Abstract: Severe damages may occur during the drilling of carbon fiber reinforced plastics (CFRP). In practice, this damage is limited by adding a backup support to the drilled parts. For some aeronautical parts with curvatures, backing up parts is a demanding process. In order to simplify the operation, this research studies the effect of using a configurable setup to support parts on the resulting quality of drilled holes. The test coupons referenced in this study are twenty four-plies unidirectional laminates made of carbon fibers and epoxy resin. Different signals were measured during the drilling process for these laminates, including the thrust force, the displacement and the acceleration. The processing of these signals demonstrated that the damage is due to the combination of two main factors: the spring-back of the thin part and the thrust force. The results found were confirmed for different feeds and speeds. When the distance between supports is increased, it is observed that the spring-back increases but the thrust force decreases. The study proves the feasibility of unsupported drilling of thin CFRP laminates without creating any observable damage.
Abstract: Paleoclimate was reconstructed by the clay mineral
assemblages of shale units of Pabdeh (Paleocene- Oligocene), Gurpi
(Upper Cretaceous), Kazhdumi (Albian-Cenomanian) and Gadvan
(Aptian-Neocomian) formations in the Bangestan anticline. To
compare with clay minerals assemblages in these formations,
selected samples also taken from available formations in drilled wells
in Ahvaz, Marun, Karanj, and Parsi oil fields. Collected samples
prepared using standard clay mineral methodology. They were
treated as normal, glycolated and heated oriented glass slides. Their
identification was made on X-Ray diffractographs. Illite % varies
from 8 to 36. Illite quantity increased from Pabdeh to Gurpi
Formation. This may be due to dominant dry climate. Kaolinite is in
range of 12-49%. Its variation style in different formations could be a
marker of climate changes from wet to dry which is supported by the
lithological changes. Chlorite (4-28%) can also be detected in those
samples without any kaolinite. Mixed layer minerals as the mixture
of illite-chlorite and illite-vermiculite-montmorillonite are varied
from 6 to 36%, decreased during Kazhdumi deposition from the base
to the top. This result may be according to decreasing of illite
leaching process. Vermiculite was also determined in very less
quantity and found in those units without kaolinite. Montmorillonite
varies from 8 to 43%, and its presence is due to terrestrial
depositional condition. Stratigraphical documents is also supported
this idea that clay mineral distribution is a function of the climate
changes. It seems, thus, the present results can be indicated a possible
procedure for ancient climate changes evaluation.
Abstract: Among all microRNAs (miRNAs) in 12 plant species investigated in this study, only miR398 targeted the copper chaperone for superoxide dismutase (CCS). The nucleotide sequences of miRNA binding sites were located in the mRNA protein-coding sequence (CDS) and were highly homologous. These binding sites in CCS mRNA encoded a conservative GDLGTL hexapeptide. The binding sites for miR398 in the CDS of superoxide dismutase 1 mRNA encoded GDLGN pentapeptide. The conservative miR398 binding site located in the CDS of superoxide dismutase 2 mRNA encoded the GDLGNI hexapeptide. The miR398 binding site in the CDS of superoxide dismutase 3 mRNA encoded the GDLGNI or GDLGNV hexapeptide. Gene expression of the entire superoxide dismutase family in the studied plant species was regulated only by miR398. All members of the miR398 family, i.e. miR398a,b,c were connected to one site for each CuZnSOD and chaperone mRNA.
Abstract: OLAP uses multidimensional structures, to provide
access to data for analysis. Traditionally, OLAP operations are more
focused on retrieving data from a single data mart. An exception is
the drill across operator. This, however, is restricted to retrieving
facts on common dimensions of the multiple data marts. Our concern
is to define further operations while retrieving data from multiple
data marts. Towards this, we have defined six operations which
coalesce data marts. While doing so we consider the common as well
as the non-common dimensions of the data marts.
