Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: This paper presents a cold chain monitoring system which focuses on assessment of quality and dynamic pricing information about food in cold chain. Cold chain is composed of many actors and stages; however it can be seen as a single entity since a breakdown in temperature control at any stage can impact the final quality of the product. In a cold chain, the shelf life, quality, and safety of perishable food throughout the supply chain is greatly impacted by environmental factors especially temperature. In this paper, a prototype application is implemented to retrieve timetemperature history, the current quality and the dynamic price setting according to changing quality impacted by temperature fluctuations in real-time.
Abstract: Since atmosphere pressure field is an actual envoy of
climatic signal the atmospheric Highs and Lows should be attributed
to the key active focal points within the ocean-atmosphere interplay
system. Here we were set a task to determine how the dynamics of
those centres of action relates to the climate change both on regional
and global scales. For this target the near-surface temperature and
atmospheric pressure differences between the Icelandic Low and the
Azores High were considered. The secular term of phase states of the
system under consideration was found divided into three
nonintersecting subsets. Each of that was put in consequence with
one of three climatic scenarios related to the periods of 1905-1935
(relatively warm phase), 1940-1970 (cold phase) and 1980-2000
(warm phase).
Abstract: This paper studied the synthesis of monoacylglycerol (monolaurin) by glycerolysis of coconut oil and crude glycerol, catalyzed by Carica papaya lipase. Coconut oil obtained from cold pressed extraction method and crude glycerol obtained from the biodiesel plant in Department of Chemistry, Uttaradit Rajabhat University, Thailand which used oils were used as raw materials for biodiesel production through transesterification process catalyzed by sodium hydroxide. The influences of the following variables were studied: (i) type of organic solvent, (ii) molar ratio of substrate, (iii) reaction temperature, (iv) reaction time, (v) lipase dosage, and (vi) initial water activity of enzyme. High yields in monoacylglycerol (58.35%) were obtained with molar ratio of glycerol to oil at 8:1 in ethanol, temperature was controlled at 45oC for 36 hours, the amount of enzyme used was 20 wt% of oil and initial water activity of enzyme at 0.53.
Abstract: The main emphasis of metallurgists has been to process the materials to obtain the balanced mechanical properties for the given application. One of the processing routes to alter the properties is heat treatment. Nearly 90% of the structural applications are related to the medium carbon an alloyed steels and hence are regarded as structural steels. The major requirement in the conventional steel is to improve workability, toughness, hardness and grain refinement. In this view, it is proposed to study the mechanical and tribological properties of unalloyed structural (AISI 1140) steel with different thermal (heat) treatments like annealing, normalizing, tempering and hardening and compared with as brought (cold worked) specimen. All heat treatments are carried out in atmospheric condition. Hardening treatment improves hardness of the material, a marginal decrease in hardness value with improved ductility is observed in tempering. Annealing and normalizing improve ductility of the specimen. Normalized specimen shows ultimate ductility. Hardened specimen shows highest wear resistance in the initial period of slide wear where as above 25KM of sliding distance, as brought steel dominates the hardened specimen. Both mild and severe wear regions are observed. Microstructural analysis shows the existence of pearlitic structure in normalized specimen, lath martensitic structure in hardened, pearlitic, ferritic structure in annealed specimen.
Abstract: In this paper, the energy performance of a selected
UHDE Ammonia plant is optimized by conducting heat integration through waste heat recovery and the synthesis of a heat exchange
network (HEN). Minimum hot and cold utility requirements were estimated through IChemE spreadsheet. Supporting simulation was
carried out using HYSYS software. The results showed that there is
no need for heating utility while the required cold utility was found to
be around 268,714 kW. Hence a threshold pinch case was faced. Then, the hot and cold streams were matched appropriately. Also,
waste heat recovered resulted with savings in HP and LP steams of
approximately 51.0% and 99.6%, respectively. An economic analysis
on proposed HEN showed very attractive overall payback period not
exceeding 3 years. In general, a net saving approaching 35% was
achieved in implementing heat optimization of current studied UHDE Ammonia process.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: Human always tried to create a suitable situation for their life according to environmental conditions. In fact, geography has an important role in the shape of our living area. Iran also as a four-season country has different climate type: hot and humid, hot and dry, mid and humid, and cold; therefore, we can find different architecture styles in Iran. Gilan-s traditional architecture is a suitable sample of sustainable construction in Iran. Because the main factors of every dwelling are the climatic, social, economic and cultural effects which demonstrate the interaction between environment and people settlement. This paper was determined the interaction between environmental factors and the rural dwellings in the Gilan province. Also, traditional village (city) of Masouleh as a rare sample of rural and sustainable architecture was introduced.
Abstract: The oleaginous yeasts Lipomyces starkey were grown
in the presence of dairy industry wastewaters (DIW). The yeasts were
able to degrade the organic components of DIW and to produce a
significant fraction of their biomass as triglycerides.
When using DIW from the Ricotta cheese production or residual
whey as growth medium, the L. starkey could be cultured without
dilution nor external organic supplement. On the contrary, the yeasts
could only partially degrade the DIW from the Mozzarella cheese
production, due to the accumulation of a metabolic product beyond
the threshold of toxicity. In this case, a dilution of the DIW was
required to obtain a more efficient degradation of the carbon
compounds and an higher yield in oleaginous biomass.
The fatty acid distribution of the microbial oils obtained showed a
prevalence of oleic acid, and is compatible with the production of a II
generation biodiesel offering a good resistance to oxidation as well as
an excellent cold-performance.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.
