Abstract: The range of the output power is a very important and evident limitation of two-level inverters. In order to overcome this disadvantage, multilevel inverters are introduced. Recently, Cascade H-Bridge inverters have emerged as one of the popular converter topologies used in numerous industrial applications. The modulation switching strategies such as phase shifted carrier based Pulse Width Modulation (PWM) technique and Stair case modulation with Selective Harmonic Elimination (SHE) PWM technique are generally used. NR method is used to solve highly non linear transcendental equations which are formed by SHEPWM method. Generally NR method has a drawback of requiring good initial guess but in this paper a new approach is implemented for NR method with any random initial guess. A three phase CHB 11-level inverter is chosen for analysis. MATLAB/SIMULINK programming environment and harmonic profiles are compared. Finally this paper presents a method at fundamental switching frequency with least % THDV.
Abstract: In the paper the research of flat textile products for use
as electrodes was presented. Material-s resistance measurements were
carried out to determine the suitability of the textiles. Based on the received results of studies different types of textile electrodes were
designed. Textile electrodes tests were carried out on human
phantoms. The electro-conductive properties of human forearm
phantom were also described. Based on this results special electroconductive
hydrogels with electro-conductive particles were feasible. The hydrogel is an important element of the forearm-s phantom
model of a survey of electrodes for muscle electrostimulation. The
hydrogel is an equivalent human skin and tissue. The hydrogel should
have a permanence and recurrence of the electro-conductive properties.
Abstract: A power cable is widely used for power supply in
power distributing networks and power transmission lines. Due to
limitations in the production, delivery and setting up power cables,
they are produced and delivered in several separate lengths. Cable
itself, consists of two cable terminations and arbitrary number of
cable joints, depending on the cable route length. Electrical stress
control is needed to prevent a dielectric breakdown at the end of the
insulation shield in both the air and cable insulation. Reliability of
cable joint depends on its materials, design, installation and operating
environment. The paper describes design and performance results for
new modeled cable joints. Design concepts, based on numerical
calculations, must be correct. An Equivalent Electrodes
Method/Boundary Elements Method-hybrid approach that allows
electromagnetic field calculations in multilayer dielectric media,
including inhomogeneous regions, is presented.
Abstract: Biodiesel production results in glycerol production as
the main by-product in biodiesel industry.One of the utilizations of
glycerol obtained from biodiesel production is as a cement grinding
aid (CGA). Results showed that crude glycerol content was 40.19%
whereas pure glycerol content was 82.15%. BSS value of the cement
with CGA supplementation was higher than that of nonsupplemented
cement (blank) indicating that CGA-supplemented
cement had higher fineness than the non-supplemented one. It was
also found that pure glycerol 95% and TEA 5% at 80ºC was the
optimum CGA used to result in finest cement with BSS value of
4.836 cm2/g. Residue test showed that the smallest percent residue
value (0.11%) was obtained in cement with supplementation of pure
glycerol 95% and TEA 5%. Results of residue test confirmed those of
BSS test showing that cement with supplementation of pure glycerol
95% and TEA 5% had the finest particle size.
Abstract: Increase in using internet makes some problems that
one of them is "internet anxiety". Internet anxiety is a type of anxious
that people may feel during surfing internet or using internet for their
educational purpose, blogging or streaming to digital libraries. The
goal of this study is evaluating of internet anxiety among the
management students. In this research Ealy's internet anxiety
questionnaire, consists of positive and negative items, is completed
by 310 participants. According to the findings, about 64.7% of them
were equal or below to mean anxiety score (50). The distribution of
internet anxiety scores was normal and there was no meaningful
difference between men-s and women's anxiety level in this sample.
Results also showed that there is no meaningful difference of internet
anxiety level between different fields of study in Management. This
evaluation will help managers to perform gap analysis between the
existent level and the desired one. Future work would be providing
techniques for abating human anxiety while using internet via human
computer interaction techniques.
Abstract: To measure the thickness of the subcutaneous adipose
tissue layer, a non-invasive optical measurement system (λ=1300 nm)
is introduced. Animal and human subjects are used for the
experiments. The results of human subjects are compared with the data
of ultrasound device measurements, and a high correlation (r=0.94 for
n=11) is observed. There are two modes in the corresponding signals
measured by the optical system, which can be explained by
two-layered and three-layered tissue models. If the target tissue is
thinner than the critical thickness, detected data using diffuse
reflectance method follow the three-layered tissue model, so the data
increase as the thickness increases. On the other hand, if the target
tissue is thicker than the critical thickness, the data follow the
two-layered tissue model, so they decrease as the thickness increases.