Abstract: The evolution of logic circuits, which falls under the heading of evolvable hardware, is carried out by evolutionary algorithms. These algorithms are able to automatically configure reconfigurable devices. One of main difficulties in developing evolvable hardware with the ability to design functional electrical circuits is to choose the most favourable EA features such as fitness function, chromosome representations, population size, genetic operators and individual selection. Until now several researchers from the evolvable hardware community have used and tuned these parameters and various rules on how to select the value of a particular parameter have been proposed. However, to date, no one has presented a study regarding the size of the chromosome representation (circuit layout) to be used as a platform for the evolution in order to increase the evolvability, reduce the number of generations and optimize the digital logic circuits through reducing the number of logic gates. In this paper this topic has been thoroughly investigated and the optimal parameters for these EA features have been proposed. The evolution of logic circuits has been carried out by an extrinsic evolvable hardware system which uses (1+λ) evolution strategy as the core of the evolution.
Abstract: In this paper, we combine a probabilistic neural method with radial-bias functions in order to construct the lithofacies of the wells DF01, DF02 and DF03 situated in the Triassic province of Algeria (Sahara). Lithofacies is a crucial problem in reservoir characterization. Our objective is to facilitate the experts' work in geological domain and to allow them to obtain quickly the structure and the nature of lands around the drilling. This study intends to design a tool that helps automatic deduction from numerical data. We used a probabilistic formalism to enhance the classification process initiated by a Self-Organized Map procedure. Our system gives lithofacies, from well-log data, of the concerned reservoir wells in an aspect easy to read by a geology expert who identifies the potential for oil production at a given source and so forms the basis for estimating the financial returns and economic benefits.
Abstract: The effect of plant growth-promoting rhizobacteria
(PGPR) on seed germination, seedling growth and yield of field
grown maize were evaluated in three experiments. In these
experiments six bacterial strains include P.putida strain R-168,
P.fluorescens strain R-93, P.fluorescens DSM 50090, P.putida
DSM291, A.lipoferum DSM 1691, A.brasilense DSM 1690 were
used. Results of first study showed seed Inoculation significantly
enhanced seed germination and seedling vigour of maize. In second
experiment, leaf and shoot dry weight and also leaf surface area
significantly were increased by bacterial inoculation in both sterile
and non-sterile soil. The results showed that inoculation with
bacterial treatments had a more stimulating effect on growth and
development of plants in nonsterile than sterile soil. In the third
experiment, Inoculation of maize seeds with all bacterial strains
significantly increased plant height, 100 seed weight, number of seed
per ear and leaf area .The results also showed significant increase in
ear and shoot dry weight of maize.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: MiRNAs participate in gene regulation of translation.
Some studies have investigated the interactions between genes and
intragenic miRNAs. It is important to study the miRNA binding sites
of genes involved in carcinogenesis. RNAHybrid 2.1 and ERNAhybrid
programmes were used to compute the hybridization free
energy of miRNA binding sites. Of these 54 mRNAs, 22.6%, 37.7%,
and 39.7% of miRNA binding sites were present in the 5'UTRs,
CDSs, and 3'UTRs, respectively. The density of the binding sites for
miRNAs in the 5'UTR ranged from 1.6 to 43.2 times and from 1.8 to
8.0 times greater than in the CDS and 3'UTR, respectively. Three
types of miRNA interactions with mRNAs have been revealed: 5'-
dominant canonical, 3'-compensatory, and complementary binding
sites. MiRNAs regulate gene expression, and information on the
interactions between miRNAs and mRNAs could be useful in
molecular medicine. We recommend that newly described sites
undergo validation by experimental investigation.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: Numerous experimental tests for post-installed anchor systems drilled in hardened concrete were conducted in order to estimate pull-out and shear strength accounting for uncertainties such as torque ratios, embedment depths and different diameters in demands. In this study, the strength of the systems was significantly changed by the effect of those three uncertainties during pull-out experimental tests, whereas the shear strength of the systems was not affected by torque ratios. It was also shown that concrete cone failure or damage mechanism was generally investigated during and after pull-out tests and in shear strength tests, mostly the anchor systems were failed prior to failure of primary structural system. Furthermore, 3D finite element model for the anchor systems was created by ABAQUS for the numerical analysis. The verification of finite element model was identical till the failure points to the load-displacement relationship specified by the experimental tests.
