Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: This paper presents the study of parameters affecting
the environment protection in the printing industry. The paper has
also compared LCA studies performed within the printing industry in
order to identify common practices, limitations, areas for
improvement, and opportunities for standardization. This comparison
is focused on the data sources and methodologies used in the printing
pollutants register. The presented concepts, methodology and results
represent the contribution to the sustainable development
management. Furthermore, the paper analyzes the result of the
quantitative identification of hazardous substances emitted in printing
industry of Novi Sad.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: In this paper, creep constitutive equations of base
(Parent) and weld materials of the weldment for cold-drawn 304L
stainless steel have been obtained experimentally. For this purpose,
test samples have been generated from cold drawn bars and weld
material according to the ASTM standard. The creep behavior and
properties have been examined for these materials by conducting uniaxial
creep tests. Constant temperatures and constant load uni-axial
creep tests have been carried out at two high temperatures, 680 and
720 oC, subjected to constant loads, which produce initial stresses
ranging from 240 to 360 MPa. The experimental data have been used
to obtain the creep constitutive parameters using numerical
optimization techniques.
Abstract: The paper considers a single-server queue with fixedsize
batch Poisson arrivals and exponential service times, a model
that is useful for a buffer that accepts messages arriving as fixed size
batches of packets and releases them one packet at time. Transient
performance measures for queues have long been recognized as
being complementary to the steady-state analysis. The focus of the
paper is on the use of the functions that arise in the analysis of the
transient behaviour of the queuing system. The paper exploits
practical modelling to obtain a solution to the integral equation
encountered in the analysis. Results obtained indicate that under
heavy load conditions, there is significant disparity in the statistics
between the transient and steady state values.
Abstract: The epoxidation of soybean oil at temperature of 600C
was provided the best result in terms of attaching the –OH
functionality. Temperatures below and above 600C it is likely the
attaching reaction did not proceed sufficiently fast. The considerable
yield below 40%, implies the oil is not completely converted, it is not
possible by conventional methods, because the epoxide decomposes
at the temperature required. The objective of this work was the
development of catalyst toward the conversion of epoxide and polyol
with reaction temperature at 50,60, and 700C. The effect of different
type of catalyst were studied, the effect of alcohols with different
molecular configuration was determined which leads to selective
addition of alcohols to the epoxide oils.
Abstract: Complexity, as a theoretical background has made it
easier to understand and explain the features and dynamic behavior
of various complex systems. As the common theoretical background
has confirmed, borrowing the terminology for design from the
natural sciences has helped to control and understand urban
complexity. Phenomena like self-organization, evolution and
adaptation are appropriate to describe the formerly inaccessible
characteristics of the complex environment in unpredictable bottomup
systems. Increased computing capacity has been a key element in
capturing the chaotic nature of these systems.
A paradigm shift in urban planning and architectural design has
forced us to give up the illusion of total control in urban
environment, and consequently to seek for novel methods for
steering the development. New methods using dynamic modeling
have offered a real option for more thorough understanding of
complexity and urban processes. At best new approaches may renew
the design processes so that we get a better grip on the complex
world via more flexible processes, support urban environmental
diversity and respond to our needs beyond basic welfare by liberating
ourselves from the standardized minimalism.
A complex system and its features are as such beyond human
ethics. Self-organization or evolution is either good or bad. Their
mechanisms are by nature devoid of reason. They are common in
urban dynamics in both natural processes and gas. They are features
of a complex system, and they cannot be prevented. Yet their
dynamics can be studied and supported.
The paradigm of complexity and new design approaches has been
criticized for a lack of humanity and morality, but the ethical
implications of scientific or computational design processes have not
been much discussed. It is important to distinguish the (unexciting)
ethics of the theory and tools from the ethics of computer aided
processes based on ethical decisions. Urban planning and architecture
cannot be based on the survival of the fittest; however, the natural
dynamics of the system cannot be impeded on grounds of being
“non-human".
In this paper the ethical challenges of using the dynamic models
are contemplated in light of a few examples of new architecture and
dynamic urban models and literature. It is suggested that ethical
challenges in computational design processes could be reframed
under the concepts of responsibility and transparency.
