Abstract: Field experiment was conducted to investigate the combine use of animal manure and inorganic fertilizer on growth and yield performance of vegetable cowpea. The experiment was laid out in a Randomized Complete Block Design (RCBD) with seven treatments. Poultry manure, cattle manure and goat manure were evaluated with recommended level of inorganic fertilizer for vegetable cowpea. The highest crop yield was obtained by the application of poultry manure combined with the recommended level of inorganic fertilizer. The lowest yield was obtained by the application of goat manure only. In addition, the results revealed that the goat manure and cattle manure were inferior to poultry manure as a source of organic manure for vegetable cowpea cultivation. The animal manure combine with chemical fertilizer gave a higher yield when compared to the sole application of animal manure. The soil analysis showed that the nitrogen content and phosphorus content of poultry manure treated plots were higher than other treatments tested. But potassium content was higher in goat manure treated plots. The results further revealed that the poultry manure has a beneficial effect on crop growth and yield compared with other treatments. Therefore, the combined use of poultry manure with inorganic fertilizer application has been recognized as the most suitable way of ensuring high crop yield.
Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: This paper analyses the torsional efforts in gas turbine-generator shafts caused by high speed automatic reclosing of transmission lines. This issue is especially important for cases of three phase short circuit and unsuccessful reclosure of lines in the vicinity of the thermal plant. The analysis was carried out for the thermal plant TERMOPERNAMBUCO located on Northeast region of Brazil. It is shown that stress level caused by lines unsuccessful reclosing can be several times higher than terminal three-phase short circuit. Simulations were carried out with detailed shaft torsional model provided by machine manufacturer and with the “Alternative Transient Program – ATP" program [1]. Unsuccessful three phase reclosing for selected lines in the area closed to the plant indicated most critical cases. Also, reclosing first the terminal next to the gas turbine gererator will lead also to the most critical condition. Considering that the values of transient torques are very sensible to the instant of reclosing, simulation of unsuccessful reclosing with statistics ATP switch were carried out for determination of most critical transient torques for each section of the generator turbine shaft.
Abstract: This paper develops a critical perspective on using
culture and creativity as tools for urban regeneration. Following a
brief assessment of the evolution of cultural policy in recent decades
and different urban regeneration scheme, the concepts of creativity
and creative cities are discussed. This is followed by an attempt to
clarify the relationship between the concepts of creativity and culture.
A more detailed critique of cultural and creative initiatives in Serbian
cities is then undertaken. These attempts show that the potential for
development of urban regeneration driven by culture and creativity
exist. But, these initiatives failed to produce adequate results because
they did not take root as a comprehensive urban regeneration
strategy, therefore, recommendations for further development are
offered.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: The link between urban planning and design principles and the built environment of an urban renewal area is of interest to the field of urban studies. During the past decade, there has also been increasing interest in urban planning and design; this interest is motivated by the possibility that design policies associated with the built environment can be used to control, manage, and shape individual activity and behavior. However, direct assessments and design techniques of the links between how urban planning design policies influence individuals are still rare in the field. Recent research efforts in urban design have focused on the idea that land use and design policies can be used to increase the quality of design projects for an urban renewal area-s built environment. The development of appropriate design techniques for the built environment is an essential element of this research. Quality function deployment (QFD) is a powerful tool for improving alternative urban design and quality for urban renewal areas, and for procuring a citizen-driven quality system. In this research, we propose an integrated framework based on QFD and an Analytic Network Process (ANP) approach to determine the Alternative Technical Requirements (ATRs) to be considered in designing an urban renewal planning and design alternative. We also identify the research designs and methodologies that can be used to evaluate the performance of urban built environment projects. An application in an urban renewal built environment planning and design project evaluation is presented to illustrate the proposed framework.
