Abstract: The human knee joint has a three dimensional
geometry with multiple body articulations that produce complex
mechanical responses under loads that occur in everyday life and
sports activities. To produce the necessary joint compliance and
stability for optimal daily function various menisci and ligaments are
present while muscle forces are used to this effect. Therefore,
knowledge of the complex mechanical interactions of these load
bearing structures is necessary when treatment of relevant diseases is
evaluated and assisting devices are designed.
Numerical tools such as finite element analysis are suitable for
modeling such joints in order to understand their physics. They have
been used in the current study to develop an accurate human knee
joint and model its mechanical behavior. To evaluate the efficacy of
this articulated model, static load cases were used for comparison
purposes with previous experimentally verified modeling works
drawn from literature.
Abstract: This paper systematically investigates the timedependent
health outcomes for office staff during computer work
using the developed mathematical model. The model describes timedependent
health outcomes in multiple body regions associated with
computer usage. The association is explicitly presented with a doseresponse
relationship which is parametrized by body region
parameters. Using the developed model we perform extensive
investigations of the health outcomes statically and dynamically. We
compare the risk body regions and provide various severity rankings
of the discomfort rate changes with respect to computer-related
workload dynamically for the study population. Application of the
developed model reveals a wide range of findings. Such broad
spectrum of investigations in a single report literature is lacking.
Based upon the model analysis, it is discovered that the highest
average severity level of the discomfort exists in neck, shoulder, eyes,
shoulder joint/upper arm, upper back, low back and head etc. The
biggest weekly changes of discomfort rates are in eyes, neck, head,
shoulder, shoulder joint/upper arm and upper back etc. The fastest
discomfort rate is found in neck, followed by shoulder, eyes, head,
shoulder joint/upper arm and upper back etc. Most of our findings are
consistent with the literature, which demonstrates that the developed
model and results are applicable and valuable and can be utilized to
assess correlation between the amount of computer-related workload
and health risk.
Abstract: Prediction of highly non linear behavior of suspended
sediment flow in rivers has prime importance in the field of water
resources engineering. In this study the predictive performance of
two Artificial Neural Networks (ANNs) namely, the Radial Basis
Function (RBF) Network and the Multi Layer Feed Forward (MLFF)
Network have been compared. Time series data of daily suspended
sediment discharge and water discharge at Pari River was used for
training and testing the networks. A number of statistical parameters
i.e. root mean square error (RMSE), mean absolute error (MAE),
coefficient of efficiency (CE) and coefficient of determination (R2)
were used for performance evaluation of the models. Both the models
produced satisfactory results and showed a good agreement between
the predicted and observed data. The RBF network model provided
slightly better results than the MLFF network model in predicting
suspended sediment discharge.
Abstract: Nowadays increasingly the population makes use of
Information Technology (IT). As such, in recent year the Portuguese
government increased its focus on using the IT for improving
people-s life and began to develop a set of measures to enable the
modernization of the Public Administration, and so reducing the gap
between Public Administration and citizens.Thus the Portuguese
Government launched the Simplex Program. However these
SIMPLEX eGov measures, which have been implemented over the
years, present a serious challenge: how to forecast its impact on
existing Information Systems Architecture (ISA). Thus, this research
is focus in addressing the problem of automating the evaluation of the
actual impact of implementation an eGovSimplification and
Modernization measures in the Information Systems Architecture. To
realize the evaluation we proposes a Framework, which is supported
by some key concepts as: Quality Factors, ISA modeling,
Multicriteria Approach, Polarity Profile and Quality Metrics
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Abstract: Software security testing is an important means to ensure software security and trustiness. This paper first mainly discusses the definition and classification of software security testing, and investigates methods and tools of software security testing widely. Then it analyzes and concludes the advantages and disadvantages of various methods and the scope of application, presents a taxonomy of security testing tools. Finally, the paper points out future focus and development directions of software security testing technology.
Abstract: An on-demand routing protocol for wireless ad hoc
networks is one that searches for and attempts to discover a route to
some destination node only when a sending node originates a data
packet addressed to that node. In order to avoid the need for such a
route discovery to be performed before each data packet is sent, such
routing protocols must cache routes previously discovered. This
paper presents an analysis of the effect of intelligent caching in a non
clustered network, using on-demand routing protocols in wireless ad
hoc networks. The analysis carried out is based on the Dynamic
Source Routing protocol (DSR), which operates entirely on-demand.
DSR uses the cache in every node to save the paths that are learnt
during route discovery procedure. In this implementation, caching
these paths only at intermediate nodes and using the paths from these
caches when required is tried. This technique helps in storing more
number of routes that are learnt without erasing the entries in the
cache, to store a new route that is learnt.
The simulation results on DSR have shown that this technique
drastically increases the available memory for caching the routes
discovered without affecting the performance of the DSR routing
protocol in any way, except for a small increase in end to end delay.
