Abstract: The aim of this study is to investigate formability of
Al based closed cell metallic foams at high temperature. The foam
specimens with rectangular section were produced from
AlMg1Si0.6TiH20.8 alloy preform material. Bending and free
bending tests based on gravity effect were applied to foam specimens
at high temperatures. During the tests, the time-angular deformation
relationships with various temperatures were determined.
Deformation types formed in cell walls were investigated by means
of Scanning Electron Microscopy (SEM) and optical microscopy.
Bending deformation about 90° was achieved without any defect at
high temperatures. The importance of a critical temperature and
deformation rate was emphasized in maintaining the deformation.
Significant slip lines on surface of cell walls at tensile zones of
bending specimen were observed. At high strain rates, the microcrack
formation in boundaries of elongated grains was determined.
Abstract: This paper investigates simple implicit force control
algorithms realizable with industrial robots. A lot of approaches
already published are difficult to implement in commercial robot
controllers, because the access to the robot joint torques is necessary
or the complete dynamic model of the manipulator is used. In
the past we already deal with explicit force control of a position
controlled robot. Well known schemes of implicit force control are
stiffness control, damping control and impedance control. Using such
algorithms the contact force cannot be set directly. It is further
the result of controller impedance, environment impedance and
the commanded robot motion/position. The relationships of these
properties are worked out in this paper in detail for the chosen
implicit approaches. They have been adapted to be implementable
on a position controlled robot. The behaviors of stiffness control
and damping control are verified by practical experiments. For this
purpose a suitable test bed was configured. Using the full mechanical
impedance within the controller structure will not be practical in the
case when the robot is in physical contact with the environment. This
fact will be verified by simulation.
Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: In this study, firstly democratic thoughts which
directly or indirectly affect economic development and/or the
interaction between authoritarian regimes and the economic
development and the direction and channels of this interaction were
studied and then the study tried to determine how democracy affects
economic development. It was concluded that the positive
contributions of democracy to economic development were more
determinant than the effects that were either negative or restrictive in
terms of development. When compared to autocracy, since
democracy is more successful in managing social conflicts, ensuring
political stability and preventing social disasters such as famine, it
contributes more to economic development. Democracy also
facilitates delegation of authority, provides a stable investment
environment and accelerates mobilization of resources in accordance
with economic growth/development. Democracy leads to an increase
in human capital accumulation and increases the growth rate through
reducing income inequality. It can be said that democratic regimes
are the most appropriate ones in terms of increasing economic
performance and supporting economic development through their
strong institutional structures and the assurance they will ensure in
property rights.
Abstract: Background: Worldwide, at least 2.8 million people
die each year as a result of being overweight or obese, and 35.8
million (2.3%) of global DALYs are caused by overweight or
obesity. Obesity is acknowledged as one of the burning public
health problems reducing life expectancy and quality of life. The
body composition analysis of the university population is essential
in assessing the nutritional status, as well as the risk of developing
diseases associated with abnormal body fat content so as to make
nutritional recommendations. Objectives: The main aim was to
determine the prevalence of obesity and overweight in University
students using Anthropometric analysis and BIA methods. Material
and Methods: In this cross-sectional study, 283 university students
participated. The body composition analysis was undertaken by
using mainly: i) Anthropometric Measurement: Height, Weight,
BMI, waist circumference, hip circumference and skin fold
thickness, ii) Bio-electrical impedance was used for analysis of
body fat mass, fat percent and visceral fat which was measured by
Tanita SC-330P Professional Body Composition Analyzer. The
data so collected were compiled in MS Excel and analyzed for
males and females using SPSS 16. Results and Discussion: The
mean age of the male (n= 153) studied subjects was 25.37 ±2.39
years and females (n=130) was 22.53 ±2.31. The data of BIA
revealed very high mean fat per cent of the female subjects i.e.