Abstract: Today Environmental Impact Assessment (EIA) is known as one of the most important tools for decision makers in the construction of civil and industrial projects towards sustainable development. In the past, projects were evaluated based on cost and benefit analysis regardless of the physical and biological environmental effects and its socio-economical impacts. According to the Department of Environment (DOE) of Iran's regulations, the construction of hydroelectric dams is an activity that requires an EIA report. In this paper the environmental impact assessment of the Gotvand hydro-electrical dam has been evaluated in the three environment elements, biological, Physical-chemical and cultural units. This dam is one of the largest dams in Iran with a volume of 4500 MCM and is going to be the last dam on the Karoon River in the south of Iran. In this paper the ICOLD (International Commission on Large Dams) technique was employed for the environmental impact assessment of the dam. The research includes all socio economical and environmental effects of the dam during the construction and operation of the hydro electric dam and Environmental management, monitoring and mitigation of negative impacts were analyzed. In this project the results led to using some techniques to protect the destructive impacts on biological aspects beside the effective long time period impacts on the biological aspects. The impacts on physical aspects are temporary and negative commonly that could be restored and rehabilitated in natural process in the long time in operation period.
Abstract: An influence of intranasal combined injection of live
cold-adapted influenza vaccine with chitosan derivatives as adjuvants
on the subpopulation structure of mononuclear leukocytes of mouse
spleen which reflects the orientation of the immune response was
studied. It is found that the inclusion of chitosan preparations
promotes activation of cellular-level of immune response.
Abstract: Stairway Ushtobin Village is one of the five villages with original and sustainable architecture in Northwest of Iran along the border of Armenia, which has been able to maintain its environment and sustainable ecosystem. Studying circulation, function and scale (grand, medium and minor) of space, ratio of full and empty spaces, number and height of stairs, ratio of compound volume to luxury spaces, openings, type of local masonry (stone, mud, wood) and form of covering elements have been carried out in four houses of this village comparatively as some samples in this article, and furthermore, this article analyzes that the architectural shapes and organic texture of the village meet the needs of cold and dry climate. Finally, some efficient plans are offered suiting the present needs of the village to have a sustainable architecture.
Abstract: KSLV-I(Korea Space Launch Vehicle-I) is designed as
a launch vehicle to enter a 100 kg-class satellite to the LEO(Low Earth
Orbit). Attitude angles of the upper-stage, including roll, pitch and
yaw are controlled by the cold gas thruster system using nitrogen gas.
The cold gas thruster is an actuator in the RCS(Reaction Control
System). To design an attitude controller for the upper-stage, thrust
measurement in vacuum condition is required. In this paper, the new
thrust measurement system and calibration mechanism are developed
and measurement errors and signal processing method are presented.
Abstract: In this article, using finite element analysis (FEA)
and an X-ray diffractometer (XRD), cold-sprayed titanium particles
on a steel substrate is investigated in term of cooling time and the
development of residual strains. Three cooling-down models of
sprayed particles after deposition stage are simulated and discussed:
the first model (m1) considers conduction effect to the substrate only,
the second model (m2) considers both conduction as well as
convection effect to the environment, and the third model (m3) which
is the same as the second model but with the substrate heated to a
near particle temperature before spraying. Thereafter, residual strains
developed in the third model is compared with the experimental
measurement of residual strains, which involved a Bruker D8
Advance Diffractometer using CuKa radiation (40kV, 40mA)
monochromatised with a graphite sample monochromator. For
deposition conditions of this study, a good correlation was found to
exist between the FEA results and XRD measurements of residual
strains.
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: A judicious choice of insert material, tool geometry and
cutting conditions can make hard turning produce better surfaces than
grinding. In the present study, an attempt has been made to
investigate the effect of cutting tool materials on cutting forces (feed
force, thrust force and cutting force) in finish hard turning of AISI
D2 cold work tool steel. In conclusion of the results obtained with a
constant depth of cut and feed rate, it is important to note that cutting
force is directly affected by cutting tool material.
Abstract: This paper presented a novel combined cycle of air separation and natural gas liquefaction. The idea is that natural gas can be liquefied, meanwhile gaseous or liquid nitrogen and oxygen are produced in one combined cryogenic system. Cycle simulation and exergy analysis were performed to evaluate the process and thereby reveal the influence of the crucial parameter, i.e., flow rate ratio through two stages expanders β on heat transfer temperature difference, its distribution and consequent exergy loss. Composite curves for the combined hot streams (feeding natural gas and recycled nitrogen) and the cold stream showed the degree of optimization available in this process if appropriate β was designed. The results indicated that increasing β reduces temperature difference and exergy loss in heat exchange process. However, the maximum limit value of β should be confined in terms of minimum temperature difference proposed in heat exchanger design standard and heat exchanger size. The optimal βopt under different operation conditions corresponding to the required minimum temperature differences was investigated.
Abstract: The great majority of the electric installations belong
to the first and second category. In order to ensure a high level of
reliability of their electric system feeder, two power supply sources
are envisaged, one principal, the other of reserve, generally a cold
reserve (electric diesel group).
The principal source being under operation, its control can be ideal
and sure, however for the reserve source being in stop, a preventive
maintenance-s which proceeds on time intervals (periodicity) and
for well defined lengths of time are envisaged, so that this source will
always available in case of the principal source failure.
The choice of the periodicity of preventive maintenance of the
source of reserve influences directly the reliability of the electric
feeder system. On the basis of the semi-markovians processes, the
influence of the periodicity of the preventive maintenance of the
source of reserve is studied and is given the optimal periodicity.