Abstract: It is important to remove manganese from water
because of its effects on human and the environment. Human
activities are one of the biggest contributors for excessive manganese
concentration in the environment. The proposed method to remove
manganese in aqueous solution by using adsorption as in carbon
nanotubes (CNT) at different parameters: The parameters are CNT
dosage, pH, agitation speed and contact time. Different pHs are pH
6.0, pH 6.5, pH 7.0, pH 7.5 and pH 8.0, CNT dosages are 5mg,
6.25mg, 7.5mg, 8.75mg or 10mg, contact time are 10 min, 32.5 min,
55 min, 87.5 min and 120 min while the agitation speeds are 100rpm,
150rpm, 200rpm, 250rpm and 300rpm. The parameters chosen for
experiments are based on experimental design done by using Central
Composite Design, Design Expert 6.0 with 4 parameters, 5 levels and
2 replications. Based on the results, condition set at pH 7.0, agitation
speed of 300 rpm, 7.5mg and contact time 55 minutes gives the
highest removal with 75.5%. From ANOVA analysis in Design
Expert 6.0, the residual concentration will be very much affected by
pH and CNT dosage. Initial manganese concentration is 1.2mg/L
while the lowest residual concentration achieved is 0.294mg/L,
which almost satisfy DOE Malaysia Standard B requirement.
Therefore, further experiments must be done to remove manganese
from model water to the required standard (0.2 mg/L) with the initial
concentration set to 0.294 mg/L.
Abstract: The Application of e-health solutions has brought superb advancements in the health care industry. E-health solutions have already been embraced in the industrialized countries. In an effort to catch up with the growth, the developing countries have strived to revolutionize the healthcare industry by use of Information technology in different ways. Based on a technology assessment carried out in Kenya – one of the developing countries – and using multiple case studies in Nyanza Province, this work focuses on an investigation on how five rural hospitals are adapting to the technology shift. The issues examined include the ICT infrastructure and e-health technologies in place, the knowledge of participants in terms of benefits gained through the use of ICT and the challenges posing barriers to the use of ICT technologies in these hospitals. The results reveal that the ICT infrastructure in place is inadequate for e-health implementations as a result to various challenges that exist. Consequently, suggestions on how to tackle the various challenges have been addressed in this paper.
Abstract: In non destructive testing by radiography, a perfect
knowledge of the weld defect shape is an essential step to
appreciate the quality of the weld and make decision on its
acceptability or rejection. Because of the complex nature of the
considered images, and in order that the detected defect region
represents the most accurately possible the real defect, the choice
of thresholding methods must be done judiciously. In this paper,
performance criteria are used to conduct a comparative study of
four non parametric histogram thresholding methods for automatic
extraction of weld defect in radiographic images.
Abstract: This paper presents the effectiveness of artificial
intelligent technique to apply for pattern recognition and
classification of Partial Discharge (PD). Characteristics of PD signal
for pattern recognition and classification are computed from the
relation of the voltage phase angle, the discharge magnitude and the
repeated existing of partial discharges by using statistical and fractal
methods. The simplified fuzzy ARTMAP (SFAM) is used for pattern
recognition and classification as artificial intelligent technique. PDs
quantities, 13 parameters from statistical method and fractal method
results, are inputted to Simplified Fuzzy ARTMAP to train system
for pattern recognition and classification. The results confirm the
effectiveness of purpose technique.
Abstract: Recently in the field of bridges that are newly built or
repaired, fast construction is required more than ever. For these
reasons, precast prefabricated bridge that enables rapid construction is
actively discussed and studied today. In South Korea, it is called
modular bridge. Cross beam is an integral component of modular
bridge. It functions for load distribution, reduction of bending
moment, resistance of horizontal strength on lateral upper structure. In
this study, the structural characteristics of domestic and foreign cross
beam types were compared. Based on this, alternative cross beam
connection types suitable for modular bridge were selected. And
bulb-T girder specimens were fabricated with each type of connection.
The behavior of each specimen was analyzed under static loading, and
cross beam connection type which is expected to be best suited to
modular bridge proposed.
Abstract: In this paper, SFQ (Start Time Fair Queuing)
algorithm is analyzed when this is applied in computer networks to
know what kind of behavior the traffic in the net has when different
data sources are managed by the scheduler. Using the NS2 software
the computer networks were simulated to be able to get the graphs
showing the performance of the scheduler. Different traffic sources
were introduced in the scripts, trying to establish the real scenario.
Finally the results were that depending on the data source, the traffic
can be affected in different levels, when Constant Bite Rate is
applied, the scheduler ensures a constant level of data sent and
received, but the truth is that in the real life it is impossible to ensure
a level that resists the changes in work load.
