Abstract: This paper presents a ray tracing simulation technique for characterize the radiowave propagation inside building. The implementation of an algorithm capable of enumerating a large number of propagation paths in interactive time for the special case of 2.5D. The effective dielectric constants of the building structure in the simulations are indicated. The study describes an efficient 2.5D model of ray tracing algorithm were compared with 3D model. The result of the first investigations is that the environment of the indoor wave significantly changes as we change the electric parameters of material constructions. A detailed analysis of the dependence of the indoor wave on the wideband characteristics of the channel: root mean square (RMS) delay spread characteristics and Mean excess delay, is also investigated.
Abstract: Nowadays, the performance required for concrete
structures is more complicated and diversified. Self-compacting
concrete is a fluid mixture suitable for placing in structures with
congested reinforcement without vibration. Self-compacting concrete
development must ensure a good balance between deformability and
stability. Also, compatibility is affected by the characteristics of
materials and the mix proportions; it becomes necessary to evolve a
procedure for mix design of SCC.
This paper presents an experimental procedure for the design of
self-compacting concrete mixes with different water-cement ratios
(w/c) and other constant ratios by local materials. The test results for
acceptance characteristics of self-compacting concrete such as slump
flow, V-funnel and L-Box are presented. Further, compressive
strength, tensile strength and modulus of elasticity of specimens were
also determined and results are included here
Abstract: the cursive nature of the Arabic writing makes it
difficult to accurately segment characters or even deal with the whole
word efficiently. Therefore, in this paper, a printed Arabic sub-word
recognition system is proposed. The suggested algorithm utilizes
geometrical moments as descriptors for the separated sub-words.
Three types of moments are investigated and applied to the printed
sub-word images after dividing each image into multiple parts using
windowing. Since moments are global descriptors, the windowing
mechanism allows the moments to be applied to local regions of the
sub-word. The local-global mixture of the proposed scheme increases
the discrimination power of the moments while keeping the
simplicity and ease of use of moments.
Abstract: The coverage probability and range of IEEE 802.16
systems depend on different wireless scenarios. Evaluating the
performance of IEEE 802.16 systems over Stanford University
Interim (SUI) channels is suggested by IEEE 802.16 specifications.
In order to derive an effective method for forecasting the coverage
probability and range, this study uses the SUI channel model to
analyze the coverage probability with Rayleigh fading for an IEEE
802.16 system. The BER of the IEEE 802.16 system is shown in the
simulation results. Then, the maximum allowed path loss can be
calculated and substituted into the coverage analysis. Therefore,
simulation results show the coverage range with and without
Rayleigh fading.
Abstract: Routing security is a major concerned in Wireless
Sensor Network since a large scale of unattended nodes is deployed
in ad hoc fashion with no possibility of a global addressing due to a
limitation of node-s memory and the node have to be self organizing
when the systems require a connection with the other nodes. It
becomes more challenging when the nodes have to act as the router
and tightly constrained on energy and computational capabilities
where any existing security mechanisms are not allowed to be fitted
directly. These reasons thus increasing vulnerabilities to the network
layer particularly and to the whole network, generally. In this paper,
a Dynamic Window Secured Implicit Geographic Forwarding
(DWSIGF) routing is presented where a dynamic time is used for
collection window to collect Clear to Send (CTS) control packet in
order to find an appropriate hoping node. The DWIGF is expected to
minimize a chance to select an attacker as the hoping node that
caused by a blackhole attack that happen because of the CTS rushing
attack, which promise a good network performance with high packet
delivery ratios.
Abstract: Virtually all existing networked system management
tools use a Manager/Agent paradigm. That is, distributed agents are
deployed on managed devices to collect local information and report
it back to some management unit. Even those that use standard
protocols such as SNMP fall into this model. Using standard protocol
has the advantage of interoperability among devices from different
vendors. However, it may not be able to provide customized
information that is of interest to satisfy specific management needs.
In this dissertation work, different approaches are used to
collect information regarding the devices attached to a Local Area
Network. An SNMP aware application is being developed that will
manage the discovery procedure and will be used as data collector.
Abstract: Currently, there is no database or local norms for the
physical performance of Malaysian rugby players. This database or
norms are vital for Malaysian-s sports development as programs can
be setup to improve the current status. This pilot study was
conducted to evaluate the status of our semi professional rugby
players. The rugby players were randomly selected from the
Malaysian National team and several clubs in the Klang valley, Kuala
Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years)
were selected for this pilot study. Height, bodyweight, percentage
body fat and body mass index (BMI) and several other physical tests
were performed. Results from the BLEEP test revealed an average of
level 9, shuttle 2 for the players. Interestingly, forwards were taller,
heavier, and had lower maximal aerobic power than backs in the
same team. In conclusion, the physical characteristics of the rugby
players were much lower when compared to international players
from other countries. From this pilot study, the physical performance
of the Malaysian team must be improved in order to further develop
the sports.
