Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: The present study was carried out to evaluate the
effect of different levels of dietary seed and extract of Harmal
(Peganum harmala L.) on immunity of broiler chicks. A total of 350
one-day old broiler chicks (Ross 308) were randomly allocated to
five dietary treatments with four replicates pen of 14 birds each.
Dietary treatments consisted of control, 1 and 2 g/kg Harmal seed in
diet, 100 and 200 mg/L Harmal seed extract in water. Broilers
received dietary treatments from 1 to 42 d. Two birds from each pen
were randomly weighed and sacrificed at 42 d of age, the relative
weight of lymphoid organs (bursa of Fabercius and spleen) to live
weight were calculated. Antibody titers against Newcastle and
influenza viruses and sheep red blood cell were measured at 30 d of
age. Results showed that the relative weights of lymphoid organs
were not affected by dietary treatments. Furthermore, antibody titer
against Newcastle and influenza viruses as well as sheep red blood
cell antigen were significantly (P
Abstract: In this study a ternary system containing sodium
chloride as solute, water as primary solvent and ethanol as the
antisolvent was considered to investigate the application of artificial
neural network (ANN) in prediction of sodium solubility in the
mixture of water as the solvent and ethanol as the antisolvent. The
system was previously studied using by Extended UNIQUAC model
by the authors of this study. The comparison between the results of
the two models shows an excellent agreement between them
(R2=0.99), and also approves the capability of ANN to predict the
thermodynamic behavior of ternary electrolyte systems which are
difficult to model.
Abstract: A thermosyphon system is a heat transfer loop which
operates on the basis of gravity and buoyancy forces. It guarantees a
good reliability and low maintenance cost as it does not involve any
mechanical pump. Therefore, it can be used in many industrial
applications such as refrigeration and air conditioning, electronic
cooling, nuclear reactors, geothermal heat extraction, etc. But flow
instabilities and loop configuration are the major problems in this
system. Several previous researchers studied that stabilities can be
suppressed by using nanofluids as loop fluid. In the present study a
rectangular thermosyphon loop with end heat exchangers are
considered for the study. This configuration is more appropriate for
many practical applications such as solar water heater, geothermal
heat extraction, etc. In the present work, steady-state analysis is
carried out on thermosyphon loop with parallel flow coaxial heat
exchangers at heat source and heat sink. In this loop nanofluid is
considered as the loop fluid and water is considered as the external
fluid in both hot and cold heat exchangers. For this analysis onedimensional
homogeneous model is developed. In this model,
conservation equations like conservation of mass, momentum, energy
are discretized using finite difference method. A computer code is
written in MATLAB to simulate the flow in thermosyphon loop. A
comparison in terms of heat transfer is made between water and
nanofluid as working fluids in the loop.
Abstract: The objective of this research is to design and
construct the PV-Wind hybrid autonomous system for the greenhouse
plantation, and analyze the technical performance of the PV-Wind
energy system. This design depends on the water consumption in the
greenhouse by using 24 of the fogging mist each with the capability
of 24 liter/min. The operating time is 4 times per day, each round for
15 min. The fogging system is being driven by water pump with AC
motor rating 0.5 hp. The load energy consumed is around 1.125
kWh/d. The designing results of the PV-Wind hybrid energy system
is that sufficient energy could be generated by this system. The
results of this study can be applied as a technical data reference for
other areas in the central part of Thailand.
Abstract: Karst term is the determiner of a variety of areas or
landforms and unique perspectives that have been formed in result of
the of the ingredients dissolution of rocks constituter by natural
waters. Shiraz area with an area of 5322km2 is located in the simple
folded belt in the southern part of Zagros Mountain of Fars, and is
surrounded with Limestone Mountains (Asmari formation). Shiraz
area is located in Calcareous areas. The infrastructure of this city is
lime and absorbing wells that the city can influence the Limestone
dissolution and those accelerate its rate and increase the cavitation
below the surface. Dasht-e Arjan is a graben, which has been created
as the result of activity of two normal faults in its east and west sides.
It is a complete sample of Karst plains (Polje) which has been created
with the help of tectonic forces (fault) and dissolution process of
water in Asmari limestone formation. It is located 60km. off south
west of Shiraz (on Kazeroon-Shiraz road). In 1971, UNESCO has
recognized this plain as a reserve of biosphere. It is considered as one
of the world’s most beautiful geological phenomena, so that most of
the world’s geologists are interested in visiting this place. The
purpose of this paper is to identify and introduce landscapes of Karst
features shiraz city and Dasht-e Arjan including Karst dissolution
features (Lapiez, Karst springs, dolines, caves, underground caves,
ponors, and Karst valleys), anticlines and synclines, and Arjan Lake.
