Abstract: This study was aimed to measure effective transverse
relaxation rates (R2*) in the liver and muscle of normal New Zealand
White (NZW) rabbits. R2* relaxation rate has been widely used in
various hepatic diseases for iron overload by quantifying iron contents
in liver. R2* relaxation rate is defined as the reciprocal of T2*
relaxation time and mainly depends on the constituents of tissue.
Different tissues would have different R2* relaxation rates. The signal
intensity decay in Magnetic resonance imaging (MRI) may be
characterized by R2* relaxation rates. In this study, a 1.5T GE Signa
HDxt whole body MR scanner equipped with an 8-channel high
resolution knee coil was used to observe R2* values in NZW rabbit’s
liver and muscle. Eight healthy NZW rabbits weighted 2 ~ 2.5 kg were
recruited. After anesthesia using Zoletil 50 and Rompun 2% mixture,
the abdomen of rabbit was landmarked at the center of knee coil to
perform 3-plane localizer scan using fast spoiled gradient echo
(FSPGR) pulse sequence. Afterwards, multi-planar fast gradient echo
(MFGR) scans were performed with 8 various echo times (TEs) to
acquire images for R2* measurements. Regions of interest (ROIs) at
liver and muscle were measured using Advantage workstation.
Finally, the R2* was obtained by a linear regression of ln(sı) on TE.
The results showed that the longer the echo time, the smaller the signal
intensity. The R2* values of liver and muscle were 44.8 ± 10.9 s-1 and
37.4 ± 9.5 s-1, respectively. It implies that the iron concentration of
liver is higher than that of muscle. In conclusion, the more the iron
contents in tissue, the higher the R2*. The correlations between R2*
and iron content in NZW rabbits might be valuable for further
exploration.
Abstract: High Performance Liquid Chromatography (HPLC)
method was developed and validated for simultaneous estimation of
6-Gingerol(6G) and 6-Shogaol(6S) in joint pain relief gel containing
ginger extract. The chromatographic separation was achieved by
using C18 column, 150 x 4.6mm i.d., 5μ Luna, mobile phase
containing acetonitrile and water (gradient elution). The flow rate
was 1.0 ml/min and the absorbance was monitored at 282 nm. The
proposed method was validated in terms of the analytical parameters
such as specificity, accuracy, precision, linearity, range, limit of
detection (LOD), limit of quantification (LOQ), and determined
based on the International Conference on Harmonization (ICH)
guidelines. The linearity ranges of 6G and 6S were obtained over 20-
60 and 6-18 μg/ml respectively. Good linearity was observed over the
above-mentioned range with linear regression equation Y= 11016x-
23778 for 6G and Y = 19276x-19604 for 6S (x is concentration of
analytes in μg/ml and Y is peak area). The value of correlation
coefficient was found to be 0.9994 for both markers. The limit of
detection (LOD) and limit of quantification (LOQ) for 6G were
0.8567 and 2.8555 μg/ml and for 6S were 0.3672 and 1.2238 μg/ml
respectively. The recovery range for 6G and 6S were found to be
91.57 to 102.36 % and 84.73 to 92.85 % for all three spiked levels.
The RSD values from repeated extractions for 6G and 6S were 3.43
and 3.09% respectively. The validation of developed method on
precision, accuracy, specificity, linearity, and range were also
performed with well-accepted results.
Abstract: This paper discusses the thematic structure of Yoruba
popular music of Southwest Nigeria. It examines the use of themes
and variations in early and contemporary Juju music. The work is an
outcome of a research developed by the author in his doctoral studies
at the University of Lagos, Nigeria, with the aim of analyzing the
thematic and motivic developments in Yoruba popular genres.