Abstract: Conventional WBL is effective for meaningful student, because rote student learn by repeating without thinking or trying to understand. It is impossible to have full benefit from conventional WBL. Understanding of rote student-s intention and what influences it becomes important. Poorly designed user interface will discourage rote student-s cultivation and intention to use WBL. Thus, user interface design is an important factor especially when WBL is used as comprehensive replacement of conventional teaching. This research proposes the influencing factors that can enhance student-s intention to use the system. The enhanced TAM is used for evaluating the proposed factors. The research result points out that factors influencing rote student-s intention are Perceived Usefulness of Homepage Content Structure, Perceived User Friendly Interface, Perceived Hedonic Component, and Perceived (homepage) Visual Attractiveness.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.
Abstract: In this paper, an automatic detecting algorithm for
QRS complex detecting was applied for analyzing ECG recordings
and five criteria for dangerous arrhythmia diagnosing are applied for a
protocol type of automatic arrhythmia diagnosing system. The
automatic detecting algorithm applied in this paper detected the
distribution of QRS complexes in ECG recordings and related
information, such as heart rate and RR interval. In this investigation,
twenty sampled ECG recordings of patients with different pathologic
conditions were collected for off-line analysis. A combinative
application of four digital filters for bettering ECG signals and
promoting detecting rate for QRS complex was proposed as
pre-processing. Both of hardware filters and digital filters were
applied to eliminate different types of noises mixed with ECG
recordings. Then, an automatic detecting algorithm of QRS complex
was applied for verifying the distribution of QRS complex. Finally,
the quantitative clinic criteria for diagnosing arrhythmia were
programmed in a practical application for automatic arrhythmia
diagnosing as a post-processor. The results of diagnoses by automatic
dangerous arrhythmia diagnosing were compared with the results of
off-line diagnoses by experienced clinic physicians. The results of
comparison showed the application of automatic dangerous
arrhythmia diagnosis performed a matching rate of 95% compared
with an experienced physician-s diagnoses.
Abstract: This paper deals with the effect of a power transformer’s vector group on the basic voltage sag characteristics during unbalanced faults at a meshed or radial power network. Specifically, the propagation of voltage sags through a power transformer is studied with advanced short-circuit analysis. A smart method to incorporate this effect on analytical mathematical expressions is proposed. Based on this methodology, the positive effect of transformers of certain vector groups on the mitigation of the expected number of voltage sags per year (sag frequency) at the terminals of critical industrial customers can be estimated.
Abstract: The main problem for recognition of handwritten Persian digits using Neural Network is to extract an appropriate feature vector from image matrix. In this research an asymmetrical segmentation pattern is proposed to obtain the feature vector. This pattern can be adjusted as an optimum model thanks to its one degree of freedom as a control point. Since any chosen algorithm depends on digit identity, a Neural Network is used to prevail over this dependence. Inputs of this Network are the moment of inertia and the center of gravity which do not depend on digit identity. Recognizing the digit is carried out using another Neural Network. Simulation results indicate the high recognition rate of 97.6% for new introduced pattern in comparison to the previous models for recognition of digits.
Abstract: When the failure function is monotone, some monotonic reliability methods are used to gratefully simplify and facilitate the reliability computations. However, these methods often work in a transformed iso-probabilistic space. To this end, a monotonic simulator or transformation is needed in order that the transformed failure function is still monotone. This note proves at first that the output distribution of failure function is invariant under the transformation. And then it presents some conditions under which the transformed function is still monotone in the newly obtained space. These concern the copulas and the dependence concepts. In many engineering applications, the Gaussian copulas are often used to approximate the real word copulas while the available information on the random variables is limited to the set of marginal distributions and the covariances. So this note catches an importance on the conditional monotonicity of the often used transformation from an independent random vector into a dependent random vector with Gaussian copulas.
Abstract: The objective of current study is to investigate the
differences of winning and losing teams in terms of goal scoring and
passing sequences. Total of 31 matches from UEFA-EURO 2012
were analyzed and 5 matches were excluded from analysis due to
matches end up drawn. There are two groups of variable used in the
study which is; i. the goal scoring variable and: ii. passing sequences
variable. Data were analyzed using Wilcoxon matched pair rank test
with significant value set at p < 0.05. Current study found the timing
of goal scored was significantly higher for winning team at 1st half
(Z=-3.416, p=.001) and 2nd half (Z=-3.252, p=.001). The scoring
frequency was also found to be increase as time progressed and the
last 15 minutes of the game was the time interval the most goals
scored. The indicators that were significantly differences between
winning and losing team were the goal scored (Z=-4.578, p=.000),
the head (Z=-2.500, p=.012), the right foot (Z=-3.788,p=.000),
corner (Z=-.2.126,p=.033), open play (Z=-3.744,p=.000), inside the
penalty box (Z=-4.174, p=.000) , attackers (Z=-2.976, p=.003) and
also the midfielders (Z=-3.400, p=.001). Regarding the passing
sequences, there are significance difference between both teams in
short passing sequences (Z=-.4.141, p=.000). While for the long
passing, there were no significance difference (Z=-.1.795, p=.073).
