most important
aspects of sensor application design. Data acquisition and aggregation
techniques for processing data in-network should be energy efficient.
Due to the cross-layer design, resource-limited and noisy nature
of Wireless Sensor Networks(WSNs), it is challenging to study
the performance of these systems in a realistic setting. In this
paper, we propose optimizing queries by aggregation of data and
data redundancy to reduce energy consumption without requiring
all sensed data and directed diffusion communication paradigm to
achieve power savings, robust communication and processing data
in-network. To estimate the per-node power consumption POWERTossim
mica2 energy model is used, which provides scalable and
accurate results. The performance analysis shows that the proposed
methods overcomes the existing methods in the aspects of energy
consumption in wireless sensor networks.
Abstract: A novel methodology has been used to design an
evaporator coil of a refrigerant. The methodology used is through a
complete Computer Aided Design /Computer Aided Engineering
approach, by means of a Computational Fluid Dynamic/Finite
Element Analysis model which is executed many times for the
thermal-fluid exploration of several designs' configuration by an
commercial optimizer. Hence the design is carried out automatically
by parallel computations, with an optimization package taking the
decisions rather than the design engineer. The engineer instead takes
decision regarding the physical settings and initializing of the
computational models to employ, the number and the extension of the
geometrical parameters of the coil fins and the optimization tools to
be employed. The final design of the coil geometry found to be better
than the initial design.
Abstract: Resistive switching of aluminum nitride (AlNx) thin film was demonstrated in a TaN/AlNx/TiN memory cell that was prepared by sputter deposition techniques. The memory cell showed bipolar switching of resistance between +3.5 V and –3.5 V. The resistance ratio of high resistance state (HRS) to low resistance state (HRS), RHRS/RLRS, was about 2 over 100 cycles of endurance test. Both the LRS and HRS of the memory cell exhibited ohmic conduction at low voltages and Poole-Frenkel emission at high voltages. The electrical conduction in the TaN/AlNx/TiN memory cell was possibly attributed to the interactions between charges and defects in the AlNx film.
Abstract: This paper provides some thoughts about the lack of
attentiveness of building commissioning in the construction industry
and the lack of handling in project commissioning as an integral part
of the project life-cycle. Many have perceived commissioning as the
problem solving process of a project, rather than the start up of the
equipment, or the handing over of the project to the client. Therefore,
there is a lack of proper attention in the planning of commissioning
as a vital part of the project life-cycle. This review paper aims to
highlight the benefits of building commissioning and to propose the
lacking of knowledge gap on building commissioning. Finally, this
paper hopes to propose the shift of focus on this matter in future
research.
Abstract: The term interactive education indicates the meaning
related with multidisciplinary aspects of distance education following
contemporary means around a common basis with different
functional requirements. The aim of this paper is to reflect the new
techniques in education with the new methods and inventions. These
methods are better supplied by interactivity. The integration of
interactive facilities in the discipline of education with distance
learning is not a new concept but in addition the usage of these
methods on design issue is newly being adapted to design education.
In this paper the general approach of this method and after the
analysis of different samples, the advantages and disadvantages of
these approaches are being identified. The method of this paper is to
evaluate the related samples and then analyzing the main hypothesis.
The main focus is to mention the formation processes of this
education. Technological developments in education should be
filtered around the necessities of the design education and the
structure of the system could then be formed or renewed. The
conclusion indicates that interactive methods of education in design
issue is a meaning capturing not only technical and computational
intelligence aspects but also aesthetical and artistic approaches
coming together around the same purpose.
Abstract: BioEnergy is an archetypal appropriate technology
and alternate source of energy in rural areas of China, and can meet
the basic need for cooking fuel in rural areas. The paper introduces
with an alternate mean of research that can accelerate the biogas
energy production. Tithonia diversifolia or the Tree marigold can be
hailed as mesophillic anaerobic digestion to increase the production
of more Bioenergy. Tithonia diversifolia is very native to Mexico and
Central America, which can be served as ornamental plants- green
manure and can prevent soil erosion. Tithonia diversifolia is widely
grown and known to Asia, Africa, America and Australia as well.