Observations, interviews, live recordings and CDs were used as
methods for eliciting information. Field recordings and CDs of
selected musical samples were also transcribed and notated. The
research established the prevalent use of string of themes by Juju
musicians as a compositional technique in moving from one musical
section to another, as they communicate the verbal messages in their
song. These themes consist of the popular ‘call and response’ form
found in most African music, analogous to the western ‘subject and
answer’ style of the fugue or sonata form, although without the tonic–
dominant relations. Due to the short and repetitive form of African
melodies and rhythms, a theme is restated as a variation, where its
rhythmic and melodic motifs are stylistically developed and repeated,
but still retaining its recognizable core musical structure. The
findings of this study showed that Juju musicians generally often
employ a thematic plan where new themes are used to arrange the
songs into sections, and each theme is developed into variations in
order to further expand the music, eliminate monotony, and create
musical aesthetics, serving as hallmark of its musical identity. The
study established the musical and extra-musical attributes of the
genre, while recommending further research towards analyzing the
various compositional techniques employed in African popular
genres.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: The aim of sustainable architecture is to design
buildings with the least adverse effects on the environment and
provide better conditions for people. What building forms make the
best use of land? This question was addressed in the late 1960s at the
center of Land Use and Built Form Studies in Cambridge. This led to
a number of influential papers which had a great influence on the
practice of urban design. This paper concentrates on the results of
sustainability caused by climatic conditions in Iranian traditional
architecture in hot-arid regions. As people spent a significant amount
of their time in houses, it was very important to have such houses to
fulfill their needs physically and spiritually as well as satisfying their
cultural and religious aspects of their lifestyles. In a vast country such
as Iran with different climatic zones, traditional builders have
presented series of logical solutions for human comfort. These
solutions have been able to response to the environmental problems
for a long period of time. As a result, by considering the experience
in traditional architecture of hot–arid climate in Iran, it is possible to
attain sustainable architecture.
Abstract: This paper focuses on the questions raised through the
work of Unit 5: ‘In/Out Crisis, emergent and adaptive’; an
architectural research-based studio at [ARC] University of Nicosia. Students were asked to delve into state of Art Technologies in
order to propose sustainable Emergent and Adaptive Architectures
and Urbanities, the resulting unprecedented spatial conditions and
atmospheres of the emergent new ways of living are deemed to be the
ultimate aim of the investigation. Students explored a variety of sites
and crisis conditions seen through their primary ingredient identified
as soil, water and air and their paired combination. Within this
methodology, crisis is seen as a mechanism for allowing an
emergence of new and fascinating ultimate sustainable future cultures
and cities by taking advantage of the primary materiality of the sites.
Abstract: The paper will focus on the strategic development
deriving from the evolution of the traditional courtyard spatial
organization towards a new, contemporary sustainable way of living.
New sustainable approaches that engulf the social issues, the notion
of place, the understanding of weather architecture blended together
with the bioclimatic behavior will be seen through a series of
experimental case studies in the island of Cyprus, inspired and
originated from its traditional wisdom, ranging from small scale of
living to urban interventions. Weather and nature will be seen as co-architectural authors with
architects. Furthermore, the building will be seen not as an object but
rather as a vessel of human activities. This will further enhance the
notion of merging the material and immaterial, the built and unbuilt,
subject-human, and the object-building. This eventually will enable
to generate the discussion of the understanding of the building in
relation to the place and its inhabitants, where the human topography
is more important than the material topography. The specificities of
the divided island and the dealing with sites that are in vicinity with
the diving Green Line will further trigger explorations dealing with
the regeneration issues and the social sustainability offering
unprecedented opportunities for innovative sustainable ways of
living. Opening up a discourse with premises of weather-nature, materialimmaterial,
human-material topographies in relation to the contested
sites of the borders will lead us to develop innovative strategies for a
profound, both technical and social sustainability, which fruitfully
yields to innovative living built environments, responding to the ever
changing environmental and social needs. As a starting point, a case study in Kaimakli in Nicosia, a
refurbishment with an extension of a traditional house, already
engulfs all the traditional/ vernacular wisdom of the bioclimatic
architecture. The project focusses on the direct and quite obvious
bioclimatic features such as south orientation and cross ventilation.
Furthermore, it tries to reinvent the adaptation of these parameters in
order to turn the whole house to a contemporary living environment.
In order to succeed this, evolutions of traditional architectural
elements and spatial conditions are integrated in a way that does not
only respond to some certain weather conditions, but they integrate
and blend the weather within the built environment. A series of
innovations aiming at maximum flexibility is proposed. The house
can finally be transformed into a winter enclosure, while for the most
part of the year it turns into a ‘camping’ living environment. Parallel to experimental interventions in existing traditional units,
we will proceed examining the implementation of the same
developed methodology in designing living units and complexes.
Malleable courtyard organizations that attempt to blend the
traditional wisdom with the contemporary needs for living, the
weather and nature with the built environment will be seen tested in
both horizontal and vertical developments. Social activities are seen as directly affected and forged by the
weather conditions thus generating a new social identity of people where people are directly involved and interacting with the weather.
The human actions and interaction with the built, material
environment in order to respond to weather will be seen as the result
of balancing the social with the technological sustainability, the
immaterial, and the material aspects of the living environment.