Abstract: Replacement of plastics used in the food industry
seems to be a serious issue to overcome mainly the environmental
problems in recent years. This study investigates the hydrophilicity
and permeability properties of starch biopolymer which ethylene
vinyl alcohol (EVOH) (0-10%) and nanocrystalline cellulose (NCC)
(1-15%) were used to enhance its properties. Starch -EVOH
nanocomposites were prepared by casting method in different
formulations. NCC production by acid hydrolysis was confirmed by
scanning electron microscopy. Solubility, water vapor permeability,
water vapor transmission rate and moisture absorbance were
measured on each of the nanocomposites. The results were analyzed
by SAS software. The lowest moisture absorbance was measured in
pure starch nanocomposite containing 8% NCC. The lowest
permeability to water vapor belongs to starch nanocomposite
containing 8% NCC and the sample containing 7.8% EVOH and 13%
NCC. Also the lowest solubility was observed in the composite
contains the highest amount of EVOH. Applied Process resulted in
production of bio films which have good resistance to water vapor
permeability and solubility in water. The use of NCC and EVOH
leads to reduced moisture absorbance property of the biofilms.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: In the present study, mixed convection in a horizontal
rectangular duct using Al2O3 is numerically investigated. The effects
of different Rayleigh number, Reynolds number and radiation on
flow and heat transfer characteristics are studied in detail. This study
covers Rayleigh number in the range of 2 × 10^6 ≤ Ra ≤ 2 × 10^7 and
Reynolds number in the range of 100 ≤ Re ≤ 1100. Results reveal that
the Nusselt number increases as Reynolds and Rayleigh numbers
increase. It is also found that the dimensionless temperature
distribution increases as Rayleigh number increases.
Abstract: In this paper, extract of papaya leaves are used as a
natural dye and combined by variations of solvent concentration
applied on DSSC (Dye-Sensitized Solar Cell). Indonesian geographic
located on the equator line occasions the magnitude of the potential
to develop organic solar cells made from extracts of chlorophyll as a
substitute for inorganic materials or synthetic dye on DSSC material.
Dye serves as absorbing photons which are then converted into
electrical energy. A conductive coated glass layer called TCO
(Transparent Conductive Oxide) is used as a substrate of electrode.
TiO2 nanoparticles as binding dye molecules, redox couple iodide/
tri-iodide as the electrolyte and carbon as the counter electrode in the
DSSC are used. TiO2 nanoparticles, organic dyes, electrolytes, and
counter electrode are arranged and combined with the layered
structure of the photo-catalyst absorption layer. Dye absorption
measurements using a spectrophotometer at 400-800 nm light
spectrum produces a total amount of chlorophyll 80.076 mg/l. The
test cell at 7 watt LED light with 5000 lux luminescence was
obtained Voc and Isc of 235.5 mV and 14 μA, respectively.
Abstract: Due to water shortage, application of saline water for
irrigation is an urgent in agriculture. In this study the effect of
calcium and potassium application as additive in saline root media for
reduce salinity adverse effects was investigated on tomato growth in
a hydroponic system with unequal distribution of salts in the root
media, which was divided in to two equal parts containing full
Johnson nutrient solution and 40 mMNaCl solution, alone or in
combination with KCl (6 mM), CaCl2 (4 mM), K+Ca (3+2 mM) or
half-strength Johnson nutrient solution. The root splits were
exchanged every 7 days. Results showed that addition of calcium,
calcium-potassium and nutrition elements equivalent to half the
concentration of Johnson formula to the saline-half of culture media
minimized the reduction in plant growth caused by NaCl, although
addition of potassium to culture media wasn’t effective. The greatest
concentration of sodium was observed at the shoot of treatments
which had smallest growth. According to the results of this study, in
case of dynamic and non-uniform distribution of salts in the root
media, by addition of additive to the saline solution, it would be
possible to use of saline water with no significant growth reduction.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: Water spray cooling is a technique typically used in
heat treatment and other metallurgical processes where controlled
temperature regimes are required. Water spray cooling is used in
static (without movement) or dynamic (with movement of the steel
plate) regimes. The static regime is notable for the fixed position of
the hot steel plate and fixed spray nozzle. This regime is typical for
quenching systems focused on heat treatment of the steel plate. The
second application of spray cooling is the dynamic regime. The
dynamic regime is notable for its static section cooling system and
moving steel plate. This regime is used in rolling and finishing mills.