30.3±6.5 per cent whereas mean fat per cent of the male subjects
was 15.60±6.02 per cent indicating a normal body fat range. The
findings showed high visceral fat of both males (12.92±3.02) and
females (16.86±4.98). BMI, BF% and WHR were higher among
females, and BMI was higher among males. The most evident
correlation was verified between BF% and WHR for female
students (r=0.902; p
Abstract: Family is a basic unit of the society and the main
source of human development. The initial aim of the family is
psychological and social support of its members and has special
developmental stages. Researches show the families who have less
cohesion, have more conflicts and maladjustments and the members
of such families are not able to communicate effectively. Family is a
system in which any inter communication is related to child rearing
patterns and can affect it. Even the child rearing styles in childhood
can determine the family communications in adulthood. Therefore,
the aim of the present research was to examine the relationship
between child-rearing styles including authoritative, authoritarian and
permissive with dimensions of family communication patterns
including the conversation and conformity. The research design was a
correlational and the population consisted of the psychology students
of Roudehen Islamic Azad University who were studying in
academic year 2013-2014. A sample of 324 students was selected
randomly from the population. The research tools were the Baumrind
Child-rearing Questionnaires and Family Communication
Patterns Inventory, The Revised Scale of Koerner and Fitzpatrick.
The result was as below: (a) there was a positive and significant
relationship between conversation orientation and authoritative style.
(b) There was no significant relationship between conversation
orientation and other child-rearing styles. (c) There was a negative
significant relationship between conformity orientation and
authoritative style. (d) There was a positive significant relationship
between conformity orientation with authoritarian and permissive
styles. (e) There was a significant relationship between 3 dimensions
of child-rearing and communication patterns.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: Dielectric ceramic samples in the BaO-Re2O3-TiO2
ternary system were synthesized with structural formula Ba2-
xRe4+2x/3Ti8O24 where Re= rare earth metal and Re= Sm and La where
x varies from 0.0 to 0.6 with step size 0.1. Polycrystalline samples
were prepared by the conventional solid state reaction technique. The
dielectric, electrical and impedance analysis of all the samples in the
frequency range 1KHz- 1MHz at room temperature (25°C) have been
done to get the understanding of electrical conduction and dielectric
relaxation and their correlation. Dielectric response of the samples at
lower frequencies shows dielectric dispersion while at higher
frequencies it shows dielectric relaxation. The ac conductivity is well
fitted by the Jonscher law. The spectroscopic data in the impedance
plane confirms the existence of grain contribution to the relaxation.
All the properties are found out to be function of frequency as well as
the amount of substitution.
Abstract: This paper presents a rank correlation curve. The
traditional correlation coefficient is valid for both continuous
variables and for integer variables using rank statistics. Since
the correlation coefficient has already been established in rank
statistics by Spearman, such a calculation can be extended to
the correlation curve.
This paper presents two survey questions. The survey
collected non-continuous variables. We will show weak to
moderate correlation. Obviously, one question has a negative
effect on the other. A review of the qualitative literature
can answer which question and why. The rank correlation
curve shows which collection of responses has a positive
slope and which collection of responses has a negative slope.
Such information is unavailable from the flat, ”first-glance”
correlation statistics.
Abstract: The article represents the results of isolation and
component chromatographic analysis of essential oils of Polygonym
L. plants growing in Kazakhstan in commercial reserves at the
territory of Kazakhstan. The results of research of antiviral activity of
isolated substances to flu virus have been represented in this article.
The main pharmacophore groups in the structure of alkaloids have
been identified.
Abstract: The posterior reference for the ala tragal line is a
cause of confusion, with different authors suggesting different
locations as to the superior, middle or inferior part of the tragus. This
study was conducted on 200 subjects to evaluate if any correlation
exists between the variation of angulation of palatal throat form and
the relative parallelism of occlusal plane to ala-tragal line at different
tragal levels. A custom made Occlusal Plane Analyzer was used to
check the parallelism between the ala-tragal line and occlusal plane.
A lateral cephalogram was shot for each subject to measure the
angulation of the palatal throat form. Fisher’s exact test was used to
evaluate the correlation between the angulation of the palatal throat
form and the relative parallelism of occlusal plane to the ala tragal
line. Also, a classification was formulated for the palatal throat form,
based on confidence interval. From the results of the study, the
inferior part, middle part and superior part of the tragus were seen as
the reference points in 49.5%, 32% and 18.5% of the subjects
respectively. Class I palatal throat form (41degree-50 degree), Class
II palatal throat form (below 41 degree) and Class III palatal throat
form (above 50 degree) were seen in 42%, 43% and 15% of the
subjects respectively. It was also concluded that there is no
significant correlation between the variation in the angulations of the
palatal throat form and the relative parallelism of occlusal plane to
the ala-tragal line.
