Abstract: Collective action can be an effective means for local development as well as important strategy to enhance livelihoods especially among rural people. This article explores the level of collective action among members of Fishermen-s Wives Group (KUNITA) in Malaysia. KUNITA was established by the Malaysian Fishery Development Authority (LKIM) with an objective to increase the socio-economic status of fishermen-s families. The members who are mostly the wives and daughters of fishermen are strongly encouraged by LKIM to venture into entrepreneurship activities. The objective of this research was to see the level of collective action among members in KUNITA groups in the state of Selangor. The finding shows that high level of collective action among KUNITA members is strongly based on volunteerism. However, the level of cooperation among members in the group is relatively low. The findings present significant challenges for the group in maintaining the sustainability of KUNITA organization.
Abstract: Owing the fact that optimization of business process
is a crucial requirement to navigate, survive and even thrive in
today-s volatile business environment, this paper presents a
framework for selecting a best-fit optimization package for solving
complex business problems. Complexity level of the problem and/or
using incorrect optimization software can lead to biased solutions of
the optimization problem. Accordingly, the proposed framework
identifies a number of relevant factors (e.g. decision variables,
objective functions, and modeling approach) to be considered during
the evaluation and selection process. Application domain, problem
specifications, and available accredited optimization approaches are
also to be regarded. A recommendation of one or two optimization
software is the output of the framework which is believed to provide
the best results of the underlying problem. In addition to a set of
guidelines and recommendations on how managers can conduct an
effective optimization exercise is discussed.
Abstract: In order to evaluate the relationship between the sulphur (S), glucose (G), nitrogen (N) and plant residues (st), sulphur immobilization and microbial transformation were monitored in five soil samples from 0-30 cm of Bastam farmers fields of Shahrood area following 11 treatments with different levels of Sulphur (S), glucose (G), N and plant residues (wheat straw) in a randomized block design with three replications and incubated over 20, 45 and 60 days, the immobilization of SO4 -2-S presented as a percentage of that added, was inversely related to its addition rate. Additions of glucose and plant residues increased with the C-to-S ratio of the added amendments, irrespective of their origins (glucose and plant residues). In the presence of C sources (glucose or plant residues). N significantly increased the immobilization of SO4 -2-S, whilst the effect of N was insignificant in the absence of a C amendment. In first few days the amounts of added SO4 -2-S immobilized were linearly correlated with the amounts of added S recovered in the soil microbial biomass. With further incubation the proportions of immobilized SO4 -2-S remaining as biomass-S decreased. Decrease in biomass-S was thought to be due to the conversion of biomass-S into soil organic-S. Glucose addition increased the immobilization (microbial utilization and incorporation into the soil organic matter) of native soil SO4 -2-S. However, N addition enhance the mineralization of soil organic-S, increasing the concentration of SO4 - 2-S in soil.
Abstract: In molecular biology, microarray technology is widely and successfully utilized to efficiently measure gene activity. If working with less studied organisms, methods to design custom-made microarray probes are available. One design criterion is to select probes with minimal melting temperature variances thus ensuring similar hybridization properties. If the microarray application focuses on the investigation of metabolic pathways, it is not necessary to cover the whole genome. It is more efficient to cover each metabolic pathway with a limited number of genes. Firstly, an approach is presented which minimizes the overall melting temperature variance of selected probes for all genes of interest. Secondly, the approach is extended to include the additional constraints of covering all pathways with a limited number of genes while minimizing the overall variance. The new optimization problem is solved by a bottom-up programming approach which reduces the complexity to make it computationally feasible. The new method is exemplary applied for the selection of microarray probes in order to cover all fungal secondary metabolite gene clusters for Aspergillus terreus.
Abstract: This study was set to determine the antimicrobial
activities of brine salting, chlorinated solution, and oil frying
treatments on enteric bacteria and fungi in Rastrineobola argentea
fish from fish landing beaches within L. Victoria basin of western
Kenya. Statistical differences in effectiveness of the different
treatment methods was determined by single factor ANOVA, and
paired two-tail t-Test was performed to compare the differences in
moisture contents before and after storage. Oil fried fish recorded the
lowest microbial loads, sodium chloride at 10% concentration was
the second most effective and chlorinated solution even at 150ppm
was the least effective against the bacteria and fungi in fish. Moisture
contents of the control and treated fish were significantly lower after
storage. These results show that oil frying of fish should be adopted
for processing and preserving Rastrineobola argentea which is the
most abundant and affordable fish species from Lake Victoria.
Abstract: The limit load carrying capacity of functionally
graded materials (FGM) circular plates subjected to an arbitrary
rotationally symmetric loading has been computed. It is provided that
the plate material behaves rigid perfectly plastic and obeys either the
Square or the Tresca yield criterion. To this end the upper and lower
bound principles of limit analysis are employed to determine the
exact value for the limiting load. The correctness of the result are
verified and finally limiting loads for two examples namely; through
radius and through thickness FGM circular plates with simply
supported edges are calculated, respectively and moreover, the values
of critical loading factor are determined.
