Abstract: Testability modeling is a commonly used method in
testability design and analysis of system. A dependency matrix will be
obtained from testability modeling, and we will give a quantitative
evaluation about fault detection and isolation.
Based on the dependency matrix, we can obtain the diagnosis tree.
The tree provides the procedures of the fault detection and isolation.
But the dependency matrix usually includes built-in test (BIT) and
manual test in fact. BIT runs the test automatically and is not limited
by the procedures. The method above cannot give a more efficient
diagnosis and use the advantages of the BIT.
A Comprehensive method of fault detection and isolation is
proposed. This method combines the advantages of the BIT and
Manual test by splitting the matrix. The result of the case study shows
that the method is effective.
Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: In this article, the antibiogram and heavy metal
resistance profile of the bacteria isolated from total 34 studied
animals (Pelophylax ridibundus = 12; Mauremys rivulata = 14;
Natrix natrix = 8) captured around the Biga Stream, are described.
There was no database information on antibiogram and heavy metal
resistance profile of bacteria from these area’s amphibians and
reptiles.
A total of 200 bacteria were successfully isolated from cloaca and
oral samples of the aquatic amphibians and reptiles as well as from
the water sample. According to Jaccard’s similarity index, the degree
of similarity in the bacterial flora was quite high among the
amphibian and reptile species under examination, whereas it was
different from the bacterial diversity in the water sample. The most
frequent isolates were A. hydrophila (31.5%), B. pseudomallei
(8.5%), and C. freundii (7%). The total numbers of bacteria obtained
were as follows: 45 in P. ridibundus, 45 in N. natrix 30 in M.
rivulata, and 80 in the water sample. The result showed that
cefmetazole was the most effective antibiotic to control the bacteria
isolated in this study and that approximately 93.33% of the bacterial
isolates were sensitive to this antibiotic. The multiple antibiotic
resistances (MAR) index indicated that P. ridibundus (0.95) > N.
natrix (0.89) > M. rivulata (0.39). Furthermore, all the tested heavy
metals (Pb+2, Cu+2, Cr+3, and Mn+2) inhibit the growth of the bacterial
isolates at different rates. Therefore, it indicated that the water source
of the animals was contaminated with both antibiotic residues and
heavy metals.
Abstract: This paper provides a quantitative measure of the
time-varying multiunit neuronal spiking activity using an entropy
based approach. To verify the status embedded in the neuronal activity
of a population of neurons, the discrete wavelet transform (DWT) is
used to isolate the inherent spiking activity of MUA. Due to the
de-correlating property of DWT, the spiking activity would be
preserved while reducing the non-spiking component. By evaluating
the entropy of the wavelet coefficients of the de-noised MUA, a
multiresolution Shannon entropy (MRSE) of the MUA signal is
developed. The proposed entropy was tested in the analysis of both
simulated noisy MUA and actual MUA recorded from cortex in rodent
model. Simulation and experimental results demonstrate that the
dynamics of a population can be quantified by using the proposed
entropy.
Abstract: This paper presents a novel integrated hybrid
approach for fault diagnosis (FD) of nonlinear systems. Unlike most
FD techniques, the proposed solution simultaneously accomplishes
fault detection, isolation, and identification (FDII) within a unified
diagnostic module. At the core of this solution is a bank of adaptive
neural parameter estimators (NPE) associated with a set of singleparameter
fault models. The NPEs continuously estimate unknown
fault parameters (FP) that are indicators of faults in the system. Two
NPE structures including series-parallel and parallel are developed
with their exclusive set of desirable attributes. The parallel scheme is
extremely robust to measurement noise and possesses a simpler, yet
more solid, fault isolation logic. On the contrary, the series-parallel
scheme displays short FD delays and is robust to closed-loop system
transients due to changes in control commands. Finally, a fault
tolerant observer (FTO) is designed to extend the capability of the
NPEs to systems with partial-state measurement.
Abstract: This paper presents experimental investigation and
finite element analysis on buckling behavior of irregular section coldformed
steel columns under axially concentric loading. For the
experimental study, four different sections of columns were tested to
investigate effect of stiffening and width-to-thickness ratio on
buckling behavior. For each of the section, three lengths of 230, 950
and 1900 mm. were studied representing short, intermediate long and
long columns, respectively. Then, nonlinear finite element analyses
of the tested columns were performed. The comparisons in terms of
load-deformation response and buckling mode show good agreement
and hence the FEM models were validated. Parametric study of
stiffening element and thickness of 1.0, 1.15, 1.2, 1.5, 1.6 and 2.0
mm. was analyzed. The test results showed that stiffening effect pays
a large contribution to prevent distortional mode. The increase in wall
thickness enhanced buckling stress beyond the yielding strength in
short and intermediate columns, but not for the long columns.