Nowadays, Considering China’s geographical condition it is found
that Tithonia diversifolia is widely growing plant in the many tropical
and subtropical regions of southern Yunnan- which can have great
usage in accelerating and increasing the Bioenergy production
technology. The paper discussed aiming at proving possibility that
Tithonia diversifolia can be applied in biogas fermentation and its
biogas production potential, the research carried experiment on
Tithonia diversifolia biogas fermentation under the mesophilic
condition (35 Celsius Degree). The result revealed that Tithonia
diversifolia can be used as biogas fermentative material, and 6%
concentration can get the best biogas production, with the TS biogas
production rate 656mL/g and VS biogas production rate 801mL/g. It
is well addressed that Tithonia diversifolia grows wildly in 53
Counties and 9 cities of Yunnan Province, which mainly grows in
form of the road side plants, the edge of the field, countryside, forest
edge, open space; of which demersum-natures can form dense
monospecific beds -causing serious harm to agricultural production
landforms threatening the ecological system as a potentially harmful
exotic plant. There are also found the three types of invasive daisy
alien plants -Eupatorium adenophorum, Eupatorium Odorata and
Tithonia diversifolia in Yunnan Province of China-among them the
Tithonia diversifolia is responsible for causing serious harm to
agricultural production. In this paper we have designed the
experimental explanation of Biogas energy production that requires
anaerobic environment and some microbes; Tithonia diversifolia
plant has been taken into consideration while carrying experiments
and with successful resulting of generating more BioEnergy
emphasizing on the practical applications of Tithonia diversifolia.
This paper aims at- to find a new mechanism to provide a more
scientific basis for the development of this plant herbicides in Biogas
energy and to improve the utilization throughout the world as well.
Abstract: A generalised relational data model is formalised for
the representation of data with nested structure of arbitrary depth. A
recursive algebra for the proposed model is presented. All the
operations are formally defined. The proposed model is proved to be
a superset of the conventional relational model (CRM). The
functionality and validity of the model is shown by a prototype
implementation that has been undertaken in the functional
programming language Miranda.
Abstract: The need for micromechanical inertial sensors is increasing
in future electronic stability control (ESC) and other positioning,
navigation and guidance systems. Due to the rising density of
sensors in automotive and consumer devices the goal is not only to get
high performance, robustness and smaller package sizes, but also to
optimize the energy management of the overall sensor system. This
paper presents an evaluation concept for a surface micromachined
yaw rate sensor. Within this evaluation concept an energy-efficient
operation of the drive mode of the yaw rate sensor is enabled. The
presented system concept can be realized within a power management
subsystem.
Abstract: Researchers investigate arious strategies to develop composite beams and maximize the structural advantages. This study
attempted to conduct experiments and analysis of changes in the
neutral axis of positive moments of a Green Beam. Strain
compatibility analysis was used, and its efficiency was demonstrated
by comparing experimental and analytical values. In the comparison of
neutral axis, the difference between experimental and analytical values
was found to range from 8.8~26.2%. It was determined that strain
compatibility analysis can be useful for predicting the behaviors of
composite beams, with the ability to predict the behavior of not only
the elastic location of the composite member, but also of the plastic
location
Abstract: There are many virtual payment systems available to
conduct micropayments. It is essential that the protocols satisfy the
highest standards of correctness. This paper examines the Netpay
Protocol [3], provide its formalization as automata model, and prove
two important correctness properties, namely absence of deadlock
and validity of an ecoin during the execution of the protocol. This
paper assumes a cooperative customer and will prove that the
protocol is executing according to its description.
Abstract: The liquid cargo contained in a partly-filled road tank
vehicle is prone to dynamic slosh movement when subjected to
external disturbances. The slosh behavior has been identified as a
significant factor impairing the safety of liquid cargo transportation.
The laboratory experiments have been conducted for analyzing fluid
slosh in partly filled tanks. The experiment results measured under
forced harmonic excitations reveal the three-dimensional nature of
the fluid motion and coupling between the lateral and longitudinal
fluid slosh at resonance. Several spectral components are observed
for the transient slosh forces, which can be associated with the
excitation, resonance, and beat frequencies. The peak slosh forces
and moments in the vicinity of resonance are significantly larger than
those of the equivalent rigid mass. Due to the nature of coupling
between sloshing fluid and vehicle body, the issue of the dynamic
fluid-structure interaction is essential in the analysis of tank-vehicle
dynamics. A dynamic pitch plane model of a Tridem truck
incorporated the fluid slosh dynamics is developed to analyze the
fluid-vehicle interaction under the straight-line braking maneuvers.
The results show that the vehicle responses are highly associated
with the characteristics of fluid slosh force and moment.
Abstract: The hybrid membranes containing inorganic materials in polymer matrix are identified as a remarkable family of proton conducting hybrid electrolytes. In this work, the proton conducting inorganic/organic hybrid membranes for proton exchange membrane fuel cells (PEMFCs) were prepared using polyvinyl alcohol (PVA), tetraethoxyorthosilane (TEOS) and heteropolyacid (HPA). The synthesized hybrid membranes were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction spectroscopy (XRD), Scanning electron microscopy (SEM) and Thermogravimetry analysis (TGA). The effects of heteropolyacid incorporation on membrane properties, including morphology and thermal stability were extensively investigated.
