Abstract: THEOS is the first earth observation spacecraft of Thailand which was launched on the 1st October 2008 and is currently operated by GISTDA. The transfer phase has been performed by Astrium Flight Dynamics team leading to a hand over to GISTDA teams starting mid-October 2008. The THEOS spacecraft-s orbit is LEO and has the same repetitivity (14+5/26) as the SPOT spacecraft, i.e. the same altitude of 822 km but it has a different mean local solar time (LST). Ground track maintenance manoeuvres are performed to maintain the ground track within a predefined control band around the reference ground track and the band is ±40 km for THEOS spacecraft. This paper presents the first ground track maintenance manoeuvre of THEOS spacecraft and the detailed results. In addition, it also includes one and a half year of operation as seen by GISTDA operators. It finally describes the foreseenable activities for the next orbit control manoeuvre (OCM) preparation.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Abstract: As emails communications have no consistent
authentication procedure to ensure the authenticity, we present an
investigation analysis approach for detecting forged emails based on
Random Forests and Naïve Bays classifiers. Instead of investigating
the email headers, we use the body content to extract a unique writing
style for all the possible suspects. Our approach consists of four main
steps: (1) The cybercrime investigator extract different effective
features including structural, lexical, linguistic, and syntactic
evidence from previous emails for all the possible suspects, (2) The
extracted features vectors are normalized to increase the accuracy
rate. (3) The normalized features are then used to train the learning
engine, (4) upon receiving the anonymous email (M); we apply the
feature extraction process to produce a feature vector. Finally, using
the machine learning classifiers the email is assigned to one of the
suspects- whose writing style closely matches M. Experimental
results on real data sets show the improved performance of the
proposed method and the ability of identifying the authors with a
very limited number of features.
Abstract: The Bayesian Optimization Algorithm (BOA) is an algorithm based on the estimation of distributions. It uses techniques from modeling data by Bayesian networks to estimating the joint distribution of promising solutions. To obtain the structure of Bayesian network, different search algorithms can be used. The key point that BOA addresses is whether the constructed Bayesian network could generate new and useful solutions (strings), which could lead the algorithm in the right direction to solve the problem. Undoubtedly, this ability is a crucial factor of the efficiency of BOA. Varied search algorithms can be used in BOA, but their performances are different. For choosing better ones, certain suitable method to present their ability difference is needed. In this paper, a greedy search algorithm and a stochastic search algorithm are used in BOA to solve certain optimization problem. A method using Kullback-Leibler (KL) Divergence to reflect their difference is described.
Abstract: This paper presents the visual control flow support of Visual Modeling and Transformation System (VMTS), which facilitates composing complex model transformations out of simple transformation steps and executing them. The VMTS Visual Control Flow Language (VCFL) uses stereotyped activity diagrams to specify control flow structures and OCL constraints to choose between different control flow branches. This work discusses the termination properties of VCFL and provides an algorithm to support the termination analysis of VCFL transformations.
Abstract: Drought is a phenomenon caused by
environmental and climatic changes. This phenomenon is
affected by shortage of rainfall and temperature. Dust is one
of important environmental problems caused by climate
change and drought. With recent multi-year drought, many
environmental crises caused by dust in Iran and Middle East.
Dust in the vast areas of the provinces occurs with high
frequency. By dust affecting many problems created in terms
of health, social and economic. In this study, we tried to study
the most important factors causing dust. In this way we have
used the satellite images and meteorological data. Finally,
strategies to deal with the dust will be mentioned.
Abstract: Malware is software which was invented and meant for doing harms on computers. Malware is becoming a significant threat in computer network nowadays. Malware attack is not just only involving financial lost but it can also cause fatal errors which may cost lives in some cases. As new Internet Protocol version 6 (IPv6) emerged, many people believe this protocol could solve most malware propagation issues due to its broader addressing scheme. As IPv6 is still new compares to native IPv4, some transition mechanisms have been introduced to promote smoother migration. Unfortunately, these transition mechanisms allow some malwares to propagate its attack from IPv4 to IPv6 network environment. In this paper, a proof of concept shall be presented in order to show that some existing IPv4 malware detection technique need to be improvised in order to detect malware attack in dual-stack network more efficiently. A testbed of dual-stack network environment has been deployed and some genuine malware have been released to observe their behaviors. The results between these different scenarios will be analyzed and discussed further in term of their behaviors and propagation methods. The results show that malware behave differently on IPv6 from the IPv4 network protocol on the dual-stack network environment. A new detection technique is called for in order to cater this problem in the near future.