Abstract: Taking into account the significance of measuring the
daily use of the study space in the libraries in order to develop and
reorganize the space for enhancing the efficiency of the study space,
the current study aimed to apply GIS in analyzing the study halls of
the Central Library and Document Center of Tehran University in
order to determine how study desks and chairs were used by the
students. The study used a combination of survey-descriptive and
system design method. In order to gather the required data, surveydescriptive
method was used. For implementing and entering data
into ArcGIS and analyzing the data and displaying the results on the
maps of the study halls of the library, system design method was
utilized. The design of the spatial database of the use of the study
halls was measured through the extent of occupancy of the space by
the library users and the maps of the study halls of the central library
of Tehran University as the case study. The results showed that
Abooreyhan hall had the highest rate of occupancy of the desks and
chairs compared to the other halls. The Hall of Science and
Technology, with an average occupancy rate of 0.39 for the tables
represented the lowest number of users and Rashid al-Dins hall, and
Science and Technology hall with an average occupancy rate (0.40)
had the lowest number of users for seats. In this study, the
comparison of the space occupied at different periods in the morning,
evenings, afternoons, and several months was performed through
GIS. This system analyzed the space relationships effectively and
efficiently. The output of this study would be used by administrators
and librarians to determine the exact extent of use of the equipment
of the study halls and librarians can use the output map to design the
space more efficiently at the library.
Abstract: The mechanisms underlying the association between
obesity and asthma may be related to a decreased immunological
tolerance induced by a defective function of regulatory T cells
(Tregs). The aim of this study is to establish the potential link
between these diseases and CD4+, CD25+ FoxP3+ Tregs as well as T
helper cells (Ths) in children. This is a prospective case control
study. Obese (n:40), asthmatic (n:40), asthmatic obese (n:40) and
healthy children (n:40), who don't have any acute or chronic diseases,
were included in this study. Obese children were evaluated according
to WHO criteria. Asthmatic patients were chosen based on GINA
criteria. Parents were asked to fill up the questionnaire. Informed
consent forms were taken. Blood samples were marked with CD4+,
CD25+ and FoxP3+ in order to determine Tregs and Ths by flow
cytometric method. Statistical analyses were performed. p≤0.05 was
chosen as meaningful threshold. Tregs exhibiting anti-inflammatory
nature were significantly lower in obese (0,16%; p≤0,001), asthmatic
(0,25%; p≤0,01) and asthmatic obese (0,29%; p≤0,05) groups than
the control group (0,38%). Ths were counted higher in asthma group
than the control (p≤0,01) and obese (p≤0,001) groups. T cell
immunity plays important roles in obesity and asthma pathogeneses.
Decreased numbers of Tregs found in obese, asthmatic and asthmatic
obese children may help to elucidate some questions in
pathophysiology of these diseases. For HOMA-IR levels, any
significant difference was not noted between control and obese
groups, but statistically higher values were found for obese
asthmatics. The values obtained in all groups were found to be below
the critical cut off points. This finding has made the statistically
significant difference observed between Tregs of obese, asthmatic,
obese asthmatic and control groups much more valuable. These
findings will be useful in diagnosis and treatment of these disorders
and future studies are needed. The production and propagation of
Tregs may be promising in alternative asthma and obesity treatments.
Abstract: This article focuses on upper-extremity musculoskeletal disorders risk assessment model at workplace. In this model are used risk factors that are responsible for musculoskeletal system damage. Based on statistic calculations the model is able to define what risk of MSD threatens workers who are under risk factors. The model is also able to say how MSD risk would decrease if these risk factors are eliminated.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: Phelipanche ramosa is the most damaging obligate
flowering parasitic weed on wide species of cultivated plants. The
semi-arid regions of the world are considered the main centers of this
parasitic plant that causes heavy infestation. This is due to its
production of high numbers of seeds (up to 200,000) that remain
viable for extended periods (up to 20 years). In this study, 13
treatments for the control of Phelipanche were carried out, which
included agronomic, chemical, and biological treatments and the use
of resistant plant methods. In 2014, a trial was performed at the
Department of Agriculture, Food and Environment, University of
Foggia (southern Italy), on processing tomato (cv ‘Docet’) grown in
pots filled with soil taken from a field that was heavily infested by P.
