Abstract: The objective of this paper is to present a research
study of the convectors that are used for heating or cooling of the
living room or industrial halls. The key points are experimental
measurement and comprehensive numerical simulation of the flow
coming throughout the part of the convector such as heat exchanger,
input from the fan etc.. From the obtained results, the components of
the convector are optimized in sense to increase thermal power
efficiency due to improvement of heat convection or reduction of air
drag friction. Both optimized aspects are leading to the more
effective service conditions and to energy saving. The significant part
of the convector research is a design of the unique measurement
laboratory and adopting measure techniques. The new laboratory
provides possibility to measure thermal power efficiency and other
relevant parameters under specific service conditions of the
convectors.
Abstract: WLAN Positioning has been presented by many
approaches in literatures using the characteristics of Received Signal
Strength (RSS), Time of Arrival (TOA) or Time Difference of
Arrival (TDOA), Angle of Arrival (AOA) and cell ID. Among these,
RSS approach is the simplest method to implement because there is
no need of modification on both access points and client devices
whereas its accuracy is terrible due to physical environments. For
TOA or TDOA approach, the accuracy is quite acceptable but most
researches have to modify either software or hardware on existing
WLAN infrastructure. The scales of modifications are made on only
access card up to the changes in protocol of WLAN. Hence, it is an
unattractive approach to use TOA or TDOA for positioning system.
In this paper, the new concept of merging both RSS and TOA
positioning techniques is proposed. In addition, the method to
achieve TOA characteristic for positioning WLAN user without any
extra modification necessarily appended in the existing system is
presented. The measurement results confirm that the proposed
technique using both RSS and TOA characteristics provides better
accuracy than using only either RSS or TOA approach.
Abstract: Collateralized Debt Obligations are not as widely used
nowadays as they were before 2007 Subprime crisis. Nonetheless
there remains an enthralling challenge to optimize cash flows
associated with synthetic CDOs. A Gaussian-based model is used
here in which default correlation and unconditional probabilities of
default are highlighted. Then numerous simulations are performed
based on this model for different scenarios in order to evaluate the
associated cash flows given a specific number of defaults at different
periods of time. Cash flows are not solely calculated on a single
bought or sold tranche but rather on a combination of bought and
sold tranches. With some assumptions, the simplex algorithm gives
a way to find the maximum cash flow according to correlation of
defaults and maturities. The used Gaussian model is not realistic in
crisis situations. Besides present system does not handle buying or
selling a portion of a tranche but only the whole tranche. However the
work provides the investor with relevant elements on how to know
what and when to buy and sell.
Abstract: Semiconductor detector arrays are widely used in
high-temperature plasma diagnostics. They have a fast response,
which allows observation of many processes and instabilities in
tokamaks. In this paper, there are reviewed several diagnostics based
on semiconductor arrays as cameras, AXUV photodiodes (referred
often as fast “bolometers") and detectors of both soft X-rays and
visible light installed on the COMPASS tokamak recently. Fresh
results from both spring and summer campaigns in 2012 are
introduced. Examples of the utilization of the detectors are shown on
the plasma shape determination, fast calculation of the radiation
center, two-dimensional plasma radiation tomography in different
spectral ranges, observation of impurity inflow, and also on
investigation of MHD activity in the COMPASS tokamak discharges.
Abstract: Thailand-s health system is challenged by the rising
number of patients and decreasing ratio of medical
practitioners/patients, especially in rural areas. This may tempt
inexperienced GPs to rush through the process of anamnesis with the
risk of incorrect diagnosis. Patients have to travel far to the hospital
and wait for a long time presenting their case. Many patients try to
cure themselves with traditional Thai medicine. Many countries are
making use of the Internet for medical information gathering,
distribution and storage. Telemedicine applications are a relatively
new field of study in Thailand; the infrastructure of ICT had
hampered widespread use of the Internet for using medical
information. With recent improvements made health and technology
professionals can work out novel applications and systems to help
advance telemedicine for the benefit of the people. Here we explore
the use of telemedicine for people with health problems in rural areas
in Thailand and present a Telemedicine Diagnosis System for Rural
Thailand (TEDIST) for diagnosing certain conditions that people
with Internet access can use to establish contact with Community
Health Centers, e.g. by mobile phone. The system uses a Web-based
input method for individual patients- symptoms, which are taken by
an expert system for the analysis of conditions and appropriate
diseases. The analysis harnesses a knowledge base and a backward
chaining component to find out, which health professionals should be
presented with the case. Doctors have the opportunity to exchange
emails or chat with the patients they are responsible for or other
specialists. Patients- data are then stored in a Personal Health Record.
