Abstract: In this study the mixed convection heat transfer in a
coil-in-shell heat exchanger for various Reynolds numbers and
various dimensionless coil pitch was experimentally investigated.
The experiments were conducted for both laminar and turbulent flow
inside coil and the effects of coil pitch on shell-side heat transfer
coefficient of the heat exchanger were studied. The particular
difference in this study in comparison with the other similar studies
was the boundary conditions for the helical coils. The results indicate
that with the increase of coil pitch, shell-side heat transfer coefficient
is increased.
Abstract: In this paper, we have compared the performance of a Turbo and Trellis coded optical code division multiple access (OCDMA) system. The comparison of the two codes has been accomplished by employing optical orthogonal codes (OOCs). The Bit Error Rate (BER) performances have been compared by varying the code weights of address codes employed by the system. We have considered the effects of optical multiple access interference (OMAI), thermal noise and avalanche photodiode (APD) detector noise. Analysis has been carried out for the system with and without double optical hard limiter (DHL). From the simulation results it is observed that a better and distinct comparison can be drawn between the performance of Trellis and Turbo coded systems, at lower code weights of optical orthogonal codes for a fixed number of users. The BER performance of the Turbo coded system is found to be better than the Trellis coded system for all code weights that have been considered for the simulation. Nevertheless, the Trellis coded OCDMA system is found to be better than the uncoded OCDMA system. Trellis coded OCDMA can be used in systems where decoding time has to be kept low, bandwidth is limited and high reliability is not a crucial factor as in local area networks. Also the system hardware is less complex in comparison to the Turbo coded system. Trellis coded OCDMA system can be used without significant modification of the existing chipsets. Turbo-coded OCDMA can however be employed in systems where high reliability is needed and bandwidth is not a limiting factor.
Abstract: Proteomics is one of the largest areas of research for
bioinformatics and medical science. An ambitious goal of proteomics
is to elucidate the structure, interactions and functions of all proteins
within cells and organisms. Predicting Protein-Protein Interaction
(PPI) is one of the crucial and decisive problems in current research.
Genomic data offer a great opportunity and at the same time a lot of
challenges for the identification of these interactions. Many methods
have already been proposed in this regard. In case of in-silico
identification, most of the methods require both positive and negative
examples of protein interaction and the perfection of these examples
are very much crucial for the final prediction accuracy. Positive
examples are relatively easy to obtain from well known databases. But
the generation of negative examples is not a trivial task. Current PPI
identification methods generate negative examples based on some
assumptions, which are likely to affect their prediction accuracy.
Hence, if more reliable negative examples are used, the PPI prediction
methods may achieve even more accuracy. Focusing on this issue, a
graph based negative example generation method is proposed, which
is simple and more accurate than the existing approaches. An
interaction graph of the protein sequences is created. The basic
assumption is that the longer the shortest path between two
protein-sequences in the interaction graph, the less is the possibility of
their interaction. A well established PPI detection algorithm is
employed with our negative examples and in most cases it increases
the accuracy more than 10% in comparison with the negative pair
selection method in that paper.
Abstract: In this paper, Optimum adaptive loading algorithms
are applied to multicarrier system with Space-Time Block Coding
(STBC) scheme associated with space-time processing based on
singular-value decomposition (SVD) of the channel matrix over
Rayleigh fading channels. SVD method has been employed in
MIMO-OFDM system in order to overcome subchannel interference.
Chaw-s and Compello-s algorithms have been implemented to obtain
a bit and power allocation for each subcarrier assuming instantaneous
channel knowledge. The adaptive loaded SVD-STBC scheme is
capable of providing both full-rate and full-diversity for any number
of transmit antennas. The effectiveness of these techniques has
demonstrated through the simulation of an Adaptive loaded SVDSTBC
system, and the comparison shown that the proposed
algorithms ensure better performance in the case of MIMO.