Abstract: The segmentation of endovascular tools in fluoroscopy images can be accurately performed automatically or by minimum user intervention, using known modern techniques. It has been proven in literature, but no clinical implementation exists so far because the computational time requirements of such technology have not yet been met. A classical segmentation scheme is composed of edge enhancement filtering, line detection, and segmentation. A new method is presented that consists of a vector that propagates in the image to track an edge as it advances. The filtering is performed progressively in the projected path of the vector, whose orientation allows for oriented edge detection, and a minimal image area is globally filtered. Such an algorithm is rapidly computed and can be implemented in real-time applications. It was tested on medical fluoroscopy images from an endovascular cerebral intervention. Ex- periments showed that the 2D tracking was limited to guidewires without intersection crosspoints, while the 3D implementation was able to cope with such planar difficulties.
Abstract: Applicability of tuning the controller gains for Stewart manipulator using genetic algorithm as an efficient search technique is investigated. Kinematics and dynamics models were introduced in detail for simulation purpose. A PD task space control scheme was used. For demonstrating technique feasibility, a Stewart manipulator numerical-model was built. A genetic algorithm was then employed to search for optimal controller gains. The controller was tested onsite a generic circular mission. The simulation results show that the technique is highly convergent with superior performance operating for different payloads.
Abstract: The use of the oncologic index ISTER allows for a more effective planning of the radiotherapic facilities in the hospitals. Any change in the radiotherapy treatment, due to unexpected stops, may be adapted by recalculating the doses to the new treatment duration while keeping the optimal prognosis. The results obtained in a simulation model on millions of patients allow the definition of optimal success probability algorithms.
Abstract: Radio-frequency identification has entered as a beneficial means with conforming GS1 standards to provide the best solutions in the manufacturing area. It competes with other automated identification technologies e.g. barcodes and smart cards with regard to high speed scanning, reliability and accuracy as well. The purpose of this study is to improve production line-s performance by implementing RFID system in the manufacturing area on the basis of radio-frequency identification (RFID) system by 3D modeling in the program Cinema 4D R13 which provides obvious graphical scenes for users to portray their applications. Finally, with regard to improving system performance, it shows how RFID appears as a well-suited technology in a comparison of the barcode scanner to handle different kinds of raw materials in the production line base on logical process.
Abstract: The paper is devoted to stochastic analysis of finite
dimensional difference equation with dependent on ergodic Markov
chain increments, which are proportional to small parameter ". A
point-form solution of this difference equation may be represented
as vertexes of a time-dependent continuous broken line given on the
segment [0,1] with "-dependent scaling of intervals between vertexes.
Tending " to zero one may apply stochastic averaging and diffusion
approximation procedures and construct continuous approximation of
the initial stochastic iterations as an ordinary or stochastic Ito differential
equation. The paper proves that for sufficiently small " these
equations may be successfully applied not only to approximate finite
number of iterations but also for asymptotic analysis of iterations,
when number of iterations tends to infinity.
Abstract: In this paper stress and strain for two rotating thin
wall cylinder fitted together with initial interference and overlap are
computed. Also stress value for variation of initial interference is
calculated.
At first problem is considered without rotation and next angular
velocity increased from 0 to 50000 rev/min and stress in each stage
is calculated. The important point is that when stress become very
small in magnitude the angular velocity is critical and two cylinders
will separate. The critical speed i.e. speed of separation is calculated
in each step.
Abstract: The speech signal conveys information about the
identity of the speaker. The area of speaker identification is
concerned with extracting the identity of the person speaking the
utterance. As speech interaction with computers becomes more
pervasive in activities such as the telephone, financial transactions
and information retrieval from speech databases, the utility of
automatically identifying a speaker is based solely on vocal
characteristic. This paper emphasizes on text dependent speaker
identification, which deals with detecting a particular speaker from a
known population. The system prompts the user to provide speech
utterance. System identifies the user by comparing the codebook of
speech utterance with those of the stored in the database and lists,
which contain the most likely speakers, could have given that speech
utterance. The speech signal is recorded for N speakers further the
features are extracted. Feature extraction is done by means of LPC
coefficients, calculating AMDF, and DFT. The neural network is
trained by applying these features as input parameters. The features
are stored in templates for further comparison. The features for the
speaker who has to be identified are extracted and compared with the
stored templates using Back Propogation Algorithm. Here, the
trained network corresponds to the output; the input is the extracted
features of the speaker to be identified. The network does the weight
adjustment and the best match is found to identify the speaker. The
number of epochs required to get the target decides the network
performance.
