Abstract: Although silicon photonic devices provide a significantly larger bandwidth and dissipate a substantially less power than the electronic devices, they suffer from a large size due to the fundamental diffraction limit and the weak optical response of Si. A potential solution is to exploit Si plasmonics, which may not only miniaturize the photonic device far beyond the diffraction limit, but also enhance the optical response in Si due to the electromagnetic field confinement. In this paper, we discuss and summarize the recently developed metal-insulator-Si-insulator-metal nanoplasmonic waveguide as well as various passive and active plasmonic components based on this waveguide, including coupler, bend, power splitter, ring resonator, MZI, modulator, detector, etc. All these plasmonic components are CMOS compatible and could be integrated with electronic and conventional dielectric photonic devices on the same SOI chip. More potential plasmonic devices as well as plasmonic nanocircuits with complex functionalities are also addressed.
Abstract: Introducing Electromagnetic Interference and Electromagnetic Compatibility, or “The Art of Black Magic", for engineering students might be a terrifying experience both for students and tutors. Removing the obstacle of large, expensive facilities like a fully fitted EMC laboratory and hours of complex theory, this paper demonstrates a design of a laboratory setup for student exercises, giving students experience in the basics of EMC/EMI problems that may challenge the functionality and stability of embedded system designs. This is done using a simple laboratory installation and basic measurement equipment such as a medium cost digital storage oscilloscope, at the cost of not knowing the exact magnitude of the noise components, but rather if the noise is significant or not, as well as the source of the noise. A group of students have performed a trial exercise with good results and feedback.
Abstract: One of Effective parameters on the performance of linear induction motors is number of poles which must be selected and optimized to increase power efficiency and motor performance significantly. In this paper a double-sided linear induction motor with different poles number by using MAXWELL3D software is designed and with finite element method is analyzed electromagnetically. Then for dynamic simulation, linear motor by using MATLAB software is simulated. The results show that by adding poles number, system time response is increased and motor after more time reaches to steady state. Also propulsion force of motor is increased.
Abstract: In determining the electromagnetic properties of
magnetic materials, hysteresis modeling is of high importance. Many
models are available to investigate those characteristics but they tend
to be complex and difficult to implement. In this paper a new
qualitative hysteresis model for ferromagnetic core is presented,
based on the function approximation capabilities of adaptive neuro
fuzzy inference system (ANFIS). The proposed ANFIS model
combined the neural network adaptive capabilities and the fuzzy
logic qualitative approach can restored the hysteresis curve with a
little RMS error. The model accuracy is good and can be easily
adapted to the requirements of the application by extending or
reducing the network training set and thus the required amount of
measurement data.
Abstract: A study of electromagnetic flow meter is presented in the paper. Comparison has been made between the analytical and the numerical results by the use of FEM numerical analysis (Quick Field 5.6) for determining polarization voltage through the circle cross section of the polarization transducer. Exciting and geometrical parameters increasing its effectiveness has been examined. The aim is to obtain maximal output signal. The investigations include different variants of the magnetic flux density distribution around the tube: homogeneous field of magnitude Bm, linear distribution with maximal value Bm and trapezium distribution conserving the same exciting magnetic energy as the homogeneous field.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: This paper presents an approach which is based on the
use of supervised feed forward neural network, namely multilayer
perceptron (MLP) neural network and finite element method (FEM)
to solve the inverse problem of parameters identification. The
approach is used to identify unknown parameters of ferromagnetic
materials. The methodology used in this study consists in the
simulation of a large number of parameters in a material under test,
using the finite element method (FEM). Both variations in relative
magnetic permeability and electrical conductivity of the material
under test are considered. Then, the obtained results are used to
generate a set of vectors for the training of MLP neural network.
Finally, the obtained neural network is used to evaluate a group of
new materials, simulated by the FEM, but not belonging to the
original dataset. Noisy data, added to the probe measurements is used
to enhance the robustness of the method. The reached results
demonstrate the efficiency of the proposed approach, and encourage
future works on this subject.
Abstract: The scalar wave equation for a potential in a curved space time, i.e., the Laplace-Beltrami equation has been studied in this work. An action principle is used to derive a finite element algorithm for determining the modes of propagation inside a waveguide of arbitrary shape. Generalizing this idea, the Maxwell theory in a curved space time determines a set of linear partial differential equations for the four electromagnetic potentials given by the metric of space-time. Similar to the Einstein-s formulation of the field equations of gravitation, these equations are also derived from an action principle. In this paper, the expressions for the action functional of the electromagnetic field have been derived in the presence of gravitational field.