Abstract: The objective was to determine the single gene and
interaction effect of composite genotype of beta-kappa casein and
DGAT1 gene on milk yield (MY) and milk composition, content of
milk fat (%FAT), milk protein (%PRO), solid not fat (%SNF), and
total solid (%TS) in crossbred Holstein cows. Two hundred and
thirty- one cows were genotyped with PCR-RFLP for DGAT1 and
composite genotype data of beta-kappa casein from previous work
were used. Two model, (1), and (2), was used to estimate single gene
effect, and interaction effect on the traits, respectively. The
significance of interaction effects on all traits were detected. Most
traits have consistent pattern of significant when model (1), and (2)
were compared, except the effect of composite genotype of betakappa
casein on %FAT, and the effect of DGAT1 on MY, which the
significant difference was detected in only model (1).The results
suggested that when the optimum of all traits was necessary,
interaction effect should be concerned.
Abstract: The adoption of building information modeling (BIM)
is increasing in the construction industry. However, quantity
surveyors are slow in adoption compared to other professions due to
lack of awareness of the BIM’s potential in their profession. It is still
unclear on how BIM application can enhance quantity surveyors’
work performance and project performance. The aim of this research
is to identify the capabilities of BIM in quantity surveying practices
and examine the relationship between BIM capabilities and project
performance. Questionnaire survey and interviews were adopted for
data collection. Literature reviews identified there are eleven BIM
capabilities in quantity surveying practice. Questionnaire results
showed that there are several BIM capabilities significantly
correlated with project performance in time, cost and quality aspects
and the results were validated through interviews. These findings
show that BIM has the capabilities to enhance quantity surveyors’
performances and subsequently improved project performance.
Abstract: Knowledge management is a critical component of
competitive success in service organizations. Knowledge
management centers on creating new knowledge and utilizing
existing knowledge. While utilizing existing knowledge relates to
input and control and can lead to a reduction in costs; creating new
knowledge relates to output and growth and can lead to an increase in
revenue. Therefore managers must ensure that they can successfully
optimize the knowledge and talent in their organizations. To do this
they and must try to develop an environment that promotes the
generation, acquisition, transfer and use of valuable knowledge in
creative ways. However knowledge management is complex and
diverse. Research suggests that organizations in general and SMEs in
particular are finding it difficult to implement successful knowledge
management initiatives. Our research attempts to understand whether
organizations are adopting best practice initiatives in their
organizations. This paper presents findings from an exploratory study
of 139 SMEs operating in the tourism sector across Europe. The
goals of the survey is to assess the level of awareness of knowledge
and talent management strategies and methodologies and to
determine whether the responding companies implement best practice
knowledge management initiatives in their organizations Analysis of
the findings from the study are presented and discussed.
Abstract: Heuristics-based search methodologies normally
work on searching a problem space of possible solutions toward
finding a “satisfactory" solution based on “hints" estimated from the
problem-specific knowledge. Research communities use different
types of methodologies. Unfortunately, most of the times, these hints
are immature and can lead toward hindering these methodologies by
a premature convergence. This is due to a decrease of diversity in
search space that leads to a total implosion and ultimately fitness
stagnation of the population. In this paper, a novel Decision Maturity
framework (DMF) is introduced as a solution to this problem. The
framework simply improves the decision on the direction of the
search by materializing hints enough before using them. Ideas from
this framework are injected into the particle swarm optimization
methodology. Results were obtained under both static and dynamic
environment. The results show that decision maturity prevents
premature converges to a high degree.
Abstract: In this research, the laminar heat transfer of natural convection on vertical surfaces has been investigated. Most of the studies on natural convection have been considered constantly whereas velocity and temperature domain, do not change with time, transient one are used a lot. Governing equations are solved using a finite volume approach. The convective terms are discretized using the power-law scheme, whereas for diffusive terms the central difference is employed. Coupling between the velocity and pressure is made with SIMPLE algorithm. The resultant system of discretized linear algebraic equations is solved with an alternating direction implicit scheme. Then a configuration of rectangular fins is put in different ways on the surface and heat transfer of natural convection on these surfaces without sliding is studied and finally optimization is done.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: Composite steel shear wall is a lateral load resisting system which consists of a steel plate with concrete wall attached to one or both sides to prevent it from elastic buckling. The composite behavior is ensured by utilizing high-strength bolts. This paper investigates the effect of distance between bolts, and for this purpose 14 one-story one-bay specimens with various bolts spacing were modeled by finite element code which is developed by the authors. To verify the model, numerical results were compared with a valid experiment which illustrate proper agreement. Results depict increasing the distance between bolts would improve the seismic ever, this increase must be limited, because of large distances will cause widespread buckling of the steel plate in free subpanels between bolts and would result in no improvement. By comparing the results in elastic region, it was observed initial stiffness is not affected by changing the distance.