Abstract: For investigations of electromagnetic field
distributions in biological structures by Finite Element Method
(FEM), a method for automatic 3D model building of human
anatomical objects is developed. Models are made by meshed
structures and specific electromagnetic material properties for each
tissue type. Mesh is built according to specific FEM criteria for
achieving good solution accuracy. Several FEM models of
anatomical objects are built. Formulation using magnetic vector
potential and scalar electric potential (A-V, A) is used for modeling
of electromagnetic fields in human tissue objects. The developed
models are suitable for investigations of electromagnetic field
distributions in human tissues exposed in external fields during
magnetic stimulation, defibrillation, impedance tomography etc.
Abstract: This paper describes the architectural design
considerations for building a new class of application, a Personal
Knowledge Integrator and a particular example a Knowledge Theatre.
It then supports this description by describing a scenario of a child
acquiring knowledge and how this process could be augmented by
the proposed architecture and design of a Knowledge Theatre. David
Merrill-s first “principles of instruction" are kept in focus to provide
a background to view the learning potential.
Abstract: This paper deals with the application of a fuzzy set in
measuring teachers- beliefs about mathematics. The vagueness of
beliefs was transformed into standard mathematical values using a
fuzzy preferences model. The study employed a fuzzy approach
questionnaire which consists of six attributes for measuring
mathematics teachers- beliefs about mathematics. The fuzzy conjoint
analysis approach based on fuzzy set theory was used to analyze the
data from twenty three mathematics teachers from four secondary
schools in Terengganu, Malaysia. Teachers- beliefs were recorded in
form of degrees of similarity and its levels of agreement. The
attribute 'Drills and practice is one of the best ways of learning
mathematics' scored the highest degree of similarity at 0. 79860 with
level of 'strongly agree'. The results showed that the teachers- beliefs
about mathematics were varied. This is shown by different levels of
agreement and degrees of similarity of the measured attributes.
Abstract: Thermoplastic starch, polylactic acid glycerol and
maleic anhydride (MA) were compounded with natural
montmorillonite (MMT) through a twin screw extruder to investigate
the effects of different loading of MMT on structure, thermal and
absorption behavior of the nanocomposites. X-ray diffraction analysis
(XRD) showed that sample with MMT loading 4phr exhibited
exfoliated structure while sample that contained MMT 8 phr
exhibited intercalated structure. FESEM images showed big lump
when MMT loading was at 8 phr. The thermal properties were
characterized by using differential scanning calorimeter (DSC). The
results showed that MMT increased melting temperature and
crystallization temperature of matrix but reduction in glass transition
temperature was observed Meanwhile the addition of MMT has
improved the water barrier property. The nanosize MMT particle is
also able to block a tortuous pathway for water to enter the starch
chain, thus reducing the water uptake and improved the physical
barrier of nanocomposite.
Abstract: The purpose of the paper is to develop an informationcontrol environment for overall management and self-reconfiguration of the reconfigurable multifunctional machine tool for machining both rotation and prismatic parts and high concentration of different technological operations - turning, milling, drilling, grinding, etc. For the realization of this purpose on the basis of defined sub-processes for the implementation of the technological process, architecture of the information-search system for machine control is suggested. By using the object-oriented method, a structure and organization of the search system based on agents and manager with central control are developed. Thus conditions for identification of available information in DBs, self-reconfiguration of technological system and entire control of the reconfigurable multifunctional machine tool are created.
Abstract: Horizontal wells are proven to be better producers
because they can be extended for a long distance in the pay zone.
Engineers have the technical means to forecast the well productivity
for a given horizontal length. However, experiences have shown that
the actual production rate is often significantly less than that of
forecasted. It is a difficult task, if not impossible to identify the real
reason why a horizontal well is not producing what was forecasted.