The fixed position of cooling sections with nozzles and the
movement of the steel plate produce nonhomogeneous water
distribution on the steel plate. The length of cooling sections and
placement of water nozzles in combination with the nonhomogeneity
of water distribution lead to discontinued or interrupted cooling
conditions. The impact of static and dynamic regimes on cooling
intensity and the heat transfer coefficient during the cooling process
of steel plates is an important issue.
Heat treatment of steel is accompanied by oxide scale growth. The
oxide scale layers can significantly modify the cooling properties and
intensity during the cooling. The combination of static and dynamic
(section) regimes with the variable thickness of the oxide scale layer
on the steel surface impact the final cooling intensity. The study of
the influence of the oxide scale layers with different cooling regimes
was carried out using experimental measurements and numerical
analysis. The experimental measurements compared both types of
cooling regimes and the cooling of scale-free surfaces and oxidized
surfaces. A numerical analysis was prepared to simulate the cooling
process with different conditions of the section and samples with
different oxide scale layers.
Abstract: Strong anion exchange resins with QN+OH-, have the
potential to be developed and employed as heterogeneous catalyst for
transesterification, as they are chemically stable to leaching of the
functional group. Nine different SIERs (SIER1-9) with QN+OH-were
prepared by suspension polymerization of vinylbenzyl chloridedivinylbenzene
(VBC-DVB) copolymers in the presence of n-heptane
(pore-forming agent). The amine group was successfully grafted into
the polymeric resin beads through functionalization with
trimethylamine. These SIERs are then used as a catalyst for the
transesterification of triacetin with methanol. A set of differential
equations that represents the Langmuir-Hinshelwood-Hougen-
Watson (LHHW) and Eley-Rideal (ER) models for the
transesterification reaction were developed. These kinetic models of
LHHW and ER were fitted to the experimental data. Overall, the
synthesized ion exchange resin-catalyzed reaction were welldescribed
by the Eley-Rideal model compared to LHHW models,
with sum of square error (SSE) of 0.742 and 0.996, respectively.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: The recommended limit for cadmium concentration in
potable water is less than 0.005 mg/L. A continuous biosorption
process using indigenous red seaweed, Gracilaria corticata, was
performed to remove cadmium from the potable water. The process
was conducted under fixed conditions and the breakthrough curves
were achieved for three consecutive sorption-desorption cycles. A
modeling based on Artificial Neural Network (ANN) was employed
to fit the experimental breakthrough data. In addition, a simplified
semi empirical model, Thomas, was employed for this purpose. It
was found that ANN well described the experimental data (R2>0.99)
while the Thomas prediction were a bit less successful with R2>0.97.
The adjusted design parameters using the nonlinear form of Thomas
model was in a good agreement with the experimentally obtained
ones. The results approve the capability of ANN to predict the
cadmium concentration in potable water.
Abstract: Cross flow water tube heat exchanger can be designed
and made operational using methods of model building and
simulation of the system. This paper projects the design and
development of a model of cross flow water tube heat-exchanger
system, simulation and validation of control analysis of different
tuning methods. Feedback and override control system is developed
using inputs acquired with the help of sensory system. A
mathematical model is formulated for analysis of system behaviour.
The temperature is regulated at the desired set point automatically.
Abstract: In this research, waterglass based aerogel powder was
prepared by sol–gel process and ambient pressure drying. Inspired by
limited dust releasing, aerogel powder was introduced to the PET
electrospinning solution in an attempt to create required bulk and
surface structure for the nanofibers to improve their hydrophobic and
insulation properties. The samples evaluation was carried out by
measuring density, porosity, contact angle, heat transfer, FTIR, BET,
and SEM. According to the results, porous silica aerogel powder was
fabricated with mean pore diameter of 24 nm and contact angle of
145.9º. The results indicated the usefulness of the aerogel powder
confined into nanofibers to control surface roughness for
manipulating superhydrophobic nanowebs with water contact angle
of 147º. It can be due to a multi-scale surface roughness which was
created by nanowebs structure itself and nanofibers surface
irregularity in presence of the aerogels while a layer of fluorocarbon
created low surface energy. The wettability of a solid substrate is an
important property that is controlled by both the chemical
composition and geometry of the surface. Also, a decreasing trend in
the heat transfer was observed from 22% for the nanofibers without
any aerogel powder to 8% for the nanofibers with 4% aerogel
powder. The development of thermal insulating materials has become
increasingly more important than ever in view of the fossil energy
depletion and global warming that call for more demanding energysaving
practices.