Abstract: The finite-difference time-domain (FDTD) method is
one of the most widely used computational methods in
electromagnetic. This paper describes the design of two-dimensional
(2D) FDTD simulation software for transverse magnetic (TM)
polarization using Berenger's split-field perfectly matched layer
(PML) formulation. The software is developed using Matlab
programming language. Numerical examples validate the software.
Abstract: This paper presents the study of hardness profile of spur gear heated by induction heating process in function of the machine parameters, such as the power (kW), the heating time (s) and the generator frequency (kHz). The global work is realized by 3D finite-element simulation applied to the process by coupling and resolving the electromagnetic field and the heat transfer problems, and it was performed in three distinguished steps. First, a Comsol 3D model was built using an adequate formulation and taking into account the material properties and the machine parameters. Second, the convergence study was conducted to optimize the mesh. Then, the surface temperatures and the case depths were deeply analyzed in function of the initial current density and the heating time in medium frequency (MF) and high frequency (HF) heating modes and the edge effect were studied. Finally, the simulations results are validated using experimental tests.
Abstract: This paper presents the optimum design for a double
stator, cup rotor machine; a novel type of BLDC PM Machine. The optimization approach is divided into two stages: the first stage is
calculating the machine configuration using Matlab, and the second stage is the optimization of the machine using Finite Element
Modeling (FEM). Under the design specifications, the machine
model will be selected from three pole numbers, namely, 8, 10 and 12 with an appropriate slot number. A double stator brushless DC
permanent magnet machine is designed to achieve low cogging torque; high electromagnetic torque and low ripple torque.
Abstract: In order to realize long-lived electric propulsion
systems, we have been investigating an electrodeless plasma thruster.
In our concept, a helicon plasma is accelerated by the magnetic nozzle
for the thrusts production. In addition, the electromagnetic thrust can
be enhanced by the additional radio-frequency rotating electric field
(REF) power in the magnetic nozzle. In this study, a direct
measurement of the electromagnetic thrust and a probe measurement
have been conducted using a laboratory model of the thruster under the
condition without the REF power input. Fromthrust measurement, it is
shown that the thruster produces a sub-milli-newton order
electromagnetic thrust force without the additional REF power. The
thrust force and the density jump are observed due to the discharge
mode transition from the inductive coupled plasma to the helicon wave
excited plasma. The thermal thrust is theoretically estimated, and the
total thrust force, which is a sum of the electromagnetic and the
thermal thrust force and specific impulse are calculated to be up to 650
μN (plasma production power of 400 W, Ar gas mass flow rate of 1.0
mg/s) and 210 s (plasma production power of 400 W, Ar gas mass flow
rate of 0.2 mg/s), respectively.
Abstract: In working mode some unexpected changes could
be arise in inner structure of electromagnetic device. They
influence modification in electromagnetic field propagation map.
The field values at an observed boundary are also changed. The
development of the process has to be watched because the arising
structural changes would provoke the device to be gone out later.
The probabilistic assessment of the state is possible to be made.
The numerical assessment points if the resulting changes have
only accidental character or they are due to the essential inner
structural disturbances.
The presented application example is referring to the 200MW
turbine-generator. A part of the stator core end teeth zone is
simulated broken. Quasi three-dimensional electromagnetic and
temperature field are solved applying FEM. The stator core state
diagnosis is proposed to be solved as an identification problem on
the basis of a statistical criterion.
Abstract: Today with the rapid growth of telecommunications equipment, electronic and developing more and more networks of power, influence of electromagnetic waves on one another has become hot topic discussions. So in this article, this issue and appropriate mechanisms for EMC operations have been presented. First, impact of high voltage lines on the surrounding environment especially on the control room has been investigated, then to reduce electromagnetic radiation, various methods of shielding are provided and shielding effectiveness of them has been compared. It should be expressed that simulations have been done by the finite element method (FEM).
Abstract: With the advance in wireless networking, IEEE 802.16 WiMAX technology has been widely deployed for several applications such as “last mile" broadband service, cellular backhaul, and high-speed enterprise connectivity. As a result, military employed WiMAX as a high-speed wireless connection for data-link because of its point to multi-point and non-line-of-sight (NLOS) capability for many years. However, the risk of using WiMAX is a critical factor in some sensitive area of military applications especially in ammunition manufacturing such as solid propellant rocket production. The US DoD policy states that the following certification requirements are met for WiMAX: electromagnetic effects on the environment (E3) and Hazards of Electromagnetic Radiation to Ordnance (HERO). This paper discuses the Recommended Power Densities and Safe Separation Distance (SSD) for HERO on WiMAX systems deployed on solid propellant rocket production. The result of this research found that WiMAX is safe to operate at close proximity distances to the rocket production based on AF Guidance Memorandum immediately changing AFMAN 91-201.