Abstract: Many factors influence the educational outcome of
students. Some of these have been studied by researchers with many
emphasizing the role of students, schools, governments, peer groups
and so on. More often than not, some of these factors influencing the
academic achievement of the students have been traced back to
parents and family; being the primary platform on which learning not
only begins but is nurtured, encouraged and developed which later
transforms to the performance of the students. This study not only
explores parental and related factors that predict academic
achievement through the review of relevant literatures but also,
investigates the influence of parental background on the academic
achievement of senior secondary school students in Ibadan North
Local Government Area of Oyo State, Nigeria. As one of the criteria
of the quality of education, students’ academic achievement was
investigated because it is most often cited as an indicator of school
effectiveness by school authorities and educationists. The data
collection was done through interviews and use of well-structured
questionnaires administered to one hundred students (100) within the
target local government. This was statistically analysed and the result
showed that parents’ attitudes towards their children’s education had
significant effect(s) on students’ self-reporting of academic
achievement. However, such factors as parental education and socioeconomic
background had no significant relationship with the
students’ self-reporting of academic achievement.
Abstract: All current experimental methods for determination of
stress intensity factors are based on the assumption that the state of
stress near the crack tip is plane stress. Therefore, these methods rely
on strain and displacement measurements made outside the near
crack tip region affected by the three-dimensional effects or by
process zone. In this paper, we develop and validate an experimental
procedure for the evaluation of stress intensity factors from the
measurements of the out-of-plane displacements in the surface area
controlled by 3D effects. The evaluation of stress intensity factors is
possible when the process zone is sufficiently small, and the
displacement field generated by the 3D effects is fully encapsulated
by K-dominance region.
Abstract: The grain quality of chickpea in Iran is low and
instable, which may be attributed to the evolution of cultivars with a
narrow genetic base making them vulnerable to biotic stresses. Four
chickpea varieties from diverse geographic origins were chosen and
arranged in a randomized complete block design. Mesorhizobium sp.
cicer strain SW7 was added to all the chickpea seeds. Chickpea seeds
were planted on October 9, 2013. Each genotype was sown 5 m in
length, with 35 cm inter-row spacing, in 3 rows. Weeds were
removed manually in all plots. Results showed that Analysis of
variance on the studied traits showed significant differences among
genotypes for N, P, K and Fe contents of chickpea, but there is not a
significant difference among Ca, Zn and Mg continents of chickpea.
The experimental coefficient of variation (CV) varied from 7.3 to
15.8. In general, the CV value lower than 20% is considered to be
good, indicating the accuracy of conducted experiments. The highest
grain N was observed in Hashem and Jam cultivars. The highest grain
P was observed in Jam cultivar. Phosphorus content (mg/100g)
ranged from 142.3 to 302.3 with a mean value of 221.3. The negative
correlation (-0.126) was observed between the N and P of chickpea
cultivars. The highest K and Fe contents were observed in Jam
cultivar.
Abstract: In Hungary, the society has changed a lot for the past
25 years, and these changes could be detected in educational
situations as well. The number and the intensity of conflicts have
been increased in most fields of life, as well as at schools. Teachers
have difficulties to be able to handle school conflicts. What is more,
the new net generation, generation Z has values and behavioural
patterns different from those of the previous one, which might
generate more serious conflicts at school, especially with teachers
who were mainly socialising in a traditional teacher – student
relationship.
In Hungary, the bill CCIV of 2011 declared the foundation of
Institutes of Teacher Training in higher education institutes. One of
the tasks of the Institutes is to survey the competences and needs of
teachers working in public education and to provide further trainings
and services for them according to their needs and requirements. This
job is supported by the Social Renewal Operative Programs 4.1.2.B.
The professors of a college carried out a questionnaire and surveyed
the needs and the requirements of teachers working in the region.
Based on the results, the professors of the Institute of Teacher
Training decided to meet the requirements of teachers and to launch
short teacher further training courses in spring 2015. One of the
courses is going to focus on school conflict management through
mediation.
The aim of the pilot course is to provide conflict management
techniques for teachers and to present different mediation techniques
to them. The theoretical part of the course (5 hours) will enable
participants to understand the main points and the advantages of
mediation, while the practical part (10 hours) will involve teachers in
role plays to learn how to cope with conflict situations applying
mediation. We hope if conflicts could be reduced, it would influence
school atmosphere in a positive way and the teaching – learning
process could be more successful and effective.