Abstract: CDMA cellular networks support soft handover,
which guarantees the continuity of wireless services and enhanced
communication quality. Cellular networks support multimedia
services under varied propagation environmental conditions. In this
paper, we have shown the effect of characteristic parameters of the
cellular environments on the soft handover performance. We
consider path loss exponent, standard deviation of shadow fading and
correlation coefficient of shadow fading as the characteristic
parameters of the radio propagation environment. A very useful
statistical measure for characterizing the performance of mobile radio
system is the probability of outage. It is shown through numerical
results that above parameters have decisive effect on the probability
of outage and hence the overall performance of the soft handover
algorithm.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: Based on a global kinetics of direct dimethyl ether (DME) synthesis process from syngas, a steady-state one-dimensional mathematical model for the bubble column slurry reactor (BCSR) has been established. It was built on the assumption of plug flow of gas phase, sedimentation-dispersion model of catalyst grains and isothermal chamber regardless of reaction heats and rates for the design of an industrial scale bubble column slurry reactor. The simulation results indicate that higher pressure and lower temperature were favorable to the increase of CO conversion, DME selectivity, products yield and the height of slurry bed, which has a coincidence with the characteristic of DME synthesis reaction system, and that the height of slurry bed is lessen with the increasing of operation temperature in the range of 220-260℃. CO conversion, the optimal operation conditions in BCSR were proposed.
Abstract: For broadband wireless mobile communication
systems the orthogonal frequency division multiplexing (OFDM) is a
suitable modulation scheme. The frequency offset between
transmitter and receiver local oscillator is main drawback of OFDM
systems, which causes intercarrier interference (ICI) in the
subcarriers of the OFDM system. This ICI degrades the bit error rate
(BER) performance of the system. In this paper an improved self-ICI
cancellation scheme is proposed to improve the system performance.
The proposed scheme is based on discrete Fourier transform-inverse
discrete Fourier transform (DFT-IDFT). The simulation results show
that there is satisfactory improvement in the bit error rate (BER)
performance of the present scheme.
Abstract: This paper presents a large scale, quantitative investigation of the impact of discipline differences on the student experience of using an online learning environment (OLE). Based on a representative sample of 2526 respondents, a number of significant differences in the mean rating by broad discipline area of the importance of, and satisfaction with, a range of elements of an OLE were found. Broadly speaking, the Arts and Science and Technology discipline areas reported the lowest importance and satisfaction ratings for the OLE, while the Health and Behavioural Sciences area was the most satisfied with the OLE. A number of specific, systematic discipline differences are reported and discussed. Compared to the observed significant differences in mean importance ratings, there were fewer significant differences in mean satisfaction ratings, and those that were observed were less systematic than for importance ratings.
Abstract: The V-notches are most possible case for initiation of cracks in parts. The specifications of cracks on the tip of the notch will be influenced via opening angle, tip radius and depth of V-notch. In this study, the effects of V-notch-s opening angle on stress intensity factor and T-stress of crack on the notch has been investigated. The experiment has been done in different opening angles and various crack length in mode (I) loading using Photoelasticity method. The results illustrate that while angle increases in constant crack-s length, SIF and T-stress will decrease. Beside, the effect of V-notch angle in short crack is more than long crack. These V-notch affects are negligible by increasing the length of crack, and the crack-s behavior can be considered as a single-edge crack specimen. Finally, the results have been evaluated with numerical finite element analysis and good agreement was obvious.
Abstract: A cell-centered finite volume scheme for discretizing diffusion operators on distorted quadrilateral meshes has recently been designed and added to APMFCG to enable that code to be used as a tool for studying explosive magnetic flux compression generators. This paper describes this scheme. Comparisons with analytic results for 2-D test cases are presented, as well as 2-D results from a test of a "realistic" generator configuration.
Abstract: A number of studies highlighted problems related to
ERP systems, yet, most of these studies focus on the problems during
the project and implementation stages but not during the postimplementation
use process. Problems encountered in the process of
using ERP would hinder the effective exploitation and the extended
and continued use of ERP systems and their value to organisations.
This paper investigates the different types of problems users
(operational, supervisory and managerial) faced in using ERP and
how 'feral system' is used as the coping mechanism. The paper
adopts a qualitative method and uses data collected from two cases
and 26 interviews, to inductively develop a casual network model of
ERP usage problem and its coping mechanism. This model classified
post ERP usage problems as data quality, system quality, interface
and infrastructure. The model is also categorised the different coping
mechanism through use of 'feral system' inclusive of feral
information system, feral data and feral use of technology.