Abstract: Green concrete are generally composed of recycling
materials as hundred or partial percent substitutes for aggregate,
cement, and admixture in concrete. To reduce greenhouse gas
emissions, efforts are needed to develop environmentally friendly
construction materials. Using of fly ash based geopolymer as an
alternative binder can help reduce CO2 emission of concrete. The
binder of geopolymer concrete is different from the ordinary Portland
cement concrete. Geopolymer Concrete specimens were prepared
with different concentration of NaOH solution M10, M14, and, M16
and cured at 60ºC in duration of 24 hours and 8 hours, in addition to
the curing in direct sunlight. Thus, it is necessary to study the effects
of the geopolymer binder on the behavior of concrete. Concrete is
made by using geopolymer technology is environmental friendly and
could be considered as part of the sustainable development. In this
study, the Local Alkaline Activator in Egypt and crashed stone as
coarse aggregate in fly ash based-geopolymer concrete was
investigated. This paper illustrates the development of mechanical
properties. Since the gained compressive strength for geopolymer
concrete at 28 days was in the range of 22.5MPa – 43.9MPa.
Abstract: This article proposes a hybrid algorithm for spectrum
allocation in cognitive radio networks based on the algorithms
Analytical Hierarchical Process (AHP) and Technique for Order of
Preference by Similarity to Ideal Solution (TOPSIS) to improve the
performance of the spectrum mobility of secondary users in cognitive
radio networks. To calculate the level of performance of the proposed algorithm a
comparative analysis between the proposed AHP-TOPSIS, Grey
Relational Analysis (GRA) and Multiplicative Exponent Weighting
(MEW) algorithm is performed. Four evaluation metrics are used.
These metrics are accumulative average of failed handoffs,
accumulative average of handoffs performed, accumulative average
of transmission bandwidth, and accumulative average of the
transmission delay. The results of the comparison show that AHP-TOPSIS Algorithm
provides 2.4 times better performance compared to a GRA Algorithm
and, 1.5 times better than the MEW Algorithm.
Abstract: Local steel slag is produced as a by-product during the
oxidation of steel pellets in an electric arc furnace. Using local steel
slag waste as a hundred substitutes of crashed stone in construction
materials would resolve the environmental problems caused by the
large-scale depletion of the natural sources of crashed stone. This
paper reports the experimental study to investigate the influence of a
hundred replacement of crashed stone as a coarse aggregate with
local steel slag, on the fresh and hardened geopolymer concrete
properties. The investigation includes traditional testing of hardening
concrete, for selected mixes of cement and geopolymer concrete. It
was found that local steel slag as a coarse aggregate enhanced the
slump test of the fresh state of cement and geopolymer concretes.
Nevertheless, the unit weight of concretes was affected. Meanwhile,
the good performance was observed when fly ash used as geopolymer
concrete based.
Abstract: This qualitative case study seeks to understand and
explain the deployment of radio frequency identification (RFID)
systems in two countries (i.e., in Taiwan for the adoption of electric
scooters and in Finland for supporting glass bottle recycling) using
the “Technology-Organization-Environment” theoretical framework.
This study also seeks to highlight the relevance and importance of
pursuing environmental sustainability in firms and in society in
general due to the social urgency of the issues involved.
Abstract: Sweep frequency response analysis has been turning
out a powerful tool for investigation of mechanical as well as
electrical integration of transformers. In this paper various aspect of
practical application of SFRA has been studied. Open circuit and
short circuit measurement were done on different phases of high
voltage and low voltage winding. A case study was presented for the
transformer of rating 31.5 MVA for various frequency ranges. A
clear picture was presented for sub- frequency ranges for HV as well
as LV winding. The main motive of work is to investigate high
voltage short circuit response. The theoretical concept about SFRA
responses is validated with expert system software results.
Abstract: Unemployment among the youth is a significant
problem in South Africa. Large corporations and the public sector
simply cannot create enough jobs. Too many youths in South Africa
currently do not consider entrepreneurship as an option in order to
become independent. Unlike the youth of the Netherlands, South
African youth prefer to find employment in the public or private
sector. The Netherlands has a much lower unemployment rate than
South Africa and the Dutch are generally very entrepreneurial. From
early on, entrepreneurship is considered a desirable career option in
the Netherlands. The purpose of this study was to determine whether
there is a difference in the perceptions of some Dutch and South
African students in terms of unemployment and entrepreneurship.
Questionnaires were distributed to students at the North West
University's Vaal Triangle campus in Vanderbijlpark in Gauteng,
South Africa and the Technical University of Delft in the
Netherlands. A descriptive statistical analysis approach was followed
and the means for the independent questions were calculated. The
results demonstrate that the Dutch students are not as concerned
about unemployment after completion of their studies as this is not as
significant a problem as it is in South Africa. Both groups had
positive responses towards the posed questions, but the South African
group felt more strongly about the issues. Both groups of students felt
that there was a need for more practical entrepreneurship training.