Abstract: Medical image registration is the key technology in image guided radiation therapy (IGRT) systems. On the basis of the previous work on our IGRT prototype with a biorthogonal x-ray imaging system, we described a method focused on the 2D/2D rigid-body registration using multiresolution pyramid based mutual information in this paper. Three key steps were involved in the method ： firstly, four 2D images were obtained including two x-ray projection images and two digital reconstructed radiographies（DRRs ） as the input for the registration ； Secondly, each pair of the corresponding x-ray image and DRR image were matched using multiresolution pyramid based mutual information under the ITK registration framework ； Thirdly, we got the final couch offset through a coordinate transformation by calculating the translations acquired from the two pairs of the images. A simulation example of a parotid gland tumor case and a clinical example of an anthropomorphic head phantom were employed in the verification tests. In addition, the influence of different CT slice thickness were tested. The simulation results showed that the positioning errors were 0.068±0.070, 0.072±0.098, 0.154±0.176mm along three axes which were lateral, longitudinal and vertical. The clinical test indicated that the positioning errors of the planned isocenter were 0.066, 0.07, 2.06mm on average with a CT slice thickness of 2.5mm. It can be concluded that our method with its verified accuracy and robustness can be effectively used in IGRT systems for patient setup.
Abstract: The development of information and communication
technology, the increased use of the internet, as well as the effects of
the recession within the last years, have lead to the increased use of
cloud computing based solutions, also called on-demand solutions.
These solutions offer a large number of benefits to organizations as
well as challenges and risks, mainly determined by data visualization
in different geographic locations on the internet. As far as the specific
risks of cloud environment are concerned, data security is still
considered a peak barrier in adopting cloud computing. The present
study offers an approach upon ensuring the security of cloud data,
oriented towards the whole data life cycle. The final part of the study
focuses on the assessment of data security in the cloud, this
representing the bases in determining the potential losses and the
premise for subsequent improvements and continuous learning.
Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: Insulation used in transformer is mostly oil pressboard insulation. Insulation failure is one of the major causes of catastrophic failure of transformers. It is established that partial discharges (PD) cause insulation degradation and premature failure of insulation. Online monitoring of PDs can reduce the risk of catastrophic failure of transformers. There are different techniques of partial discharge measurement like, electrical, optical, acoustic, opto-acoustic and ultra high frequency (UHF). Being non invasive and non interference prone, acoustic emission technique is advantageous for online PD measurement. Acoustic detection of p.d. is based on the retrieval and analysis of mechanical or pressure signals produced by partial discharges. Partial discharges are classified according to the origin of discharges. Their effects on insulation deterioration are different for different types. This paper reports experimental results and analysis for classification of partial discharges using acoustic emission signal of laboratory simulated partial discharges in oil pressboard insulation system using three different electrode systems. Acoustic emission signal produced by PD are detected by sensors mounted on the experimental tank surface, stored on an oscilloscope and fed to computer for further analysis. The measured AE signals are analyzed using discrete wavelet transform analysis and wavelet packet analysis. Energy distribution in different frequency bands of discrete wavelet decomposed signal and wavelet packet decomposed signal is calculated. These analyses show a distinct feature useful for PD classification. Wavelet packet analysis can sort out any misclassification arising out of DWT in most cases.
Abstract: A comparative study on the feasibility of producing instant high fibre plantain flour for diabetic fufu by blending soy residence with different plantain (Musa spp) varieties (Horn, false Horn and French), all sieved at 60 mesh, mixed in ratio of 60:40 was analyzed for their passing properties using standard analytical method. Results show that VIIIS60 had the highest peak viscosity (303.75 RVU), Trough value (182.08 RVU), final viscosity (284.50 RVU), and lowest in breakdown viscosity (79.58 RVU), set back value (88.17 RVU), peak time (4.36min), pasting temperature (81.18°C) and differed significantly (p
Abstract: The current research paper is an implementation of
Eigen Faces and Karhunen-Loeve Algorithm for face recognition.
The designed program works in a manner where a unique
identification number is given to each face under trial. These faces
are kept in a database from where any particular face can be matched
and found out of the available test faces. The Karhunen –Loeve
Algorithm has been implemented to find out the appropriate right
face (with same features) with respect to given input image as test
data image having unique identification number. The procedure
involves usage of Eigen faces for the recognition of faces.
Abstract: Cardiac pulse-related artifacts in the EEG recorded
simultaneously with fMRI are complex and highly variable. Their
effective removal is an unsolved problem. Our aim is to develop an
adaptive removal algorithm based on the matching pursuit (MP)
technique and to compare it to established methods using a visual
evoked potential (VEP). We recorded the VEP inside the static
magnetic field of an MR scanner (with artifacts) as well as in an
electrically shielded room (artifact free). The MP-based artifact
removal outperformed average artifact subtraction (AAS) and
optimal basis set removal (OBS) in terms of restoring the EEG field
map topography of the VEP. Subsequently, a dipole model was fitted
to the VEP under each condition using a realistic boundary element
head model. The source location of the VEP recorded inside the MR
scanner was closest to that of the artifact free VEP after cleaning
with the MP-based algorithm as well as with AAS. While none of the
tested algorithms offered complete removal, MP showed promising
results due to its ability to adapt to variations of latency, frequency
and amplitude of individual artifact occurrences while still utilizing a
common template.