Abstract: Global competition is tightening and companies have
to think how to remain competitive. The main aim of this paper is to
discuss how Finnish foundries will remain competitive. To fulfil the
aim, we conducted interviews in nine companies using castings and
analysed buyer–supplier relationships, current competitive
advantages of Finnish foundries and customer perspectives on how
Finnish foundries remain competitive. We found that the customerfoundry
relationship is still closer to traditional subcontracting than
partnering and general image of foundries is negative. Current
competitive advantages of Finnish foundries include designing
cooperation, proximity and flexibility. Casting users state that
Finnish foundries should sell their know-how and services instead of
their capacity, concentrate on prototype, single and short series
castings and supply ready-to-install cast components directly to
customers- assembly lines.
Abstract: The development of aid's systems for the medical
diagnosis is not easy thing because of presence of inhomogeneities in
the MRI, the variability of the data from a sequence to the other as
well as of other different source distortions that accentuate this
difficulty. A new automatic, contextual, adaptive and robust
segmentation procedure by MRI brain tissue classification is
described in this article. A first phase consists in estimating the
density of probability of the data by the Parzen-Rozenblatt method.
The classification procedure is completely automatic and doesn't
make any assumptions nor on the clusters number nor on the
prototypes of these clusters since these last are detected in an
automatic manner by an operator of mathematical morphology called
skeleton by influence zones detection (SKIZ). The problem of
initialization of the prototypes as well as their number is transformed
in an optimization problem; in more the procedure is adaptive since it
takes in consideration the contextual information presents in every
voxel by an adaptive and robust non parametric model by the
Markov fields (MF). The number of bad classifications is reduced by
the use of the criteria of MPM minimization (Maximum Posterior
Marginal).
Abstract: The presented paper shows the possibility of using
holographic interferometry for measurement of temperature field in
moving fluids. There are a few methods for identification of velocity
fields in fluids, such us LDA, PIV, hot wire anemometry. It is very
difficult to measure the temperature field in moving fluids. One of the
often used methods is Constant Current Anemometry (CCA), which
is a point temperature measurement method. Data are possibly
acquired at frequencies up to 1000Hz. This frequency should be
limiting factor for using of CCA in fluid when fast change of
temperature occurs. This shortcoming of CCA measurements should
be overcome by using of optical methods such as holographic
interferometry. It is necessary to employ a special holographic setup
with double sensitivity instead of the commonly used Mach-Zehnder
type of holographic interferometer in order to attain the parameters
sufficient for the studied case. This setup is not light efficient like the
Mach-Zehnder type but has double sensitivity. The special technique
of acquiring and phase averaging of results from holographic
interferometry is also presented. The results from the holographic
interferometry experiments will be compared with the temperature
field achieved by methods CCA method.
Abstract: Double heterogeneity of randomly located pebbles in
the core and Coated Fuel Particles (CFPs) in the pebbles are specific
features in pebble bed reactors and usually, because of difficulty to
model with MCNP code capabilities, are neglected. In this study,
characteristics of HTR-10, Tsinghua University research reactor, are
used and not only double heterogeneous but also truncated CFPs and
Pebbles are considered.Firstly, 8335 CFPs are distributed randomly
in a pebble and then the core of reactor is filled with those pebbles
and graphite pebbles as moderator such that 57:43 ratio of fuel and
moderator pebbles is established.Finally, four different core
configurations are modeled. They are Simple Cubic (SC) structure
with truncated pebbles,SC structure without truncated pebble, and
Simple Hexagonal(SH) structure without truncated pebbles and SH
structure with truncated pebbles. Results like effective multiplication
factor (Keff), critical height,etc. are compared with available data.
Abstract: Absorption and fluorescence spectra of quinine
sulphate (QSD) have been recorded at room temperature in wide
range of solvents of different polarities. The ground-state dipole
moment of QSD was obtained from quantum mechanical calculations
and the excited state dipole moment of QSD was estimated from
Bakhshiev-s and Kawski-Chamma-Viallet-s equations by means of
solvatochromic shift method. Higher value of dipole moment is
observed for excited state as compared to the corresponding ground
state value and this is attributed to the more polar excited state of
QSD.
Abstract: The objective of this study was to develop safety practices which is suitable for Thai industrial operators from Incident and Injury Free, IIF to create safety behavior and reduce the un-safe records in the petroleum industry. A number of 310 technicians i.e., 295 males and 15 females, in service maintenance section participated in this program. The safety attitude level and safety behavior level for pre-attended and post-attended the developed safety practices of the technicians were evaluated using questionnaire procedure and on-site observation. After applied the developed practice program, both of the safety attitudes and safety behavior were increased to be at very good level and good level, respectively. Evaluating the follow-up unsafe records, it was found that the injury was reduced from 0.11 to 0 case/month, the medical treatment case was reduced from 0.22 to 0 case/month and the first aid case was reduced from 1 to 0.33 case/month. The developed safety working practice was successfully implemented to Thai industrial operators.