Abstract: This paper introduces a new method called ARPDC (Advanced Robust Parallel Distributed Compensation) for automatic control of nonlinear systems. This method improves a quality of robust control by interpolating of robust and optimal controller. The weight of each controller is determined by an original criteria function for model validity and disturbance appreciation. ARPDC method is based on nonlinear Takagi-Sugeno (T-S) fuzzy systems and Parallel Distributed Compensation (PDC) control scheme. The relaxed stability conditions of ARPDC control of nominal system have been derived. The advantages of presented method are demonstrated on the inverse pendulum benchmark problem. From comparison between three different controllers (robust, optimal and ARPDC) follows, that ARPDC control is almost optimal with the robustness close to the robust controller. The results indicate that ARPDC algorithm can be a good alternative not only for a robust control, but in some cases also to an adaptive control of nonlinear systems.
Abstract: Composite steel-concrete slabs using thin-walled
corrugated steel sheets with embossments represent a modern and
effective combination of steel and concrete. However, the design
of new types of sheeting is conditional on the execution of expensive
and time-consuming laboratory testing. The effort to develop
a cheaper and faster method has lead to many investigations all over
the world. In our paper we compare the results from our experiments
involving vacuum loading, four-point bending and small-scale shear
tests.
Abstract: The objective of the research is to study and compare
response surface designs: Central composite designs (CCD), Box-
Behnken designs (BBD), Small composite designs (SCD), Hybrid
designs, and Uniform shell designs (USD) over sets of reduced models
when the design is in a spherical region for 3 and 4 design variables.
The two optimality criteria ( D and G ) are considered which larger
values imply a better design. The comparison of design optimality
criteria of the response surface designs across the full second order
model and sets of reduced models for 3 and 4 factors based on the
two criteria are presented.
Abstract: This paper presents the comparison study of current control techniques for shunt active power filter. The hysteresis current control, the delta modulation control and the carrier-based PWM control are considered in the paper. The synchronous detection method is used to calculate the reference currents for shunt active power filter. The simulation results show that the carrier-based PWM control technique provides the minimum %THD value of the source currents compared with other comparable techniques after compensation. However, the %THD values of all three techniques can follow the IEEE std.519-1992.
Abstract: Next Generation Wireless Network (NGWN) is
expected to be a heterogeneous network which integrates all different
Radio Access Technologies (RATs) through a common platform. A
major challenge is how to allocate users to the most suitable RAT for
them. An optimized solution can lead to maximize the efficient use
of radio resources, achieve better performance for service providers
and provide Quality of Service (QoS) with low costs to users.
Currently, Radio Resource Management (RRM) is implemented
efficiently for the RAT that it was developed. However, it is not
suitable for a heterogeneous network. Common RRM (CRRM) was
proposed to manage radio resource utilization in the heterogeneous
network. This paper presents a user level Markov model for a three
co-located RAT networks. The load-balancing based and service
based CRRM algorithms have been studied using the presented
Markov model. A comparison for the performance of load-balancing
based and service based CRRM algorithms is studied in terms of
traffic distribution, new call blocking probability, vertical handover
(VHO) call dropping probability and throughput.
Abstract: This paper presents the experimental as well as the
simulated performance studies on the transcritical CO2 heat pumps
for simultaneous water cooling and heating; effects of water mass
flow rates and water inlet temperatures of both evaporator and gas
cooler on the cooling and heating capacities, system COP and water
outlets temperatures are investigated. Study shows that both the
water mass flow rate and inlet temperature have significant effect on
system performances. Test results show that the effect of evaporator
water mass flow rate on the system performances and water outlet
temperatures is more pronounced (COP increases 0.6 for 1 kg/min)
compared to the gas cooler water mass flow rate (COP increases 0.4
for 1 kg/min) and the effect of gas cooler water inlet temperature is
more significant (COP decreases 0.48 for given ranges) compared to
the evaporator water inlet temperature (COP increases 0.43 for given
ranges). Comparisons of experimental values with simulated results
show the maximum deviation of 5% for cooling capacity, 10% for
heating capacity, 16% for system COP. This study offers useful
guidelines for selecting appropriate water mass flow rate to obtain
required system performance.