Abstract: In this paper, an ultrasonic technique is proposed to
predict oil content in a fresh palm fruit. This is accomplished by
measuring the attenuation based on ultrasonic transmission mode.
Several palm fruit samples with known oil content by Soxhlet
extraction (ISO9001:2008) were tested with our ultrasonic
measurement. Amplitude attenuation data results for all palm samples
were collected. The Feedforward Neural Networks (FNNs) are
applied to predict the oil content for the samples. The Root Mean
Square Error (RMSE) and Mean Absolute Error (MAE) of the FNN
model for predicting oil content percentage are 7.6186 and 5.2287
with the correlation coefficient (R) of 0.9193.
Abstract: Noise causes significant sensibility changes on a human. This study investigated the effect of five different noises on electroencephalogram (EEG) and subjective evaluation. Six human subjects were exposed to classic piano, ocean wave, alarm in army, ambulance, mosquito noise and EEG data were collected during the experimental session. Alpha band activity in the mosquito noise was smaller than that in the classic piano. Alpha band activity decreased 43.4 ± 8.2 % in the mosquito noise. On the other hand, Beta band activity in the mosquito noise was greater than that in the classic piano. Beta band activity increased 60.1 ± 10.7 % in the mosquito noise. The advances from this study may aid the product design process with human sensibility engineering. This result may provide useful information in designing a human-oriented product to avoid the stress.
Abstract: Thermodynamics characterization Sesame oil
extraction by Acetone, Hexane and Benzene has been evaluated. The
120 hours experimental Data were described by a simple
mathematical model. According to the simulation results and the
essential criteria, Acetone is superior to other solvents but under
certain conditions where oil extraction takes place Hexane is superior
catalyst.
Abstract: In Thailand, both the 1997 and the current 2007 Thai Constitutions have mentioned the establishment of independent organizations as a new mechanism to play a key role in proposing policy recommendations to national decision-makers in the interest of collective consumers. Over the last ten years, no independent organizations have yet been set up. Evidently, nobody could point out who should be key players in establishing provincial independent consumer bodies. The purpose of this study was to find definitive stakeholders in establishing and developing independent consumer bodies in a Thai context. This was a cross-sectional study between August and September 2007, using a postal questionnaire with telephone follow-up. The questionnaire was designed and used to obtain multiple stakeholder assessment of three key attributes (power, interest and influence). Study population was 153 stakeholders associated with policy decision-making, formulation and implementation processes of civil-based consumer protection in pilot provinces. The population covered key representatives from five sectors (academics, government officers, business traders, mass media and consumer networks) who participated in the deliberative forums at 10 provinces. A 49.7% response rate was achieved. Data were analyzed, comparing means of three stakeholder attributes and classification of stakeholder typology. The results showed that the provincial health officers were the definitive stakeholders as they had legal power, influence and interest in establishing and sustaining the independent consumer bodies. However, only a few key representatives of the provincial health officers expressed their own paradigm on the civil-based consumer protection. Most provincial health officers put their own standpoint of building civic participation at only a plan-implementation level. For effective policy implementation by the independent consumer bodies, the Thai government should provide budgetary support for the operation of the provincial health officers with their paradigm shift as well as their own clarified standpoint on corporate governance.
Abstract: The textile industry produces highly coloured
effluents containing polar and non-polar compounds. The textile mill
run by the Assam Polyester Co-operative Society Limited (APOL) is
situated at Rangia, about 55 km from Guwahati (26011' N, 91047' E)
in the northern bank of the river Brahmaputra, Assam (India). This
unit was commissioned in June 1988 and started commercial
production in November 1988. The installed capacity of the weaving
unit was 8000 m/day and that of the processing unit was 20,000
m/day. The mill has its own dyeing unit with a capacity of 1500-2000
kg/day. The western side of the mill consists of vast agricultural land
and the far northern and southern side of the mill has scattered human
population. The eastern side of the mill has a major road for
thoroughfare. The mill releases its effluents into the agricultural land
in the western side of the mill. The present study was undertaken to
assess the impact of the textile mill on surface soil quality in and
around the mill with particular reference to Cr, Mn, Ni and Zn.
Surface soil samples, collected along different directions at 200, 500
and 1000 m were digested and the metals were estimated with
Atomic Absorption Spectrophotometer. The metals were found in the
range of: Cr 50.9 – 105.0 mg kg-1, Mn 19.2- 78.6 mg kg-1, Ni 41.9 –
50.6 mg kg-1 and Zn 187.8 – 1095.8 mg kg-1. The study reveals
enrichment of Cr, Mn, Ni and Zn in the soil near the textile mill.
Abstract: Security risk models have been successful in estimating the likelihood of attack for simple security threats. However, modeling complex system and their security risk is even a challenge. Many methods have been proposed to face this problem. Often difficult to manipulate, and not enough all-embracing they are not as famous as they should with administrators and deciders. We propose in this paper a new tool to model big systems on purpose. The software, takes into account attack threats and security strength.