The data gathered in present study can be used by the coaches to
construct detailed training program based on their objectives.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any existing
network infrastructure or centralized administration. Because of the
limited transmission range of wireless network interfaces, multiple
"hops" may be needed to exchange data across the network. In order
to facilitate communication within the network, a routing protocol is
used to discover routes between nodes. The primary goal of such an
ad hoc network routing protocol is correct and efficient route
establishment between a pair of nodes so that messages may be
delivered in a timely manner. Route construction should be done
with a minimum of overhead and bandwidth consumption. This paper
examines two routing protocols for mobile ad hoc networks– the
Destination Sequenced Distance Vector (DSDV), the table- driven
protocol and the Ad hoc On- Demand Distance Vector routing
(AODV), an On –Demand protocol and evaluates both protocols
based on packet delivery fraction, normalized routing load, average
delay and throughput while varying number of nodes, speed and
pause time.
Abstract: In this paper we propose and examine an Adaptive
Neuro-Fuzzy Inference System (ANFIS) in Smoothing Transition
Autoregressive (STAR) modeling. Because STAR models follow
fuzzy logic approach, in the non-linear part fuzzy rules can be
incorporated or other training or computational methods can be
applied as the error backpropagation algorithm instead to nonlinear
squares. Furthermore, additional fuzzy membership functions can be
examined, beside the logistic and exponential, like the triangle,
Gaussian and Generalized Bell functions among others. We examine
two macroeconomic variables of US economy, the inflation rate and
the 6-monthly treasury bills interest rates.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.
Abstract: This paper presents three-phase evolution search methodology to automatically design fuzzy logic controllers (FLCs) that can work in a wide range of operating conditions. These include varying load, parameter variations, and unknown external disturbances. The three-phase scheme consists of an exploration phase, an exploitation phase and a robustness phase. The first two phases search for FLC with high accuracy performances while the last phase aims at obtaining FLC providing the best compromise between the accuracy and robustness performances. Simulations were performed for direct-drive two-axis robot arm. The evolved FLC with the proposed design technique found to provide a very satisfactory performance under the wide range of operation conditions and to overcome problem associated with coupling and nonlinearities characteristics inherent to robot arms.
Abstract: Feature selection plays an important role in applications with high dimensional data. The assessment of the stability of feature selection/ranking algorithms becomes an important issue when the dataset is small and the aim is to gain insight into the underlying process by analyzing the most relevant features. In this work, we propose a graphical approach that enables to analyze the similarity between feature ranking techniques as well as their individual stability. Moreover, it works with whatever stability metric (Canberra distance, Spearman's rank correlation coefficient, Kuncheva's stability index,...). We illustrate this visualization technique evaluating the stability of several feature selection techniques on a spectral binary dataset. Experimental results with a neural-based classifier show that stability and ranking quality may not be linked together and both issues have to be studied jointly in order to offer answers to the domain experts.
Abstract: A mathematical model for the transmission of SARS is developed. In addition to dividing the population into susceptible (high and low risk), exposed, infected, quarantined, diagnosed and recovered classes, we have included a class called untraced. The model simulates the Gompertz curves which are the best representation of the cumulative numbers of probable SARS cases in Hong Kong and Singapore. The values of the parameters in the model which produces the best fit of the observed data for each city are obtained by using a differential evolution algorithm. It is seen that the values for the parameters needed to simulate the observed daily behaviors of the two epidemics are different.
Abstract: BRI-STARS (BRIdge Stream Tube model for Alluvial
River Simulation) program was used to investigate the scour depth around bridge piers in some of the major river systems in Iran. Model
calibration was performed by collecting different field data. Field data are cataloged on three categories, first group of bridges that
their rivers bed are formed by fine material, second group of bridges
that their rivers bed are formed by sand material, and finally bridges that their rivers bed are formed by gravel or cobble materials.
Verification was performed with some field data in Fars Province. Results show that for wide piers, computed scour depth is more than
measured one. In gravel bed streams, computed scour depth is greater
than measured scour depth, the reason is due to formation of armor layer on bed of channel. Once this layer is eroded, the computed
scour depth is close to the measured one.