The South African education system should focus on practical
entrepreneurship training from a young age.
Abstract: The use of solar energy as a source for pumping water
is one of the promising areas in the photovoltaic (PV) application.
The energy of photovoltaic pumping systems (PVPS) can be widely
improved by employing an MPPT algorithm. This will lead
consequently to maximize the electrical motor speed of the system.
This paper presents a modified incremental conductance (IncCond)
MPPT algorithm with direct control method applied to a standalone
PV pumping system. The influence of the algorithm parameters on
system behavior is investigated and compared with the traditional
(INC) method. The studied system consists of a PV panel, a DC-DC
boost converter, and a PMDC motor-pump. The simulation of the
system by MATLAB-SIMULINK is carried out. Simulation results
found are satisfactory.
Abstract: A retrospective study conducted at Christian Medical
College (CMC) Teaching Hospital, Vellore, India on 14th August
2014 to assess the accuracy of clinically estimated foetal weight upon
labour admission. Estimating foetal weight is a crucial factor in
assessing maternal and foetal complications during and after labour.
Medical notes of ninety-eight postnatal women who fulfilled the
inclusion criteria were studied to evaluate the correlation between
their recorded Estimated Foetal Weight (EFW) on admission and
actual birth weight (ABW) of the newborn after delivery. Data
concerning maternal and foetal demographics was also noted.
Accuracy was determined by absolute percentage error and
proportion of estimates within 10% of ABW. Actual birth weights
ranged from 950-4080g. A strong positive correlation between EFW
and ABW (r=0.904) was noted. Term deliveries (≥40 weeks) in the
normal weight range (2500-4000g) had a 59.5% estimation accuracy
(n=74) compared to pre-term (4000g) were underestimated by 25% (n=3) and low birthweight
(LBW) babies were overestimated by 12.7% (n=9). Registrars who
estimated foetal weight were accurate in babies within normal weight
ranges. However, there needs to be an improvement in predicting
weight of macrosomic and LBW foetuses. We have suggested the use
of an amended version of the Johnson’s formula for the Indian
population for improvement and a need to re-audit once
implemented.
Abstract: Polycyclic Aromatic Hydrocarbons (PAHs) are
formed mainly because of incomplete combustion of organic
materials during industrial, domestic activities or natural occurrence.
Their toxicity and contamination of terrestrial and aquatic ecosystem
have been established. However, with limited validity index, previous
research has focused on PAHs isomer pair ratios of variable
physicochemical properties in source identification. The objective of
this investigation was to determine the empirical validity of Pearson
Correlation Coefficient (PCC) and Cluster Analysis (CA) in PAHs
source identification along soil samples of different land uses.
Therefore, 16 PAHs grouped, as Endocrine Disruption Substances
(EDSs) were determined in 10 sample stations in top and sub soils
seasonally. PAHs was determined the use of Varian 300 gas
chromatograph interfaced with flame ionization detector. Instruments
and reagents used are of standard and chromatographic grades
respectively. PCC and CA results showed that the classification of
PAHs along pyrolitic and petrogenic organics used in source
signature is about the predominance PAHs in environmental matrix.
Therefore, the distribution of PAHs in the studied stations revealed
the presence of trace quantities of the vast majority of the sixteen
PAHs, which may ultimately inhabit the actual source signature
authentication. Therefore, factors to be considered when evaluating
possible sources of PAHs could be; type and extent of bacterial
metabolism, transformation products/substrates, and environmental
factors such as salinity, pH, oxygen concentration, nutrients, light
intensity, temperature, co-substrates, and environmental medium are
hereby recommended as factors to be considered when evaluating
possible sources of PAHs.
Abstract: Paper deals with the modeling and simulation of energy consumption and GHG production of two different modes of regional passenger transport – road and railway. These two transport modes use the same type of fuel – diesel. Modeling and simulation of the energy consumption in transport is often used due to calculation satisfactory accuracy and cost efficiency. Paper deals with the calculation based on EN standards and information collected from technical information from vehicle producers and characteristics of tracks. Calculation included maximal theoretical capacity of bus and train and real passenger’s measurement from operation. Final energy consumption and GHG production is calculated by using software simulation. In evaluation of the simulation is used system “well to wheel”.