Often the source of problem lies in the drilling of horizontal section
such as permeability reduction in the pay zone due to mud invasion
or snaky well patterns created during drilling. Although drillers aim
to drill a constant inclination hole in the pay zone, the more frequent
outcome is a sinusoidal wellbore trajectory. The two factors, which
play an important role in wellbore tortuosity, are the inclination and
side force at bit. A constant inclination horizontal well can only be
drilled if the bit face is maintained perpendicular to longitudinal axis
of bottom hole assembly (BHA) while keeping the side force nil at
the bit. This approach assumes that there exists no formation force at
bit. Hence, an appropriate BHA can be designed if bit side force and
bit tilt are determined accurately. The Artificial Neural Network
(ANN) is superior to existing analytical techniques. In this study, the
neural networks have been employed as a general approximation tool
for estimation of the bit side forces. A number of samples are
analyzed with ANN for parameters of bit side force and the results
are compared with exact analysis. Back Propagation Neural network
(BPN) is used to approximation of bit side forces. Resultant low
relative error value of the test indicates the usability of the BPN in
this area.
Abstract: Offset Double-Disk Opener (DDO) is a popular
furrow opener in conservation tillage. It has some limitations such as
negative suction to penetrate in the soil, hair pinning and mixing seed
and fertilizer in the slot. Because of importance of separation of seed
and fertilizer in the slot, by adding two horizontal mini disks to DDO
a modified opener was made (MDO) which placed the fertilizer
between and under two rows of seed. To consider performance of
novel opener an indoor comparison test between DDO and MDO was
performed at soil bin. The experiment was conducted with three
working speeds (3, 6 and 8 km h-1), two bulk densities of soil (1.1
and 1.4 Mg m-3) and two levels of residues (1 and 2 ton ha-1). The
experimental design consisted in a (3×2×2) complete randomized
factorial with three replicates for each test. Moisture of seed furrow,
separation of seed and fertilizer, hair pinning and resultant forces
acting on the openers were used as assessing indexes. There was no
significant difference between soil moisture content in slots created
by DDO and MDO at 0-4 cm depth, but at 4-8 cm the in the slot
created by MDO moisture content was higher about 9%. Horizontal
force for both openers increased with increasing speed and soil bulk
density. Vertical force for DDO was negative so it needed additional
weight for penetrating in the soil, but vertical force for MDO was
positive and, which can solve the challenge of penetration in the soil
in DDO. In soft soil with heavy residues some trash was pushed by
DDO into seed furrow (hair pinning) but at MDO seed were placed at
clean groove. Lateral and vertical separation of seed and fertilizer
was performed effectively by MDO (4.5 and 5 cm, respectively)
while DDO put seed and fertilizer close to each other. Overall, the
Modified Offset Double-disks (MDO) had better performance. So by
adapting this opener with no-tillage drillers it would possible to have
higher yield in conservation tillage where the most appropriate
opener is disk type.
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.
Abstract: Environmental micro-organisms include a large number of taxa and some species that are generally considered nonpathogenic, but can represent a risk in certain conditions, especially for elderly people and immunocompromised individuals. Chemotaxonomic identification techniques are powerful tools for environmental micro-organisms, and cellular fatty acid methyl esters (FAME) content is a powerful fingerprinting identification technique. A system based on an unsupervised artificial neural network (ANN) was set up using the fatty acid profiles of standard bacterial strains, obtained by gas-chromatography, used as learning data. We analysed 45 certified strains belonging to Acinetobacter, Aeromonas, Alcaligenes, Aquaspirillum, Arthrobacter, Bacillus, Brevundimonas, Enterobacter, Flavobacterium, Micrococcus, Pseudomonas, Serratia, Shewanella and Vibrio genera. A set of 79 bacteria isolated from a drinking water line (AMGA, the major water supply system in Genoa) were used as an example for identification compared to standard MIDI method. The resulting ANN output map was found to be a very powerful tool to identify these fresh isolates.