Abstract: Today modern simulations solutions in the wind turbine industry have achieved a high degree of complexity and detail in result. Limitations exist when it is time to validate model results against measurements. Regarding Model validation it is of special interest to identify mode frequencies and to differentiate them from the different excitations. A wind turbine is a complex device and measurements regarding any part of the assembly show a lot of noise. Input excitations are difficult or even impossible to measure due to the stochastic nature of the environment. Traditional techniques for frequency analysis or features extraction are widely used to analyze wind turbine sensor signals, but have several limitations specially attending to non stationary signals (Events). A new technique based on autoregresive analysis techniques is introduced here for a specific application, a comparison and examples related to different events in the wind turbine operations are presented.
Abstract: The purpose of this paper is to provide an overview on methodological aspects of the information technology outsourcing (ITO) surveys, in an attempt to improve the data quality and reporting in survey research. It is based on a review of thirty articles on ITO surveys and focuses on two commonly explored dimensions of ITO, namely what are outsourced and why should there be ITO. This study highlights weaknesses in ITO surveys including lack of a clear definition of population, lack of information regarding the sampling method used, not citing the response rate, no information pertaining to pilot testing of survey instrument and absence of information on internal validity in the use or reporting of surveys. This study represents an attempt with a limited scope to point to shortfalls in the use survey methodology in ITO, and thus raise awareness among researchers in enhancing the reliability of survey findings.
Abstract: Reasonably priced and well-constructed housing must
be an integral and element supporting a healthy society. The absence
of housing everyone in society can afford negatively affects the
people's health, education, ability to get jobs, develop their
community. Without access to decent housing, economic
development, integration of immigrants and inclusiveness, the society
is negatively impacted. Canada has a sterling record in creating
housing compared to many other nations around the globe. Canadian
housing gets support from a mature and responsive mortgage network
and a top-quality construction industry as well as safe and excellent
quality building materials that are readily available. Yet 1.7 million
Canadian households occupy substandard abodes. During the past
hundred years, Canada's government has made a wide variety of
attempts to provide decent residential facilities every Canadian can
afford. Despite these laudable efforts, today Canada is left with
housing that is inadequate for many Canadians. People who own their
housing are given all kinds of privileges and perks, while people with
relatively low incomes who rent their apartments or houses are
discriminated against.
To help solve these problems, zoning that is based on an
"inclusionary" philosophy is tool developed to help provide people
the affordable residences that they need. No, thirty years after its
introduction, this type of zoning has been shown effective in helping
build and provide Canadians with a houses or apartments they can
afford to pay for. Using this form of zoning can have different results
+depending on where and how it is used. After examining Canadian
affordable housing and four American cases where this type of
zoning was enforced in the USA, this makes various
recommendations for expanding Canadians' access to housing they
can afford.
Abstract: A zero dimensional model has been used to investigate
the combustion performance of a single cylinder direct injection
diesel engine fueled by biofuels with options like supercharging and
exhaust gas recirculation. The numerical simulation was performed at
constant speed. The indicated pressure, temperature diagrams are
plotted and compared for different fuels. The emissions of soot and
nitrous oxide are computed with phenomenological models. The
experimental work was also carried out with biodiesel (palm stearin
methyl ester) diesel blends, ethanol diesel blends to validate
simulation results with experimental results, and observed that the
present model is successful in predicting the engine performance with
biofuels.
Abstract: This paper reports the results of an experimental study
conducted to characterise the gas-liquid multiphase flows
experienced within a vertical riser transporting a range of gas-liquid
flow rates. The scale experiments were performed using an
air/silicone oil mixture within a 6 m long riser. The superficial air
velocities studied ranged from 0.047 to 2.836 m/ s, whilst
maintaining a liquid superficial velocity at 0.047 m/ s. Measurements
of the mean cross-sectional and time average radial void fraction
were obtained using a wire mesh sensor (WMS). The data were
recorded at an acquisition frequency of 1000 Hz over an interval of
60 seconds. For the range of flow conditions studied, the average
void fraction was observed to vary between 0.1 and 0.9. An analysis
of the data collected concluded that the observed void fraction was
strongly affected by the superficial gas velocity, whereby the higher
the superficial gas velocity, the higher was the observed average void
fraction. The average void fraction distributions observed were in
good agreement with the results obtained by other researchers. When
the air-silicone oil flows were fully developed reasonably symmetric
profiles were observed, with the shape of the symmetry profile being
strongly dependent on the superficial gas velocity.
Abstract: Transition theory has been used to derive the elasticplastic
and transitional stresses. Results obtained have been discussed
numerically and depicted graphically. It is observed that the rotating
disk made of incompressible material with inclusion require higher
angular speed to yield at the internal surface as compared to disk
made of compressible material. It is seen that the radial and
circumferential stresses are maximum at the internal surface with and
without edge load (for flat disk). With the increase in thickness
parameter (k = 2, 4), the circumferential stress is maximum at the
external surface while the radial stress is maximum at the internal
surface. From the figures drawn the disk with exponentially varying
thickness (k = 2), high angular speed is required for initial yielding at
internal surface as compared to flat disk and exponentially varying
thickness for k = 4 onwards. It is concluded that the disk made of
isotropic compressible material is on the safer side of the design as
compared to disk made of isotropic incompressible material as it
requires higher percentage increase in an angular speed to become
fully plastic from its initial yielding.