Abstract: The acoustic and articulatory properties of fricative speech sounds are being studied using magnetic resonance imaging (MRI) and acoustic recordings from a single subject. Area functions were derived from a complete set of axial and coronal MR slices using two different methods: the Mermelstein technique and the Blum transform. Area functions derived from the two techniques were shown to differ significantly in some cases. Such differences will lead to different acoustic predictions and it is important to know which is the more accurate. The vocal tract acoustic transfer function (VTTF) was derived from these area functions for each fricative and compared with measured speech signals for the same fricative and same subject. The VTTFs for /f/ in two vowel contexts and the corresponding acoustic spectra are derived here; the Blum transform appears to show a better match between prediction and measurement than the Mermelstein technique.
Abstract: This paper studies the effect of different compression
constraints and schemes presented in a new and flexible paradigm to
achieve high compression ratios and acceptable signal to noise ratios
of Arabic speech signals. Compression parameters are computed for
variable frame sizes of a level 5 to 7 Discrete Wavelet Transform
(DWT) representation of the signals for different analyzing mother
wavelet functions. Results are obtained and compared for Global
threshold and level dependent threshold techniques. The results
obtained also include comparisons with Signal to Noise Ratios, Peak
Signal to Noise Ratios and Normalized Root Mean Square Error.
Abstract: Key management is a vital component in any modern security protocol. Due to scalability and practical implementation considerations automatic key management seems a natural choice in significantly large virtual private networks (VPNs). In this context IETF Internet Key Exchange (IKE) is the most promising protocol under permanent review. We have made a humble effort to pinpoint IKEv2 net gain over IKEv1 due to recent modifications in its original structure, along with a brief overview of salient improvements between the two versions. We have used US National Institute of Technology NIIST VPN simulator to get some comparisons of important performance metrics.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: Since dealing with high dimensional data is
computationally complex and sometimes even intractable, recently
several feature reductions methods have been developed to reduce
the dimensionality of the data in order to simplify the calculation
analysis in various applications such as text categorization, signal
processing, image retrieval, gene expressions and etc. Among feature
reduction techniques, feature selection is one the most popular
methods due to the preservation of the original features.
In this paper, we propose a new unsupervised feature selection
method which will remove redundant features from the original
feature space by the use of probability density functions of various
features. To show the effectiveness of the proposed method, popular
feature selection methods have been implemented and compared.
Experimental results on the several datasets derived from UCI
repository database, illustrate the effectiveness of our proposed
methods in comparison with the other compared methods in terms of
both classification accuracy and the number of selected features.
Abstract: The development of Artificial Neural Networks
(ANNs) is usually a slow process in which the human expert has to
test several architectures until he finds the one that achieves best
results to solve a certain problem. This work presents a new
technique that uses Genetic Programming (GP) for automatically
generating ANNs. To do this, the GP algorithm had to be changed in
order to work with graph structures, so ANNs can be developed. This
technique also allows the obtaining of simplified networks that solve
the problem with a small group of neurons. In order to measure the
performance of the system and to compare the results with other
ANN development methods by means of Evolutionary Computation
(EC) techniques, several tests were performed with problems based
on some of the most used test databases. The results of those
comparisons show that the system achieves good results comparable
with the already existing techniques and, in most of the cases, they
worked better than those techniques.
Abstract: A product development for green logistics model using
the fuzzy analytic network process method is presented for evaluating
the relationships among the product design, the manufacturing
activities, and the green supply chain. In the product development
stage, there can be alternative ways to design the detailed components
to satisfy the design concept and product requirement. In different
design alternative cases, the manufacturing activities can be different.
In addition, the manufacturing activities can affect the green supply
chain of the components and product. In this research, a fuzzy analytic
network process evaluation model is presented for evaluating the
criteria in product design, manufacturing activities, and green supply
chain. The comparison matrices for evaluating the criteria among the
three groups are established. The total relational values between the
three groups represent the relationships and effects. In application, the
total relational values can be used to evaluate the design alternative
cases for decision-making to select a suitable design case and the green
supply chain. In this presentation, an example product is illustrated. It
shows that the model is useful for integrated evaluation of design and
manufacturing and green supply chain for the purpose of product
development for green logistics.