Abstract: Abrasive waterjet cutting (AWJ) is a highly efficient
method for cutting almost any type of material. When holes shall be
cut the waterjet first needs to pierce the material.This paper presents a
vast experimental analysis of piercing parameters effect on piercing
time. Results from experimentation on feed rates, work piece
thicknesses, abrasive flow rates, standoff distances and water
pressure are also presented as well as studies on three methods for
dynamic piercing. It is shown that a large amount of time and
resources can be saved by choosing the piercing parameters in a
correct way. The large number of experiments puts demands on the
experimental setup. An automated experimental setup including
piercing detection is presented to enable large series of experiments
to be carried out efficiently.
Abstract: This study suggests a model of a new set of evaluation criteria that will be used to measure the efficiency of real-world E-commerce websites. Evaluation criteria include design, usability and performance for websites, the Data Envelopment Analysis (DEA) technique has been used to measure the websites efficiency. An efficient Web site is defined as a site that generates the most outputs, using the smallest amount of inputs. Inputs refer to measurements representing the amount of effort required to build, maintain and perform the site. Output is amount of traffic the site generates. These outputs are measured as the average number of daily hits and the average number of daily unique visitors.
Abstract: This paper describes a novel monitoring scheme to
minimize total active power in digital circuits depend on the demand
frequency, by adjusting automatically both supply voltage and
threshold voltages based on circuit operating conditions such as
temperature, process variations, and desirable frequency. The delay
monitoring results, will be control and apply so as to be maintained at
the minimum value at which the chip is able to operate for a given
clock frequency. Design details of power monitor are examined using
simulation framework in 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 40 μW for 32nm technology;
moreover the results show that our proposed circuit design is not far
sensitive to the temperature variations and also process variations.
Besides, uses the simple blocks which offer good sensitivity, high
speed, the continuously feedback loop. This design provides up to
40% reduction in power consumption in active mode.
Abstract: The scientific perspective, the practice area of physical education and sports activities improve power capacity in all its forms of expression, being a generator of the research topics. Today theories that strength training athletes and slow down development progress will affect the strength and flexibility are discredited. On the other hand there are sectors and / or samples whose results are sports of the way higher manifestation of power as a result of the composition of the force and velocity, being based in this respect on the systematic and continuous development of both bio-motric capacities said. Training of force for children was and is controversial. Teama de accidentări sau a stopării premature a procesului de creştere a făcut ca în trecut copiii să fie ţinuţi departe de lucrul cu diferite greutăţi.Fear of injury or premature stop the growth process in the past made the children to be kept away from working with different weights. Recent studies have shown that the risk of accidents is relatively small and the strength training can help prevent them. For example, most accidents occur at the level of athletics ligaments and tendons. From this point of view, it can be said that a progressive intervention of force training, optimal design, will help enhancing their process, such as athlete much better prepared to meet training requests and competitions. Preparation of force provides a solid basis for further phases in the highest performance.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: In this paper a systematic method via H∞ control
design is proposed to select a sensor set that satisfies a number
of input criteria for a MAGLEV suspension system. The proposed
method recovers a number of optimised controllers for each possible
sensor set that satisfies the performance and constraint criteria using
evolutionary algorithms.
Abstract: In this paper we will develop further the sequential
life test approach presented in a previous article by [1] using an
underlying two parameter Weibull sampling distribution. The
minimum life will be considered equal to zero. We will again provide
rules for making one of the three possible decisions as each
observation becomes available; that is: accept the null hypothesis H0;
reject the null hypothesis H0; or obtain additional information by
making another observation. The product being analyzed is a new
type of a low alloy-high strength steel product. To estimate the shape
and the scale parameters of the underlying Weibull model we will use
a maximum likelihood approach for censored failure data. A new
example will further develop the proposed sequential life testing
approach.