Abstract: Computing and maintaining network structures for efficient
data aggregation incurs high overhead for dynamic events
where the set of nodes sensing an event changes with time. Moreover,
structured approaches are sensitive to the waiting time that is used
by nodes to wait for packets from their children before forwarding
the packet to the sink. An optimal routing and data aggregation
scheme for wireless sensor networks is proposed in this paper. We
propose Tree on DAG (ToD), a semistructured approach that uses
Dynamic Forwarding on an implicitly constructed structure composed
of multiple shortest path trees to support network scalability. The key
principle behind ToD is that adjacent nodes in a graph will have
low stretch in one of these trees in ToD, thus resulting in early
aggregation of packets. Based on simulations on a 2,000-node Mica2-
based network, we conclude that efficient aggregation in large-scale
networks can be achieved by our semistructured approach.
Abstract: Today global warming, climate change and energy supply are of greater concern as it is widely realized that the planet earth does not provide an infinite capacity for absorbing human industrialization in the 21st century. The aim of this paper is to analyze upstream and downstream electricity production in selected case studies: a coal power plant, a pump system and a microwave oven covering and consumption to explore the position of energy efficiency in engineering sustainability. Collectively, the analysis presents energy efficiency as a major pathway towards sustainability that requires an inclusive and a holistic supply chain response in the engineering design process.
Abstract: Polylactic acid-g-polyvinyl acetate (PLLA-g-PVAc)
was used as a compatibilizer for 50/50 starch/PLLA blend. PLLA-g-
PVAc with different mol% of PVAc contents were prepared by
grafting PVAc onto PLLA backbone via free radical polymerization
in solution process. Various conditions such as type and the amount
of initiator, monomer concentration, polymerization time and
temperature were studied. Results showed that the highest mol% of
PVAc grafting (16 mol%) was achieved by conducting graft
copolymerization in toluene at 110°C for 10 h using DCP as an
initiator. Chemical structure of the PVAc grafted PLLA was
confirmed by 1H NMR. Blending of modified starch and PLLA in the
presence compatibilizer with different amounts and mol% PVAc was
acquired using internal mixer at 160°C for 15 min. Effects of PVAc
content and the amount of compatibilizer on mechanical properties of
polymer blend were studied. Results revealed that tensile strength and
tensile modulus of polymer blend with higher PVAc grafting content
compatibilizer showed better properties than that of lower PVAc
grafting content compatibilizer. The amount of compatibilizer was
found optimized in the range of 0.5-1.0 Wt% depending on the mol%
PVAc.
Abstract: Polarization modulation infrared reflection absorption
spectroscopy (PM-IRRAS) in combination with electrochemistry,
was employed to study the influence of surface charge (potential) on
the kinetics of bovine serum albumin (BSA) adsorption on a
biomedical-grade 316LVM stainless steel surface is discussed. The
BSA adsorption kinetics was found to greatly depend on the surface
potential. With an increase in surface potential towards more
negative values, both the BSA initial adsorption rate and the
equilibrium (saturated) surface concentration also increased. Both
effects were explained on the basis of replacement of well-ordered
water molecules at the 316LVM / solution interface, i.e. by the
increase in entropy of the system.
Abstract: This paper proposes, implements and evaluates an original discretization method for continuous random variables, in order to estimate the reliability of systems for which stress and strength are defined as complex functions, and whose reliability is not derivable through analytic techniques. This method is compared to other two discretizing approaches appeared in literature, also through a comparative study involving four engineering applications. The results show that the proposal is very efficient in terms of closeness of the estimates to the true (simulated) reliability. In the study we analyzed both a normal and a non-normal distribution for the random variables: this method is theoretically suitable for each parametric family.
Abstract: In the competitive environment of aircraft industries it becomes absolutely necessary to improve the efficiency, performance of the aircrafts to reduce the development and operating costs considerably, in order to capitalize the market. An important contribution to improve the efficiency and performance can be
achieved by decreasing the aircraft weight through considerable
usage of composite materials in primary aircraft structures. In this study, a type of composite material called Carbon Fiber Reinforced
Plastic (CFRP) is explored for the usage is aircraft skin panels. Even
though there were plenty of studies and research has been already
carried out, here a practical example of an aircraft skin panel is taken
and substantiated the benefits of composites material usage over the
metallic skin panel. A crown skin panel of a commercial aircraft is
designed using both metal and composite materials. Stress analysis
has been carried out for both and margin of safety is estimated for the
critical load cases. The skin panels are compared for manufacturing,
tooling, assembly and cost parameters. Detail step by step comparison between metal and composite constructions are studied
and results are tabulated for better understanding.
Abstract: Cyclic delay diversity (CDD) is a simple technique to
intentionally increase frequency selectivity of channels for orthogonal
frequency division multiplexing (OFDM).This paper proposes a residual
carrier frequency offset (RFO) estimation scheme for OFDMbased
broadcasting system using CDD. In order to improve the RFO
estimation, this paper addresses a decision scheme of the amount of
cyclic delay and pilot pattern used to estimate the RFO. By computer
simulation, the proposed estimator is shown to benefit form propoerly
chosen delay parameter and perform robustly.