Abstract: In this paper, the thermo-electro-structural coupledfield
in a cracked metal plate is studied using the finite element
analysis. From the computational results, the compressive stresses
reveal near the crack tip. This conclusion agrees with the past
reference. Furthermore, the compressive condition can retard and stop
the crack growth during the Joule heating process.
Abstract: As one result of the project “Reactive Construction
Project Scheduling using Real Time Construction Logistic Data and
Simulation”, a procedure for using data about uncertain resource
availability assumptions in reactive scheduling processes has been
developed. Prediction data about resource availability is generated in
a formalized way using real-time monitoring data e.g. from auto-ID
systems on the construction site and in the supply chains. The paper
focusses on the formalization of the procedure for monitoring
construction logistic processes, for the detection of disturbance and
for generating of new and uncertain scheduling assumptions for the
reactive resource constrained simulation procedure that is and will be
further described in other papers.
Abstract: According to historical legend, after the revelation of the holy Qur'an, which gave the hijab compulsory and women were required to cover the head and body with a handkerchief, and the general form of clothing in her veil, Muslim women have begun to comply with this worthy tradition. This article discusses the history of the rise and spread of the hijab and its types. And here is described in detail types of hijab and its intended value, style hijab in different regions. Now wearing the hijab, hijab in general the problem is important not only in the Arab world, but also in the world.
Abstract: This paper presents a comparative study on
Vanadyl Phthalocyanine (VOPc) thin films deposited by thermal
evaporation and spin coating techniques. The samples
were prepared on cleaned glass substrates and annealed at
various temperatures ranging form 95oC to 155oC. To obtain
the morphological and structural properties of VOPc thin
films, X-ray diffraction (XRD) technique and atomic force
microscopy (AFM) have been implied. The AFM topographic
images show a very slight difference in the thermally grown
films, before and after annealing, however best results are
achieved for the spin-cast film annealed at 125oC. The XRD
spectra show no existence of the sharp peaks, suggesting the
material to be amorphous. The humps in the XRD patterns
indicate the presence of some crystallites.
Abstract: The temperature distribution and the heat transfer
rates through a multi-layer door of a furnace were investigated. The
inside of the door was in contact with hot air and the other side of the
door was in contact with room air. Radiation heat transfer from the
walls of the furnace to the door and the door to the surrounding area
was included in the problem. This work is a two dimensional steady
state problem. The Churchill and Chu correlation was used to find
local convection heat transfer coefficients at the surfaces of the
furnace door. The thermophysical properties of air were the functions
of the temperatures. Polynomial curve fitting for the fluid properties
were carried out. Finite difference method was used to discretize for
conduction heat transfer within the furnace door. The Gauss-Seidel
Iteration was employed to compute the temperature distribution in
the door.
The temperature distribution in the horizontal mid plane of the
furnace door in a two dimensional problem agrees with the one
dimensional problem. The local convection heat transfer coefficients
at the inside and outside surfaces of the furnace door are exhibited.
Abstract: A finite element analysis was conducted to determine
the effect of moisture diffusion and hygroscopic swelling in rice. A
parallel simple stochastic modeling was performed to predict the
number of grains cracked as a result of moisture absorption and
hygroscopic swelling. Rice grains were soaked in thermally (25 oC)
controlled water and then tested for compressive stress. The
destructive compressive stress tests revealed through compressive
stress calculation that the peak force required to cause cracking in
grains soaked in water reduced with time as soaking duration was
extended. Results of the experiment showed that several grains had
their value of the predicted compressive stress below the von Mises
stress and were interpreted as grains which become cracked and/or
broke during soaking. The technique developed in this experiment
will facilitate the approximation of the number of grains which will
crack during soaking.