Abstract: Considering today-s increasing speed of change,
radical and innovative improvement - Kaikaku, is a necessity parallel
to continuous incremental improvement - Kaizen, especially for
SME-s in order to attain the competitive edge needed to be profitable.
During 2011, a qualitative single case study with the objective of
realizing a kaikaku in production has been conducted. The case study
was run as a one year project using a collaborative approach
including both researchers and company representatives. The case
study was conducted with the purpose of gaining further knowledge
about kaikaku realization as well as its implications. The empirical
results provide insights about the great productivity results achieved
by applying a specific kaikaku realization approach. However, it also
sheds light on the difficulty and contradiction of combining
innovation management and production system development.
Abstract: Along with the basic features of students\' culture
information, with its widely usage oriented on implementation of the
new information technologies in educational process that determines
the search for ways of pointing to the similarity of interdisciplinary
connections content, aims and objectives of the study. In this regard,
the article questions about students\' information culture, and also
presented information about the aims and objectives of the
information culture process among students. In the formation of a
professional interest in relevant information, which is an opportunity
to assist in informing the professional activities of the essence of
effective use of interactive methods and innovative technologies in
the learning process. The result of the experiment proves the
effectiveness of the information culture process of students in
training the system of higher education based on the credit
technology. The main purpose of this paper is a comprehensive
review of students\' information culture.
Abstract: Free and open source software is gaining popularity at
an unprecedented rate of growth. Organizations despite some
concerns about the quality have been using them for various
purposes. One of the biggest concerns about free and open source
software is post release software defects and their fixing. Many
believe that there is no appropriate support available to fix the bugs.
On the contrary some believe that due to the active involvement of
internet user in online forums, they become a major source of
communicating the identification and fixing of defects in open source
software. The research model of this empirical investigation
establishes and studies the relationship between open source software
defects and online public forums. The results of this empirical study
provide evidence about the realities of software defects myths of
open source software. We used a dataset consist of 616 open source
software projects covering a broad range of categories to study the
research model of this investigation. The results of this investigation
show that online forums play a significant role identifying and fixing
the defects in open source software.
Abstract: Hydrogenated biodiesel is one of the most promising
renewable fuels. It has many advantages over conventional biodiesel,
including higher cetane number, higher heating value, lower
viscosity, and lower corrosiveness due to its absence of oxygen.
From previous work, Pd/TiO2 gave high conversion and selectivity in
hydrogenated biodiesel. In this work, the effect of biomass feedstocks
(i.e. beef fat, chicken fat, pork fat, and jatropha oil) on the production
of hydrogenated biodiesel over Pd/TiO2 has been studied. Biomass
feedstocks were analyzed by ICP-OES (inductively coupled plasma
optical emission spectrometry) to identify the content of impurities
(i.e. P, K, Ca, Na, and Mg). The deoxygenation catalyst, Pd/TiO2,
was prepared by incipient wetness impregnation (IWI) and tested in a
continuous flow packed-bed reactor at 500 psig, 325°C, H2/feed
molar ratio of 30, and LHSV of 4 h-1 for its catalytic activity and
selectivity in hydrodeoxygenation. All feedstocks gave high
selectivity in diesel specification range hydrocarbons and the main
hydrocarbons were n-pentadecane (n-C15) and n-heptadecane (n-
C17), resulting from the decarbonylation/decarboxylation reaction.
Intermediates such as oleic acid, stearic acid, palmitic acid, and esters
were also detected in minor amount. The conversion of triglycerides
in jatropha oil is higher than those of chicken fat, pork fat, and beef
fat, respectively. The higher concentration of metal impurities in
feedstock, the lower conversion of feedstock.
Abstract: Buckling-Restrained Braced Frame system(BRBFs)
are a new type of steel seismic-load-resisting system that has found
use in several countries because of its efficiency and its promise of
seismic performance far superior to that of conventional braced
frames. The system is addressed in the 2005 edition of the AISC
Seismic Provisions for Structural Steel Buildings, also a set of design
provisions has been developed by NEHRP. This report illustrates the
seismic design of buckling restrained braced frames and compares
the result of design in the application of earthquake load for ordinary
bracing systems and buckling restrained bracing systems to see the
advantage and disadvantages of this new type of seismic resisting
system in comparison with the old Ordinary Concentric Braced
Frame systems (OCBFs); they are defined by the provisions
governing their design.