ramosa). The tomato seedlings were transplanted on May 8, 2014,
into a sandy-clay soil (USDA). A randomized block design with 3
replicates (pots) was adopted. During the growing cycle of the
tomato, at 70, 75, 81 and 88 days after transplantation, the number of
P. ramosa shoots emerged in each pot was determined. The tomato
fruit were harvested on August 8, 2014, and the quantitative and
qualitative parameters were determined. All of the data were
subjected to analysis of variance (ANOVA) using the JMP software
(SAS Institute Inc. Cary, NC, USA), and for comparisons of means
(Tukey's tests). The data show that each treatment studied did not
provide complete control against P. ramosa. However, the virulence
of the attacks was mitigated by some of the treatments tried: radicon
biostimulant, compost activated with Fusarium, mineral fertilizer
nitrogen, sulfur, enzone, and the resistant tomato genotype. It is
assumed that these effects can be improved by combining some of
these treatments with each other, especially for a gradual and
continuing reduction of the “seed bank” of the parasite in the soil.
Abstract: Fixed-geometry hydrodynamic journal bearings are
one of the best supporting systems for several applications of rotating
machinery. Cylindrical journal bearings present excellent loadcarrying
capacity and low manufacturing costs, but they are subjected
to the oil-film instability at high speeds. An attempt of overcoming
this instability problem has been the development of non-circular
journal bearings. This work deals with an analysis of oil-lubricated
elliptical journal bearings using the finite element method. Steadystate
and dynamic performance characteristics of elliptical bearings
are rendered by zeroth- and first-order lubrication equations obtained
through a linearized perturbation method applied on the classical
Reynolds equation. Four-node isoparametric rectangular finite
elements are employed to model the bearing thin film flow. Curves of
elliptical bearing load capacity and dynamic force coefficients are
rendered at several operating conditions. The results presented in this
work demonstrate the influence of the bearing ellipticity on its
performance at different loading conditions.
Abstract: In this paper, a direct power control (DPC)
strategies have been investigated in order to control a high
power AC/DC converter with time variable load. This converter
is composed of a three level three phase neutral point clamped
(NPC) converter as rectifier and an H-bridge four quadrant
current control converter. In the high power application,
controller not only must adjust the desire outputs but also
decrease the level of distortions which are injected to the network
from the converter. Regarding to this reason and nonlinearity
of the power electronic converter, the conventional controllers
cannot achieve appropriate responses. In this research, the
precise mathematical analysis has been employed to design the
appropriate controller in order to control the time variable
load. A DPC controller has been proposed and simulated using
Matlab/ Simulink. In order to verify the simulation result, a real
time simulator- OPAL-RT- has been employed. In this paper,
the dynamic response and stability of the high power NPC
with variable load has been investigated and compared with
conventional types using a real time simulator. The results proved
that the DPC controller is more stable and has more precise
outputs in comparison with conventional controller.
Abstract: This paper describes an Action Research project
which was undertaken to inform professional practice in order to
develop a newly created Centre for Student Success in the specific
context of transnational medical and nursing education in the Middle
East. The objectives were to enhance the academic performance,
persistence, integration and personal and professional development of
a multinational study body, in particular in relation to pre-clinical
medical students, and to establish a comfortable, friendly and
student-driven environment within an Irish medical university
recently established in Bahrain. The outcomes of the project resulted
in the development of a specific student success ‘signature’ for this
particular transnational higher education context.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: The effect of transition metal doping on Pt/Al2O3
catalyst used in propane dehydrogenation reaction at 500°C was
studied. The preparation methods investigated were sequential
impregnation (Pt followed by the 2nd metal or the 2nd metal followed
by Pt) and co-impregnation. The metal contents of these catalysts
were fixed as the weight ratio of Pt per the 2nd metal of around 0.075.