Abstract: This paper present a new method for design of power
system stabilizer (PSS) based on sliding mode control (SMC)
technique. The control objective is to enhance stability and improve
the dynamic response of the multi-machine power system. In order to
test effectiveness of the proposed scheme, simulation will be carried
out to analyze the small signal stability characteristics of the system
about the steady state operating condition following the change in
reference mechanical torque and also parameters uncertainties. For
comparison, simulation of a conventional control PSS (lead-lag
compensation type) will be carried out. The main approach is
focusing on the control performance which later proven to have the
degree of shorter reaching time and lower spike.
Abstract: The requirements analysis, modeling, and simulation have consistently been one of the main challenges during the development of complex systems. The scenarios and the state machines are two successful models to describe the behavior of an interactive system. The scenarios represent examples of system execution in the form of sequences of messages exchanged between objects and are a partial view of the system. In contrast, state machines can represent the overall system behavior. The automation of processing scenarios in the state machines provide some answers to various problems such as system behavior validation and scenarios consistency checking. In this paper, we propose a method for translating scenarios in state machines represented by Discreet EVent Specification and procedure to detect implied scenarios. Each induced DEVS model represents the behavior of an object of the system. The global system behavior is described by coupling the atomic DEVS models and validated through simulation. We improve the validation process with integrating formal methods to eliminate logical inconsistencies in the global model. For that end, we use the Z notation.
Abstract: The tree structured approach of non-uniform filterbank
(NUFB) is normally used in perfect reconstruction (PR). The PR is
not always feasible due to certain limitations, i.e, constraints in
selecting design parameters, design complexity and some times
output is severely affected by aliasing error if necessary and
sufficient conditions of PR is not satisfied perfectly. Therefore, there
has been generalized interest of researchers to go for near perfect
reconstruction (NPR). In this proposed work, an optimized tree
structure technique is used for the design of NPR non-uniform
filterbank. Window functions of Blackman family are used to design
the prototype FIR filter. A single variable linear optimization is used
to minimize the amplitude distortion. The main feature of the
proposed design is its simplicity with linear phase property.
Abstract: Ringing effect is one of the most annoying visual
artifacts in digital video. It is a significant factor of subjective quality
deterioration. However, there is a widely-accepted misunderstanding
of its cause. In this paper, we propose a reasonable interpretation of the
cause of ringing effect. Based on the interpretation, we suggest further
two methods to reduce ringing effect in DCT-based video coding. The
methods adaptively adjust quantizers according to video features. Our
experiments proved that the methods could efficiently improve
subjective quality with acceptable additional computing costs.
Abstract: The Expert Witness Testimony in the Battered
Woman Syndrome Expert witness testimony (EWT) is a kind of
information given by an expert specialized in the field (here in BWS)
to the jury in order to help the court better understand the case. EWT
does not always work in favor of the battered women. Two main
decision-making models are discussed in the paper: the Mathematical
model and the Explanation model. In the first model, the jurors
calculate ″the importance and strength of each piece of evidence″
whereas in the second model they try to integrate the EWT with the
evidence and create a coherent story that would describe the crime.
The jury often misunderstands and misjudges battered women for
their action (or in this case inaction). They assume that these women
are masochists and accept being mistreated for if a man abuses a
woman constantly, she should and could divorce him or simply leave
at any time. The research in the domain found that indeed, expert
witness testimony has a powerful influence on juror’s decisions thus
its quality needs to be further explored. One of the important factors
that need further studies is a bias called the dispositionist worldview
(a belief that what happens to people is of their own doing). This
kind of attributional bias represents a tendency to think that a
person’s behavior is due to his or her disposition, even when the
behavior is clearly attributed to the situation. Hypothesis The
hypothesis of this paper is that if a juror has a dispositionist
worldview then he or she will blame the rape victim for triggering the
assault. The juror would therefore commit the fundamental
attribution error and believe that the victim’s disposition caused the
rape and not the situation she was in. Methods The subjects in the
study were 500 randomly sampled undergraduate students from
McGill, Concordia, Université de Montréal and UQAM.
Dispositional Worldview was scored on the Dispositionist
Worldview Questionnaire. After reading the Rape Scenarios, each
student was asked to play the role of a juror and answer a
questionnaire consisting of 7 questions about the responsibility,
causality and fault of the victim. Results The results confirm the
hypothesis which states that if a juror has a dispositionist worldview
then he or she will blame the rape victim for triggering the assault.
By doing so, the juror commits the fundamental attribution error
because he will believe that the victim’s disposition, and not the
constraints or opportunities of the situation, caused the rape scenario.