Abstract: People from different cultures favor web pages
characterized by the values of their culture and, therefore, tend to
prefer different characteristics of a website according to their cultural
values in terms of navigation, security, product information, customer
service, shopping and design tools. For a company aiming to
globalize its market it is useful to implement country specific cultural
interfaces and different web sites for countries with different cultures.
This paper, following the conclusions proposed by two models of
Hall and Hofstede, and the studies of Marcus and Gould, defines,
through an empirical analysis, the guidelines of web design for both
the Scandinavian countries and Malaysia.
Abstract: This paper describes an automated event detection and location system for water distribution pipelines which is based upon low-cost sensor technology and signature analysis by an Artificial
Neural Network (ANN). The development of a low cost failure sensor which measures the opacity or cloudiness of the local water
flow has been designed, developed and validated, and an ANN based system is then described which uses time series data produced by
sensors to construct an empirical model for time series prediction and
classification of events. These two components have been installed,
tested and verified in an experimental site in a UK water distribution
system. Verification of the system has been achieved from a series of
simulated burst trials which have provided real data sets. It is concluded that the system has potential in water distribution network
management.
Abstract: The Learning Management Systems present learning
environment which offers a collection of e-learning tools in a
package that allows a common interface and information sharing
among the tools. South East European University initial experience
in LMS was with the usage of the commercial LMS-ANGEL. After a
three year experience on ANGEL usage because of expenses that
were very high it was decided to develop our own software. As part
of the research project team for the in-house design and development
of the new LMS, we primarily had to select the features that would
cover our needs and also comply with the actual trends in the area of
software development, and then design and develop the system. In
this paper we present the process of LMS in-house development for
South East European University, its architecture, conception and
strengths with a special accent on the process of migration and
integration with other enterprise applications.
Abstract: Electronic seal is an electronic device to check the
authenticity and integrity of freight containers at the point of arrival.
While RFID-based eSeals are gaining more acceptances and there are
also some standardization processes for these devices, a recent
research revealed that the current RFID-based eSeals are vulnerable to
various attacks. In this paper, we provide a feasible solution to
enhance the security of active RFID-based eSeals. Our approach is to
use an authentication and key agreement protocol between eSeal and
reader device, enabling data encryption and integrity check. Our
protocol is based on the use of block cipher AES, which is reasonable
since a block cipher can also be used for many other security purposes
including data encryption and pseudo-random number generation. Our
protocol is very simple, and it is applicable to low-end active RFID
eSeals.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: This paper presents a system for tracking the movement of laparoscopic instruments which is based on an orthogonal system of webcams and video image processing. The movements are captured with two webcams placed orthogonally inside of the physical trainer. On the image, the instruments were detected by using color markers placed on the distal tip of each instrument. The 3D position of the tip of the instrument within the work space was obtained by linear triangulation method. Preliminary results showed linearity and repeatability in the motion tracking with a resolution of 0.616 mm in each axis; the accuracy of the system showed a 3D instrument positioning error of 1.009 ± 0.101 mm. This tool is a portable and low-cost alternative to traditional tracking devices and a trustable method for the objective evaluation of the surgeon’s surgical skills.
Abstract: REY area has been located in Tehran Province and several archaeological ruins of this area indicate that the settlement in this area has been started since several thousand years ago. In this paper, the main investigation items consist of analysis of oil components and groundwater quality inside the wells. By finding the contents of oil in the well, it is possible to find out the pollution source by comparing the oil contents of well with other oil products that are used inside and outside of the oil farm. Investigation items consist of analysis of BTEX (Benzene, Toluene, Ethyl-benzene, Xylene), Gas chromatographic distillation characteristics, Water content, Density, Sulfur content, Lead content, Atmospheric distillation, MTBE(Methyl tertiary butyl ether). Analysis of polluting oil components showed that except MW(Monitoring Well)10 and MW 15 that oil with slightly heavy components was detected in them; with a high possibility the polluting oil is light oil.
Abstract: The forming process parameters of Selective Laser
Sintering(SLS) directly affect the forming efficiency and forming
quality. Therefore, to determine reasonable process parameters is
particularly important. In this paper, the weight of each target of the
forming quality and efficiency is firstly calculated with the Analytic
Hierarchy Process. And then the size of each target is measured by
orthogonal experiment. Finally, the sum of the product of each target
with the weight is compared to the process parameters in each group
and obtained the optimal molding process parameters.