These catalysts were characterized by N2-physisorption, TPR, COchemisorption
and NH3-TPD. It was found that the impregnated 2nd
metal had an effect upon reducibility of Pt due to its interaction with
transition metal-containing structure. This was in agreement with the
CO-chemisorption result that the presence of Pt metal, which is a
result from Pt species reduction, was decreased. The total acidity of
bimetallic catalysts is decreased but the strong acidity is slightly
increased. It was found that the stability of bimetallic catalysts
prepared by co-impregnation and sequential impregnation where the
2nd metal was impregnated before Pt were better than that of
monometallic catalyst (undoped Pt one) due to the forming of Pt sites
located on the transition metal-oxide modified surface. Among all
preparation methods, the sequential impregnation method- having Pt
impregnated before the 2nd metal gave the worst stability because this
catalyst lacked the modified Pt sites and some fraction of Pt sites was
covered by the 2nd metal.
Abstract: The development of active and stable catalysts
without noble metals for low temperature oxidation of exhaust gases
remains a significant challenge. The purpose of this study is to
determine the influence of the preparation method on the catalytic
activity of the supported copper-manganese mixed oxides in terms of
VOCs oxidation. The catalysts were prepared by impregnation of γ-
Al2O3 with copper and manganese nitrates and acetates and the
possibilities for CO, CH3OH and dimethyl ether (DME) oxidation
were evaluated using continuous flow equipment with a four-channel
isothermal stainless steel reactor. Effect of the support, Cu/Mn mole
ratio, heat treatment of the precursor and active component loading
were investigated. Highly active alumina supported Cu-Mn catalysts
for CO and VOCs oxidation were synthesized. The effect of
preparation conditions on the activity behavior of the catalysts was
discussed.
The synergetic interaction between copper and manganese species
increases the activity for complete oxidation over mixed catalysts.
Type of support, calcination temperature and active component
loading along with catalyst composition are important factors,
determining catalytic activity. Cu/Mn molar ratio of 1:5, heat
treatment at 450oC and 20 % active component loading are the best
compromise for production of active catalyst for simultaneous
combustion of CO, CH3OH and DME.
Abstract: The formulated problem of optimization of the
technological process of water treatment for thermal power plants is
considered in this article. The problem is of multiparametric nature.
To optimize the process, namely, reduce the amount of waste water, a
new technology was developed to reuse such water. A mathematical
model of the technology of wastewater reuse was developed.
Optimization parameters were determined. The model consists of a
material balance equation, an equation describing the kinetics of ion
exchange for the non-equilibrium case and an equation for the ion
exchange isotherm. The material balance equation includes a
nonlinear term that depends on the kinetics of ion exchange. A direct
problem of calculating the impurity concentration at the outlet of the
water treatment plant was numerically solved. The direct problem
was approximated by an implicit point-to-point computation
difference scheme. The inverse problem was formulated as relates to
determination of the parameters of the mathematical model of the
water treatment plant operating in non-equilibrium conditions. The
formulated inverse problem was solved. Following the results of
calculation the time of start of the filter regeneration process was
determined, as well as the period of regeneration process and the
amount of regeneration and wash water. Multi-parameter
optimization of water treatment process for thermal power plants
allowed decreasing the amount of wastewater by 15%.
Abstract: This paper argues nation-building theories that
prioritize democratic governance best explain the successful postindependence
development of Botswana. Three main competing
schools of thought exist regarding the sequencing of policies that
should occur to re-build weakened or failed states. The first posits
that economic development should receive foremost attention, while
democratization and a binding sense of nationalism can wait. A
second group of experts identified constructing a sense of nationalism
among a populace is necessary first, so that the state receives popular
legitimacy and obedience that are prerequisites for development.
Botswana, though, transitioned into a multi-party democracy and
prosperous open economy due to the utilization of traditional
democratic structures, enlightened and accountable leadership, and an
educated technocratic civil service. With these political foundations
already in place when the discovery of diamonds occurred, the
resulting revenues were spent wisely on projects that grew the
economy, improved basic living standards, and attracted foreign
investment. Thus democratization preceded, and therefore provided
an accountable basis for, economic development that might otherwise
have been squandered by greedy and isolated elites to the detriment
of the greater population. Botswana was one of the poorest nations in
the world at the time of its independence in 1966, with little
infrastructure, a dependence on apartheid South Africa for trade, and
a largely subsistence economy. Over the next thirty years, though, its
economy grew the fastest of any nation in the world. The transparent
and judicious use of diamond returns is only a partial explanation, as
the government also pursued economic diversification, mass
education, and rural development in response to public needs.
As nation-building has become a project undertaken by nations
and multilateral agencies such as the United Nations and the North
Atlantic Treaty Organization, Botswana may provide best practices
that others should follow in attempting to reconstruct economically
and politically unstable states.