Abstract: This paper aims at a new challenge of customer
satisfaction on mobile customer relationship management. In this
paper presents a conceptualization of mCRM on its unique
characteristics of customer satisfaction. Also, this paper develops an
empirical framework in conception of customer satisfaction in
mCRM. A single-case study is applied as the methodology. In order to
gain an overall view of the empirical case, this paper accesses to
invisible and important information of company in this investigation.
Interview is the key data source form the main informants of the
company through which the issues are identified and the proposed
framework is built. It supports the development of customer
satisfaction in mCRM; links this theoretical framework into practice;
and provides the direction for future research. Therefore, this paper is
very useful for the industries as it helps them to understand how
customer satisfaction changes the mCRM structure and increase the
business competitive advantage. Finally, this paper provides a
contribution in practice by linking a theoretical framework in
conception of customer satisfaction in mCRM for companies to a
practical real case.
Abstract: The scientific achievements coming from molecular
biology depend greatly on the capability of computational
applications to analyze the laboratorial results. A comprehensive
analysis of an experiment requires typically the simultaneous study
of the obtained dataset with data that is available in several distinct
public databases. Nevertheless, developing a centralized access to
these distributed databases rises up a set of challenges such as: what
is the best integration strategy, how to solve nomenclature clashes,
how to solve database overlapping data and how to deal with huge
datasets. In this paper we present GeNS, a system that uses a simple and yet innovative approach to address several biological data integration issues. Compared with existing systems, the main
advantages of GeNS are related to its maintenance simplicity and to its coverage and scalability, in terms of number of supported
databases and data types. To support our claims we present the current use of GeNS in two concrete applications. GeNS currently contains more than 140 million of biological relations and it can be
publicly downloaded or remotely access through SOAP web services.
Abstract: The objective of present work is to stimulate the
machining of material by electrical discharge machining (EDM) to
give effect of input parameters like discharge current (Ip), pulse on
time (Ton), pulse off time (Toff) which can bring about changes in the
output parameter, i.e. material removal rate. Experimental data was
gathered from die sinking EDM process using copper electrode and
Medium Carbon Steel (AISI 1040) as work-piece. The rules of
membership function (MF) and the degree of closeness to the
optimum value of the MMR are within the upper and lower range of
the process parameters. It was found that proposed fuzzy model is in
close agreement with the experimental results. By Intelligent, model
based design and control of EDM process parameters in this study
will help to enable dramatically decreased product and process
development cycle times.
Abstract: The research on two-wheeled inverted pendulum (TWIP) mobile robots or commonly known as balancing robots have gained momentum over the last decade in a number of robotic laboratories around the world. This paper describes the hardware design of such a robot. The objective of the design is to develop a TWIP mobile robot as well as MATLAB interfacing configuration to be used as flexible platform comprises of embedded unstable linear plant intended for research and teaching purposes. Issues such as selection of actuators and sensors, signal processing units, MATLAB Real Time Workshop coding, modeling and control scheme will be addressed and discussed. The system is then tested using a wellknown state feedback controller to verify its functionality.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: The kinetics of palm oil catalytic cracking over
aluminum containing mesoporous silica Al-MCM-41 (5% Al) was
investigated in a batch autoclave reactor at the temperatures range of
573 – 673 K. The catalyst was prepared by using sol-gel technique
and has been characterized by nitrogen adsorption and x-ray
diffraction methods. Surface area of 1276 m2/g with average pore
diameter of 2.54 nm and pore volume of 0.811 cm3/g was obtained.
The experimental catalytic cracking runs were conducted using 50 g
of oil and 1 g of catalyst. The reaction pressure was recorded at
different time intervals and the data were analyzed using Levenberg-
Marquardt (LM) algorithm using polymath software. The results
show that the reaction order was found to be -1.5 and activation
energy of 3200 J/gmol.
Abstract: The forest fires in Thailand are annual occurrence which is the cause of air pollutions. This study intended to estimate the emission from forest fire during 2005-2009 using MODerateresolution Imaging Spectro-radiometer (MODIS) sensor aboard the Terra and Aqua satellites, experimental data, and statistical data. The forest fire emission is estimated using equation established by Seiler and Crutzen in 1982. The spatial and temporal variation of forest fire emission is analyzed and displayed in the form of grid density map. From the satellite data analysis suggested between 2005 and 2009, the number of fire hotspots occurred 86,877 fire hotspots with a significant highest (more than 80% of fire hotspots) in the deciduous forest. The peak period of the forest fire is in January to May. The estimation on the emissions from forest fires during 2005 to 2009 indicated that the amount of CO, CO2, CH4, and N2O was about 3,133,845 tons, 47,610.337 tons, 204,905 tons, and 6,027 tons, respectively, or about 6,171,264 tons of CO2eq. They also emitted 256,132 tons of PM10. The year 2007 was found to be the year when the emissions were the largest. Annually, March is the period that has the maximum amount of forest fire emissions. The areas with high density of forest fire emission were the forests situated in the northern, the western, and the upper northeastern parts of the country.