Abstract: Primary barrier of membrane type LNG containment system consist of corrugated 304L stainless steel. This 304L stainless steel is austenitic stainless steel which shows different material behaviors owing to phase transformation during the plastic work. Even though corrugated primary barriers are subjected to significant amounts of pre-strain due to press working, quantitative mechanical behavior on the effect of pre-straining at cryogenic temperatures are not available. In this study, pre-strain level and pre-strain temperature dependent tensile tests are carried to investigate mechanical behaviors. Also, constitutive equations with material parameters are suggested for a verification study.
Abstract: In this paper, we propose an energy efficient cluster
based communication protocol for wireless sensor network. Our
protocol considers both the residual energy of sensor nodes and the
distance of each node from the BS when selecting cluster-head. This
protocol can successfully prolong the network-s lifetime by 1)
reducing the total energy dissipation on the network and 2) evenly
distributing energy consumption over all sensor nodes. In this
protocol, the nodes with more energy and less distance from the BS
are probable to be selected as cluster-head. Simulation results with
MATLAB show that proposed protocol could increase the lifetime of
network more than 94% for first node die (FND), and more than 6%
for the half of the nodes alive (HNA) factor as compared with
conventional protocols.
Abstract: Utilities use operating reserve for frequency regulation.To ensure that the operating frequency and system security are well maintained, the operating grid codes always specify that the reserve quantity and response rate should meet some prescribed levels. This paper proposes a methodology to evaluate system's contingency reserve for an isolated power network. With the presented algorithm to estimate system's frequency response characteristic, an online allocation of contingency reserve would be feasible to meet the grid codes for contingency operation. Test results from the simulated conditions, and from the actual operating data verify the merits of the proposed methodology to system's frequency control, and security.
Abstract: Multi-agent system approach has proven to be an effective and appropriate abstraction level to construct whole models of a diversity of biological problems, integrating aspects which can be found both in "micro" and "macro" approaches when modeling this type of phenomena. Taking into account these considerations, this paper presents the important computational characteristics to be gathered into a novel bioinformatics framework built upon a multiagent architecture. The version of the tool presented herein allows studying and exploring complex problems belonging principally to structural biology, such as protein folding. The bioinformatics framework is used as a virtual laboratory to explore a minimalist model of protein folding as a test case. In order to show the laboratory concept of the platform as well as its flexibility and adaptability, we studied the folding of two particular sequences, one of 45-mer and another of 64-mer, both described by an HP model (only hydrophobic and polar residues) and coarse grained 2D-square lattice. According to the discussion section of this piece of work, these two sequences were chosen as breaking points towards the platform, in order to determine the tools to be created or improved in such a way to overcome the needs of a particular computation and analysis of a given tough sequence. The backwards philosophy herein is that the continuous studying of sequences provides itself important points to be added into the platform, to any time improve its efficiency, as is demonstrated herein.
Abstract: Investment in a constructed facility represents a cost in
the short term that returns benefits only over the long term use of the
facility. Thus, the costs occur earlier than the benefits, and the owners
of facilities must obtain the capital resources to finance the costs of
construction. A project cannot proceed without an adequate
financing, and the cost of providing an adequate financing can be
quite large. For these reasons, the attention to the project finance is an
important aspect of project management. Finance is also a concern to
the other organizations involved in a project such as the general
contractor and material suppliers. Unless an owner immediately and
completely covers the costs incurred by each participant, these
organizations face financing problems of their own. At a more
general level, the project finance is the only one aspect of the general
problem of corporate finance. If numerous projects are considered
and financed together, then the net cash flow requirements constitute
the corporate financing problem for capital investment. Whether
project finance is performed at the project or at the corporate level
does not alter the basic financing problem .In this paper, we will first
consider facility financing from the owner's perspective, with due
consideration for its interaction with other organizations involved in a
project. Later, we discuss the problems of construction financing
which are crucial to the profitability and solvency of construction
contractors. The objective of this paper is to present the steps utilized
to determine the best combination of minimum project financing.
The proposed model considers financing; schedule and maximum net
area .The proposed model is called Project Financing and Schedule
Integration using Genetic Algorithms "PFSIGA". This model
intended to determine more steps (maximum net area) for any project
with a subproject. An illustrative example will demonstrate the
feature of this technique. The model verification and testing are put
into consideration.