Abstract: A transient finite element model has been developed
to study the heat transfer and fluid flow during spot Gas Tungsten
Arc Welding (GTAW) on stainless steel. Temperature field, fluid
velocity and electromagnetic fields are computed inside the cathode,
arc-plasma and anode using a unified MHD formulation. The
developed model is then used to study the influence of different
helium-argon gas mixtures on both the energy transferred to the
workpiece and the time evolution of the weld pool dimensions. It is
found that the addition of helium to argon increases the heat flux
density on the weld axis by a factor that can reach 6.5. This induces
an increase in the weld pool depth by a factor of 3. It is also found
that the addition of only 10% of argon to helium decreases
considerably the weld pool depth, which is due to the electrical
conductivity of the mixture that increases significantly when argon is
added to helium.
Abstract: Dielectric sheet perturbation to the dominant TE111
mode resonant frequency of a circular cavity is studied and presented
in this paper. The dielectric sheet, placed at the middle of the airfilled
cavity, introduces discontinuities and disturbs the configuration
of electromagnetic fields in the cavity. For fixed dimensions of cavity
and fixed thickness of the loading dielectric, the dominant resonant
frequency varies quite linearly with the permittivity of the dielectric.
This quasi-linear relationship is plotted using Maple software and
verified using 3D electromagnetic simulations. Two probes are used
in the simulation for wave excitation into and from the cavity. The
best length of probe is found to be 3 mm, giving the closest resonant
frequency to the one calculated using Maple. A total of fourteen
different dielectrics of permittivity ranging from 1 to 12.9 are tested
one by one in the simulation. The works show very close agreement
between the results from Maple and the simulation. A constant
difference of 0.04 GHz is found between the resonant frequencies
collected during simulation and the ones from Maple. The success of
this project may lead to the possibility of using the middle loaded
cavity at TE111 mode as a microwave non-destructive testing of solid
materials.
Abstract: Fuzzy logic system (FLS) is used in this study to
predict the tractive performance in terms of traction force, and
motion resistance for an intelligent air cushion track vehicle while it
operates in the swamp peat. The system is effective to control the
intelligent air –cushion system with measuring the vehicle traction
force (TF), motion resistance (MR), cushion clearance height (CH)
and cushion pressure (CP). Ultrasonic displacement sensor, pull-in
solenoid electromagnetic switch, pressure control sensor, micro
controller, and battery pH sensor are incorporated with the Fuzzy
logic system to investigate experimentally the TF, MR, CH, and CP.
In this study, a comparison for tractive performance of an intelligent
air cushion track vehicle has been performed with the results obtained
from the predicted values of FLS and experimental actual values. The
mean relative error of actual and predicted values from the FLS
model on traction force, and total motion resistance are found as 5.58
%, and 6.78 % respectively. For all parameters, the relative error of
predicted values are found to be less than the acceptable limits. The
goodness of fit of the prediction values from the FLS model on TF,
and MR are found as 0.90, and 0.98 respectively.
Abstract: The analysis of electromagnetic environment using
deterministic mathematical models is characterized by the
impossibility of analyzing a large number of interacting network
stations with a priori unknown parameters, and this is characteristic,
for example, of mobile wireless communication networks. One of the
tasks of the tools used in designing, planning and optimization of
mobile wireless network is to carry out simulation of electromagnetic
environment based on mathematical modelling methods, including
computer experiment, and to estimate its effect on radio
communication devices. This paper proposes the development of a
statistical model of electromagnetic environment of a mobile
wireless communication network by describing the parameters and
factors affecting it including the propagation channel and their
statistical models.
Abstract: The present study is concerned with the absorption
center of photophoresis within a micro-sized and spheroidal particle in
a gaseous medium. A particle subjected to an intense light beam can
absorb electromagnetic energy within the particle unevenly, which
results in photophoretic force to drive the particle in motion. By
evaluating the energy distribution systematically at various conditions,
the study focuses on the effects of governing parameters, such as
particle aspect ratio, size parameter, refractivity, and absorptivity, on
the heat source function within the particle and their potential
influences to the photophoresis.