Abstract: Microarray experiments are information rich; however, extensive data mining is required to identify the patterns that characterize the underlying mechanisms of action. For biologists, a key aim when analyzing microarray data is to group genes based on the temporal patterns of their expression levels. In this paper, we used an iterative clustering method to find temporal patterns of gene expression. We evaluated the performance of this method by applying it to real sporulation data and simulated data. The patterns obtained using the iterative clustering were found to be superior to those obtained using existing clustering algorithms.
Abstract: The selective recovery of heavy metals of Cu, Zn, Ni and Cr from a mixed plating sludge by sulfidation and oxidation treatment was targeted in this study. At first, the mixed plating sludge was simultaneously subjected to an extraction and Cu sulfidation process at pH=1.5 to dissolve heavy metals and to precipitate Cu2+ as CuS. In the next step, the sulfidation treatment of Zn was carried out at pH=4.5 and the residual solution was subjected to an oxidation treatment of chromium with H2O2 at pH=10.0. After the experiments, the selectivity of metal precipitation and the chromium oxidation ratio were evaluated. As results, it was found that the filter cake obtained after selective sulfidation of Cu was composed of 96.6% of Cu (100% equals to the sum of Cu, Zn, Ni and Cr contents). Such findings confirmed that almost complete extraction of heavy metals was achieved at pH=1.5 and also that Cu could be selectively recovered as CuS. Further, the filter cake obtained at pH=4.5 was composed of 91.5% Zn and 6.83% of Cr. Regarding the chromium oxidation step, the chromium oxidation ratio was found to increase with temperature and the addition of oxidation agent of H2O2, but only oxidation ratio of 59% was achieved at a temperature of 60°C and H2O2 to Cr3+ equivalent ratio of 180.
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: The unsteady wake of an EPPLER 361 airfoil in
pitching motion has been investigated in a subsonic wind tunnel by
hot-wire anemometry. The airfoil was given the pitching motion
about the one-quarter chord axis at reduced frequency of 0182.
Streamwise mean velocity profiles (wake profiles) were investigated
at several vertically aligned points behind the airfoil at one-quarter
chord downstream distance from trailing edge. Oscillation amplitude
and mean angle of attack were varied to determine the effects on
wake profiles. When the maximum dynamic angle of attack was
below the static stall angle of attack, weak effects on wake were
found by increasing oscillation amplitude and mean angle of attack.
But, for higher angles of attack strong unsteady effects were
appeared on the wake.
Abstract: The theoretical prediction of the acoustical
polarization effects in the heterogeneous composites, made of thick
elastic solids with thin nematic films, is presented. The numericalanalytical
solution to the problem of the different wave propagation
exhibits some new physical effects in the low frequency domain: the
appearance of the critical frequency and the existence of the narrow
transition zone where the wave rapidly changes its speed. The
associated wave attenuation is highly perturbed in this zone. We also
show the possible appearance of the critical frequencies where the
attenuation changes the sign. The numerical results of parametrical
analysis are presented and discussed.
Abstract: Wrist pulse analysis for identification of health status
is found in Ancient Indian as well as Chinese literature. The preprocessing
of wrist pulse is necessary to remove outlier pulses and
fluctuations prior to the analysis of pulse pressure signal. This paper
discusses the identification of irregular pulses present in the pulse
series and intricacies associated with the extraction of time domain
pulse features. An approach of Dynamic Time Warping (DTW) has
been utilized for the identification of outlier pulses in the wrist pulse
series. The ambiguity present in the identification of pulse features is
resolved with the help of first derivative of Ensemble Average of
wrist pulse series. An algorithm for detecting tidal and dicrotic notch
in individual wrist pulse segment is proposed.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: In this study, three subtypes of influenza A viruses (pH1N1, H5N1 and H3N2) which naturally infected human were analyzed by bioinformatic approaches to find candidate human cellular miRNAs targeting viral genomes. There were 76 miRNAs targeting influenza A viruses. Among these candidates, 70 miRNAs were subtypes specifically targeting each subtype of influenza A virus including 21 miRNAs targeted subtype H1N1, 27 miRNAs targeted subtype H5N1 and 22 miRNAs targeted subtype H3N2. The remaining 6 miRNAs target on multiple subtypes of influenza A viruses. Uniquely, hsa-miR-3145 is the only one candidate miRNA targeting PB1 gene of all three subtypes. Obviously, most of the candidate miRNAs are targeting on polymerase complex genes (PB2, PB1 and PA) of influenza A viruses. This study predicted potential human miRNAs targeting on different subtypes of influenza A viruses which might be useful for inhibition of viral replication and for better understanding of the interaction between virus and host cell.