Abstract: Polymorphism is one of the main pillars of objectoriented
paradigm. It induces hidden forms of class dependencies
which may impact software quality, resulting in higher cost factor for
comprehending, debugging, testing, and maintaining the software. In
this paper, a new cognitive complexity metric called Cognitive
Weighted Polymorphism Factor (CWPF) is proposed. Apart from the
software structural complexity, it includes the cognitive complexity
on the basis of type. The cognitive weights are calibrated based on 27
empirical studies with 120 persons. A case study and experimentation
of the new software metric shows positive results. Further, a
comparative study is made and the correlation test has proved that
CWPF complexity metric is a better, more comprehensive, and more
realistic indicator of the software complexity than Abreu’s
Polymorphism Factor (PF) complexity metric.
Abstract: Many herbal medicinal products are considered
potential anti-hypercholesterolemic agents with encouraging safety
profiles, however only a limited amount of clinical research exists to
support their efficacy. The present study was designed to compare the
antihypercholesterolemic and antioxidant activities of the crude
ethanolic extracts of Citrus reticulata fruit peel, Zingiber officinale
rhizome and Sesamum indicum seeds. Forty-five rats were used throughout the experiment which are
extended for four weeks. These were divided into nine groups, five
rats per each group as follows; group 1 was the normal control group
(rats only fed standard normal rat diet), group 2 was the
hypercholesterolemic control group (rats fed only
hypercholesterolemic diet which contained 1% cholesterol plus 10%
saturated animal fat added to the normal rat diet), groups 3 and 4
were fed hypercholesterolemic diet in addition to Citrus reticulata
ethanolic extract at doses of (250mg/kg (group 3) and 500mg/kg
(group 4)) administered daily via oral route, groups 5 and 6 were
given hypercholesterolemic diet in addition to Zingiber officinale
ethanolic extract at doses of (250mg/kg (group 5) and 500mg/kg
(group 6)) daily through oral route, groups 7 and 8 fed on
hypercholesterolemic diet in addition to Sesamum indicum ethanolic
extract at doses of (250mg/kg (group 7) and 500mg/kg (group 8))
daily orally; and group 9 rats were given hypercholesterolemic diet in
addition to atorvastatin (0.18mg/kg) daily via oral route as a standard
reference antihypercholesterolemic drug. Blood samples from all
groups were drawn from the retro-orbital venous plexus four weeks
following treatment after overnight fasting and the lipid profile (total
cholesterol (TC), high density lipoprotein-cholesterol (HDL-C), low
density lipoprotein-cholesterol (LDL-C) and triglyceride levels) were
measured and the risk ratio (TC/HDL-C) was assessed. The
antioxidant activity of the three plants extracts was determined using
DPPH free-radical antioxidant assay. Results of in vivo and in vitro
antihypercholesterolemic and antioxidant assay respectively, revealed
that the three extracts possess comparable antioxidant and
antihypercholesterolemic activities.
Abstract: This investigation is focused on using of Mon dance
in Pathum Thani Province’s tradition and has the following
objectives: 1) to study the background of Mon dance in Pathum
Thani Province; 2) to study Mon dance in Pathum Thani Province;
and 3) to study of using Mon dance in Pathum Thani province’s
tradition. This qualitative research was conducted in Pathum Thani
province (in the central of Thailand). Data was collected from
documentary study and field data by means of observation, interview,
and group discussion. Workshops were also held with a total of 100
attendees, comprised of 20 key informants, 40 casual informants and
40 general informants. Data was validated using the triangulation
technique and the findings are presented using the descriptive
analysis. The results of the study show that the historical background
of Mon dance in Pathum Thani Province initiated during the war
evacuation from Martaban (south of Burma) to settle down in Sam
Khok, Pathum Thani Province in Ayutthaya period to Rattanakosin.
The study found that Mon dance typically consists of 12-13 dancing
process. The melodies have 12-13 songs. Piphat Mon (Mon
traditional music ensemble) is used in the performance. Performers
are dressed in Mon traditional costumes. The performers are 6-12
women and depending on the employer’s demands. Length of the
performance varies from the duration of music orchestration. Rituals
and customs performed are paying homage to teachers before the
performance. The offerings are composed of flowers, incense sticks,
candles, money gifts which are well arranged on a tray with pedestal,
and also liquors, tobaccos and pure water for asking propitiousness.
For the use of Mon dance in Pathum Thani Province’s tradition, it is
found that the dance is commonly performed in the funeral
ceremonial tradition at present because the physical postures of the
performance are considered graceful and exquisite. In addition, as for
its value, it has long been believed since the ancient times that Mon
dance was a sacred thing considered as the dignity and glorification
especially for funeral ceremonies of priest or royal hierarchy classes.
However, Mon dance has continued to be used in the traditions
associated with Mon people activities in Pathum Thani Province for
instance customary welcome for honor guest and Songkran festival.