Abstract: Prosperity of electronic equipment in photocopying
environment not only has improved work efficiency, but also has
changed indoor air quality. Considering the number of photocopying
employed, indoor air quality might be worse than in general office
environments. Determining the contribution from any type of
equipment to indoor air pollution is a complex matter. Non-methane
hydrocarbons are known to have an important role on air quality due
to their high reactivity. The presence of hazardous pollutants in
indoor air has been detected in one photocopying shop in Novi Sad,
Serbia. Air samples were collected and analyzed for five days, during
8-hr working time in three time intervals, whereas three different
sampling points were determined. Using multiple linear regression
model and software package STATISTICA 10 the concentrations of
occupational hazards and microclimates parameters were mutually
correlated. Based on the obtained multiple coefficients of
determination (0.3751, 0.2389 and 0.1975), a weak positive
correlation between the observed variables was determined. Small
values of parameter F indicated that there was no statistically
significant difference between the concentration levels of nonmethane
hydrocarbons and microclimates parameters. The results
showed that variable could be presented by the general regression
model: y = b0 + b1xi1+ b2xi2. Obtained regression equations allow to
measure the quantitative agreement between the variables and thus
obtain more accurate knowledge of their mutual relations.
Abstract: The growth in the volume of text data such as books
and articles in libraries for centuries has imposed to establish
effective mechanisms to locate them. Early techniques such as
abstraction, indexing and the use of classification categories have
marked the birth of a new field of research called "Information
Retrieval". Information Retrieval (IR) can be defined as the task of
defining models and systems whose purpose is to facilitate access to
a set of documents in electronic form (corpus) to allow a user to find
the relevant ones for him, that is to say, the contents which matches
with the information needs of the user. This paper presents a new
semantic indexing approach of a documentary corpus. The indexing
process starts first by a term weighting phase to determine the
importance of these terms in the documents. Then the use of a
thesaurus like Wordnet allows moving to the conceptual level.
Each candidate concept is evaluated by determining its level of
representation of the document, that is to say, the importance of the
concept in relation to other concepts of the document. Finally, the
semantic index is constructed by attaching to each concept of the
ontology, the documents of the corpus in which these concepts are
found.
Abstract: The relationship between the state and the religion is
different based on the fact that how powerful is the religion faith in a
state and of the influences that affected the views of the constitution
drafters according to the constitutional system they were based to
draft their constitution. This paper aims at providing, through a
comparative methodology, how it is regulated by the constitution the
relationship between the state and the religion. The object of this
study are the constitutions of Italy as a nation with catholic religious
tradition, Greece as a nation with orthodox religion tradition, and
Turkey as a nation which represents Muslim religion, while Albania
as a nation known for its religious plurality. In particular, the analysis
will be focused on the secular or religious principle provided in the
constitution of each respective state. This comparative overview
intends to discern which of the states analyzed is more tolerant and
fully respects the freedom of religion. It results that most of the states
subject of this study, despite their religious tradition have chosen the
secular principle in their constitutions, but the religious freedom is
differently guaranteed.
Abstract: Quick adoption of e-business and emerging influence
of “Electronic Word of Mouth e-WOM” communication on guests
made leading hotel brands successful examples of electronic guest
relationship management. Main reasons behind such success are well
established procedures in collection, analysis and usage of highly
valuable data available on the Internet, generated through some form
of e-GRM programme. E-GRM is more than just a technology
solution. It’s a system which balance respective guest demands, hotel
technological capabilities and organizational culture of employees,
discharging the universal approach in guest relations “same for all”.
The purpose of this research derives from the necessity of
determining the importance of monitoring and applying e-WOM
communication as one of the methods used in managing guest
relations. This paper analyses and compares different hotelier’s
opinions on e-WOM communication.
Abstract: In this paper we propose a novel methodology for
extracting a road network and its nodes from satellite images of
Algeria country.
This developed technique is a progress of our previous research
works. It is founded on the information theory and the mathematical
morphology; the information theory and the mathematical
morphology are combined together to extract and link the road
segments to form a road network and its nodes.
We therefore have to define objects as sets of pixels and to study
the shape of these objects and the relations that exist between them.
In this approach, geometric and radiometric features of roads are
integrated by a cost function and a set of selected points of a crossing
road. Its performances were tested on satellite images of Algeria
country.