Abstract: In this paper we develop an efficient numerical method for the finite-element model updating of damped gyroscopic systems based on incomplete complex modal measured data. It is assumed that the analytical mass and stiffness matrices are correct and only the damping and gyroscopic matrices need to be updated. By solving a constrained optimization problem, the optimal corrected symmetric damping matrix and skew-symmetric gyroscopic matrix complied with the required eigenvalue equation are found under a weighted Frobenius norm sense.
Abstract: Due to the three- dimensional flow pattern interacting with bed material, the process of local scour around bridge piers is complex. Modeling 3D flow field and scour hole evolution around a bridge pier is more feasible nowadays because the computational cost and computational time have significantly decreased. In order to evaluate local flow and scouring around a bridge pier, a completely three-dimensional numerical model, SSIIM program, was used. The model solves 3-D Navier-Stokes equations and a bed load conservation equation. The model was applied to simulate local flow and scouring around a bridge pier in a large natural river with four piers. Computation for 1 day of flood condition was carried out to predict the maximum local scour depth. The results show that the SSIIM program can be used efficiently for simulating the scouring in natural rivers. The results also showed that among the various turbulence models, the k-ω model gives more reasonable results.
Abstract: This experiment was carried out to study the effect of
AMF, drought stress and phosphorus on physiological growth indices of basil at Iran using by a split-plot design with three replications.
The main-plot factor included: two levels of irrigation regimes (control=no drought stress and irrigation after 80 evaporation=
drought stress condition) while the sub-plot factors included
phosphorus (0, 35 and 70 kg/ha) and application and non-application of Glomus fasciculatum. The results showed that total dry matter
(TDM), life area index (LAI), relative growth rate (RGR) and crop growth rate (CGR) were all highly significantly different among the
phosphorus, whereas drought stress had effect of practical
significance on TDM, LAI, RGR and CGR. The results also showed that the highest TDM, LAI, RGR and CGR were obtained from
application of Glomus fasciculatum under no-drought condition.
Abstract: In this study, the effects of machining parameters on
specific energy during surface grinding of 6061Al-SiC35P
composites are investigated. Vol% of SiC, feed and depth of cut were
chosen as process variables. The power needed for the calculation of
the specific energy is measured from the two watt meter method.
Experiments are conducted using standard RSM design called Central
composite design (CCD). A second order response surface model was
developed for specific energy. The results identify the significant
influence factors to minimize the specific energy. The confirmation
results demonstrate the practicability and effectiveness of the
proposed approach.
Abstract: This study proposes a basic molecular formula for all
proteins. A total of 10,739 proteins belonging to 9 different protein
groups classified on the basis of their functions were selected
randomly. They included enzymes, storage proteins, hormones,
signalling proteins, structural proteins, transport proteins,
immunoglobulins or antibodies, motor proteins and receptor proteins.
After obtaining the protein molecular formula using the ProtParam
tool, the H/C, N/C, O/C, and S/C ratios were determined for each
randomly selected sample. In this case, H, N, O, and S coefficients
were specified per carbon atom. Surprisingly, the results
demonstrated that H, N, O, and S coefficients for all 10,739 proteins
are similar and highly correlated. This study demonstrates that
despite differences in the structure and function, all known proteins
have a similar basic molecular formula CnH1.58 ± 0.015nN0.28 ± 0.005nO0.30
± 0.007nS0.01 ± 0.002n. The total correlation between all coefficients was
found to be 0.9999.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.
Abstract: In the present article, a new method has been developed to enhance the application of equipment monitoring, which in turn results in improving condition-based maintenance economic impact in an automobile parts manufacturing factory. This study also describes how an effective software with a simple database can be utilized to achieve cost-effective improvements in maintenance performance. The most important results of this project are indicated here: 1. 63% reduction in direct and indirect maintenance costs. 2. Creating a proper database to analyse failures. 3. Creating a method to control system performance and develop it to similar systems. 4. Designing a software to analyse database and consequently create technical knowledge to face unusual condition of the system. Moreover, the results of this study have shown that the concept and philosophy of maintenance has not been understood in most Iranian industries. Thus, more investment is strongly required to improve maintenance conditions.
Abstract: This paper presents the solution of power economic dispatch (PED) problem of generating units with valve point effects and multiple fuel options using Self-Adaptive Differential Evolution (SDE) algorithm. The global optimal solution by mathematical approaches becomes difficult for the realistic PED problem in power systems. The Differential Evolution (DE) algorithm is found to be a powerful evolutionary algorithm for global optimization in many real problems. In this paper the key parameters of control in DE algorithm such as the crossover constant CR and weight applied to random differential F are self-adapted. The PED problem formulation takes into consideration of nonsmooth fuel cost function due to valve point effects and multi fuel options of generator. The proposed approach has been examined and tested with the numerical results of PED problems with thirteen-generation units including valve-point effects, ten-generation units with multiple fuel options neglecting valve-point effects and ten-generation units including valve-point effects and multiple fuel options. The test results are promising and show the effectiveness of proposed approach for solving PED problems.