Abstract: In recent years various types of electric vehicles
has gained again increasing attention as an environmentally
benign technology in transport. Especially for urban areas with
high local pollution this Zero-emission technology (at the point
of use) is considered to provide proper solutions. Yet, the bad
economics and the limited driving ranges are still major barriers
for a broader market penetration of battery electric vehicles
(BEV) and of fuel cell vehicles (FCV). The major result of our
analyses is that the most important precondition for a further
dissemination of BEV in urban areas are emission-free zones.
This is an instrument which allows the promotion of BEV
without providing excessive subsidies. In addition, it is
important to note that the full benefits of EV can only be
harvested if the electricity used is produced from renewable
energy sources. That is to say, it has to be ensured that the use of
BEV in urban areas is clearly linked to a green electricity
purchase model. And moreover, the introduction of a CO2-
emission-based tax system would support this requirement.
Abstract: The present study is aim to prepare and evaluate the selfnanoemulsifying drug delivery (SNEDDS) system of a poorly water soluble drug valsartan in order to achieve a better dissolution rate which would further help in enhancing oral bioavailability. The present research work describes a SNEDDS of valsartan using labrafil M 1944 CS, Tween 80 and Transcutol HP. The pseudoternary phase diagrams with presence and absence of drug were plotted to check for the emulsification range and also to evaluate the effect of valsartan on the emulsification behavior of the phases. The mixtures consisting of oil (labrafil M 1944 CS) with surfactant (tween 80), co-surfactant (Transcutol HP) were found to be optimum formulations. Prepared formulations were evaluated for its particle size distribution, nanoemulsifying properties, robustness to dilution, self emulsication time, turbidity measurement, drug content and invitro dissolution. The optimized formulations are further evaluated for heating cooling cycle, centrifugation studies, freeze thaw cycling, particle size distribution and zeta potential were carried out to confirm the stability of the formed SNEDDS formulations. The prepared formulation revealed t a significant improvement in terms of the drug solubility as compared with marketed tablet and pure drug.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: The phase diagrams and compositions of coexisting
phases have been determined for aqueous two-phase systems
containing poly(propylene glycol) with average molecular weight of
425 and sodium citrate at various pH of 3.93, 4.44, 4.6, 4.97, 5.1,
8.22. The effect of pH on the salting-out effect of poly (propylene
glycol) by sodium citrate has been studied. It was found that, an
increasing in pH caused the expansion of two-phase region.
Increasing pH also increases the concentration of PPG in the PPGrich
phase, while the salt-rich phase will be somewhat mole diluted.
Abstract: This paper uses quasi-steady molecular statics model
and diamond tool to carry out simulation temperature rise of nanoscale
orthogonal cutting single-crystal silicon. It further qualitatively
analyzes temperature field of silicon workpiece without considering
heat transfer and considering heat transfer. This paper supposes that
the temperature rise of workpiece is mainly caused by two heat sources:
plastic deformation heat and friction heat. Then, this paper develops a
theoretical model about production of the plastic deformation heat and
friction heat during nanoscale orthogonal cutting. After the increased
temperature produced by these two heat sources are added up, the
acquired total temperature rise at each atom of the workpiece is
substituted in heat transfer finite difference equation to carry out heat
transfer and calculates the temperature field in each step and makes
related analysis.
Abstract: In this work, grinding or microcutting tools in the form of pellets were manufactured using a bounded alumina abrasive grains. The bound used is a vitreous material containing quartz feldspars, kaolinite and a quantity of hematite. The pellets were used in glass grinding process to replace the free abrasive grains lapping process. The study of the elaborated pellets were done to define their effectiveness in the grinding process and to optimize the influence of the pellets elaboration parameters. The obtained results show the existence of an optimal combination of the pellets elaboration parameters for each glass grinding phase (coarse to fine grinding). The final roughness (rms) reached by the elaborated pellets on a BK7 glass surface was about 0.392 μm.
Abstract: Spectrum is a scarce commodity, and considering the spectrum scarcity faced by the wireless-based service providers led to high congestion levels. Technical inefficiencies from pooled, since all networks share a common pool of channels, exhausting the available channels will force networks to block the services. Researchers found that cognitive radio (CR) technology may resolve the spectrum scarcity. A CR is a self-configuring entity in a wireless networking that senses its environment, tracks changes, and frequently exchanges information with their networks. However, CRN facing challenges and condition become worst while tracks changes i.e. reallocation of another under-utilized channels while primary network user arrives. In this paper, channels or resource reallocation technique based on DNA-inspired computing algorithm for CRN has been proposed.