Abstract: This paper presents an alternate approach that uses
artificial neural network to simulate the flood level dynamics in a
river basin. The algorithm was developed in a decision support
system environment in order to enable users to process the data. The
decision support system is found to be useful due to its interactive
nature, flexibility in approach and evolving graphical feature and can
be adopted for any similar situation to predict the flood level. The
main data processing includes the gauging station selection, input
generation, lead-time selection/generation, and length of prediction.
This program enables users to process the flood level data, to
train/test the model using various inputs and to visualize results. The
program code consists of a set of files, which can as well be modified
to match other purposes. This program may also serve as a tool for
real-time flood monitoring and process control. The running results
indicate that the decision support system applied to the flood level
seems to have reached encouraging results for the river basin under
examination. The comparison of the model predictions with the
observed data was satisfactory, where the model is able to forecast
the flood level up to 5 hours in advance with reasonable prediction
accuracy. Finally, this program may also serve as a tool for real-time
flood monitoring and process control.
Abstract: Cow milk, is a product of the mammary gland and
soymilk is a beverage made from soybeans; it is the liquid that
remains after soybeans are soaked. In this research effort, we
compared nutritional parameters of this two kind milk such as total
fat, fiber, protein, minerals (Ca, Fe and P), fatty acids, carbohydrate,
lactose, water, total solids, ash, pH, acidity and calories content in
one cup (245 g). Results showed soymilk contains 4.67 grams of fat,
0.52 of fatty acids, 3.18 of fiber, 6.73 of protein, 4.43 of
carbohydrate, 0.00 of lactose, 228.51 of water, 10.40 of total solids
and 0.66 of ash, also 9.80 milligrams of Ca, 1.42 of Fe, and 120.05 of
P, 79 Kcal of calories, pH=6.74 and acidity was 0.24%. Cow milk
contains 8.15 grams of fat, 5.07 of fatty acids, 0.00 of fiber, 8.02 of
protein, 11.37 of carbohydrate, ´Çá4.27 of lactose, 214.69 of water,
12.90 of total solids, 1.75 of ash, 290.36 milligrams of Ca, 0.12 of
Fe, and 226.92 of P, 150 Kcal of calories, pH=6.90 and acidity was
0.21% . Soy milk is one of plant-based complete proteins and cow
milk is a rich source of nutrients as well. Cow milk is containing near
twice as much fat as and ten times more fatty acids do soymilk. Cow
milk contains greater amounts of mineral (except Fe) it contain more
than three hundred times the amount of Ca and nearly twice the
amount of P as does soymilk but soymilk contains more Fe (ten time
more) than does cow milk. Cow milk and soy milk contain nearly
identical amounts of protein and water and fiber is a big plus, dairy
has none. Although what we choose to drink is really a mater of
personal preference and our health objectives but looking at the
comparison, soy looks like healthier choices.
Abstract: The disaster from functional gastrointestinal disorders has detrimental impact on the quality of life of the effected population and imposes a tremendous social and economic burden. There are, however, rare diagnostic methods for the functional gastrointestinal disorders. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Objective of current study is, therefore, identify feasibility of a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristics above. Two-dimensional finite difference (FD) models (one normal and two rigid model) were developed to analyze the reflective characteristic (displacement) on each soft-tissue layer responded after application of ultrasound signals. The FD analysis was then based on elastic ultrasound theory. Validation of the model was performed via comparison of the characteristic of the ultrasonic responses predicted by FD analysis with that determined from the actual specimens for the normal and rigid conditions. Based on the results from FD analysis, ultrasound system for diagnosis of the functional gastrointestinal disorders was developed and clinically tested via application of it to 40 human subjects with/without functional gastrointestinal disorders who were assigned to Normal and Patient Groups. The FD models were favorably validated. The results from FD analysis showed that the maximum displacement amplitude in the rigid models (0.12 and 0.16) at the interface between the fat and muscle layers was explicitly less than that in the normal model (0.29). The results from actual specimens showed that the maximum amplitude of the ultrasonic reflective signal in the rigid models (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal model (0.1±0.2 Vp-p). Clinical tests using our customized ultrasound system showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3 Vp-p) were generally higher than those in normal group (0.1±0.2 Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These findings suggest that our customized ultrasound system using the ultrasonic reflective signal may be helpful to the diagnosis of the functional gastrointestinal disorders.