Abstract: The main aim is to perform mutational analysis of CTLA4 gene Exon 1 in SLE patients. A total of 61 SLE patients fulfilling “American College of Rheumatology (ACR) criteria" and 61 controls were enrolled in this study. The region of CTLA4 gene exon 1 was amplified by using Step-down PCR technique. Extracted DNA of band 354 bp was sequenced to analyze mutations in the exon-1 of CTLA-4 gene. Further, protein sequences were identified from nucleotide sequences of CTLA4 Exon 1 by using Expasy software and through Blast P software it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. No variations were found after patients sequences were compared with that of the control sequence. Furthermore it was found that CTLA4 protein sequences of Pakistani SLE patients were similar to that of Chinese SLE population. Thus CTLA4 gene may not be responsible for an autoimmune disease SLE.
Abstract: The study investigated the hydrophilic to hydrophobic
transition of modified polyacrylamide hydrogel with the inclusion of
N-isopropylacrylamide (NIAM). The modification was done by
mimicking micellar polymerization, which resulted in better
arrangement of NIAM chains in the polyacrylamide network. The
degree of NIAM arrangement is described by NH number. The
hydrophilic to hydrophobic transition was measured through the
partition coefficient, K, of Orange II and Methylene Blue in hydrogel
and in water. These dyes were chosen as a model for solutes with
different degree of hydrophobicity. The study showed that the
hydrogel with higher NH values resulted in better solubility of both
dyes. Moreover, in temperature above the lower critical solution
temperature (LCST) of Poly(N-isopropylacrylamide) (PNIAM)also
caused the collapse of NIPAM chains which results in a more
hydrophobic environment that increases the solubility of Methylene
Blue and decreases the solubility of Orange II in the hydrogels with
NIPAM present.
Abstract: In this paper a mixed method by combining an evolutionary and a conventional technique is proposed for reduction of Single Input Single Output (SISO) continuous systems into Reduced Order Model (ROM). In the conventional technique, the mixed advantages of Mihailov stability criterion and continued Fraction Expansions (CFE) technique is employed where the reduced denominator polynomial is derived using Mihailov stability criterion and the numerator is obtained by matching the quotients of the Cauer second form of Continued fraction expansions. Then, retaining the numerator polynomial, the denominator polynomial is recalculated by an evolutionary technique. In the evolutionary method, the recently proposed Differential Evolution (DE) optimization technique is employed. DE method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. The proposed method is illustrated through a numerical example and compared with ROM where both numerator and denominator polynomials are obtained by conventional method to show its superiority.
Abstract: In this paper we propose an intelligent agent approach
to control the electric power grid at a smaller granularity in order to
give it self-healing capabilities. We develop a method using the
influence model to transform transmission substations into
information processing, analyzing and decision making (intelligent
behavior) units. We also develop a wireless communication method
to deliver real-time uncorrupted information to an intelligent
controller in a power system environment. A combined networking
and information theoretic approach is adopted in meeting both the
delay and error probability requirements. We use a mobile agent
approach in optimizing the achievable information rate vector and in
the distribution of rates to users (sensors). We developed the concept
and the quantitative tools require in the creation of cooperating semiautonomous
subsystems which puts the electric grid on the path
towards intelligent and self-healing system.
Abstract: Nanoemulsions are a class of emulsions with a droplet
size in the range of 50–500 nm and have attracted a great deal of
attention in recent years because it is unique characteristics. The
physicochemical properties of nanoemulsion suggests that it can be
successfully used to recover the residual oil which is trapped in the
fine pore of reservoir rock by capillary forces after primary and
secondary recovery. Oil-in-water nanoemulsion which can be formed
by high-energy emulsification techniques using specific surfactants
can reduce oil-water interfacial tension (IFT) by 3-4 orders of
magnitude. The present work is aimed on characterization of oil-inwater
nanoemulsion in terms of its phase behavior, morphological
studies; interfacial energy; ability to reduce the interfacial tension and
understanding the mechanisms of mobilization and displacement of
entrapped oil blobs by lowering interfacial tension both at the
macroscopic and microscopic level. In order to investigate the
efficiency of oil-water nanoemulsion in enhanced oil recovery
(EOR), experiments were performed to characterize the emulsion in
terms of their physicochemical properties and size distribution of the
dispersed oil droplet in water phase. Synthetic mineral oil and a series
of surfactants were used to prepare oil-in-water emulsions.
Characterization of emulsion shows that it follows pseudo-plastic
behaviour and drop size of dispersed oil phase follows lognormal
distribution. Flooding experiments were also carried out in a
sandpack system to evaluate the effectiveness of the nanoemulsion as
displacing fluid for enhanced oil recovery. Substantial additional
recoveries (more than 25% of original oil in place) over conventional
water flooding were obtained in the present investigation.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, a source of alternating current (50 Hz) and a clear victim in a certain distance from the source is placed. With this simple model, the effects of electromagnetic radiation from the source to the victim will be investigated and several methods to reduce these effects have been presented. Therefore passive and active shields have been used. In some steps, shielding effectiveness of proposed shields will be compared. . It should be noted that simulations have been done by the finite element method (FEM).
Abstract: The purpose of semantic web research is to transform
the Web from a linked document repository into a distributed knowledge base and application platform, thus allowing the vast range of available information and services to be more efficiently
exploited. As a first step in this transformation, languages such as
OWL have been developed. Although fully realizing the Semantic Web still seems some way off, OWL has already been very
successful and has rapidly become a defacto standard for ontology
development in fields as diverse as geography, geology, astronomy,
agriculture, defence and the life sciences. The aim of this paper is to classify key concepts of Semantic Web as well as introducing a new
practical approach which uses these concepts to outperform Word Wide Web.
Abstract: Hidden Markov Model (HMM) is a stochastic method
which has been used in various signal processing and character
recognition. This study proposes to use HMM to recognize Javanese
characters from a number of different handwritings, whereby HMM
is used to optimize the number of state and feature extraction. An
85.7 % accuracy is obtained as the best result in 16-stated vertical
model using pure HMM. This initial result is satisfactory for
prompting further research.
Abstract: We measured the major and trace element contents
and Rb-Sr isotopic compositions of 12 tektites from the Maoming
area, Guandong province (south China). All the samples studied are
splash-form tektites which show pitted or grooved surfaces with
schlieren structures on some surfaces. The trace element ratios Ba/Rb
(avg. 4.33), Th/Sm (avg. 2.31), Sm/Sc (avg. 0.44), Th/Sc (avg. 1.01) ,
La/Sc (avg. 2.86), Th/U (avg. 7.47), Zr/Hf (avg. 46.01) and the rare
earth elements (REE) contents of tektites of this study are similar to the
average upper continental crust. From the chemical composition, it is
suggested that tektites in this study are derived from similar parental
terrestrial sedimentary deposit which may be related to post-Archean
upper crustal rocks. The tektites from the Maoming area have high
positive εSr(0) values-ranging from 176.9~190.5 which indicate that
the parental material for these tektites have similar Sr isotopic
compositions to old terrestrial sedimentary rocks and they were not
dominantly derived from recent young sediments (such as soil or
loess). The Sr isotopic data obtained by the present study support the
conclusion proposed by Blum et al. (1992)[1] that the depositional age
of sedimentary target materials is close to 170Ma (Jurassic). Mixing
calculations based on the model proposed by Ho and Chen (1996)[2]
for various amounts and combinations of target rocks indicate that the
best fit for tektites from the Maoming area is a mixture of 40% shale,
30% greywacke, 30% quartzite.
Abstract: Traffic management in an urban area is highly facilitated by the knowledge of the traffic conditions in every street or highway involved in the vehicular mobility system. Aim of the paper is to propose a neuro-fuzzy approach able to compute the main parameters of a traffic system, i.e., car density, velocity and flow, by using the images collected by the web-cams located at the crossroads of the traffic network. The performances of this approach encourage its application when the traffic system is far from the saturation. A fuzzy model is also outlined to evaluate when it is suitable to use more accurate, even if more time consuming, algorithms for measuring traffic conditions near to saturation.
Abstract: This paper presents an indirect adaptive stabilization
scheme for first-order continuous-time systems under saturated input
which is described by a sigmoidal function. The singularities are
avoided through a modification scheme for the estimated plant
parameter vector so that its associated Sylvester matrix is guaranteed
to be non-singular and then the estimated plant model is controllable.
The modification mechanism involves the use of a hysteresis
switching function. An alternative hybrid scheme, whose estimated
parameters are updated at sampling instants is also given to solve a
similar adaptive stabilization problem. Such a scheme also uses
hysteresis switching for modification of the parameter estimates so as
to ensure the controllability of the estimated plant model.