Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: Attitude Determination (AD) of a spacecraft using the
phase measurements of the Global Navigation Satellite System
(GNSS) is an active area of research. Various attitude determination
algorithms have been developed in yester years for spacecrafts using
different sensors but the last two decades have witnessed a
phenomenal increase in research related with GPS receivers as a
stand-alone sensor for determining the attitude of satellite using the
phase measurements of the signals from GNSS. The GNSS-based
Attitude determination algorithms have been experimented in many
real missions. The problem of AD algorithms using GNSS phase
measurements has two important parts; the ambiguity resolution and
the determining of attitude. Ambiguity resolution is the widely
addressed topic in literature for implementing the AD algorithm
using GNSS phase measurements for achieving the accuracy of
millimeter level. This paper broadly overviews the different
techniques for resolving the integer ambiguities encountered in AD
using GNSS phase measurements.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: Optimal load shedding (LS) design as an emergency plan is one of the main control challenges posed by emerging new uncertainties and numerous distributed generators including renewable energy sources in a modern power system. This paper presents an overview of the key issues and new challenges on optimal LS synthesis concerning the integration of wind turbine units into the power systems. Following a brief survey on the existing LS methods, the impact of power fluctuation produced by wind powers on system frequency and voltage performance is presented. The most LS schemas proposed so far used voltage or frequency parameter via under-frequency or under-voltage LS schemes. Here, the necessity of considering both voltage and frequency indices to achieve a more effective and comprehensive LS strategy is emphasized. Then it is clarified that this problem will be more dominated in the presence of wind turbines.
Abstract: In this paper, we are concerned with the design and
its simulation studies of a modified extremum seeking control for
nonlinear systems. A standard extremum seeking control has a simple
structure, but it takes a long time to reach an optimal operating point.
We consider a modification of the standard extremum seeking control
which is aimed to reach the optimal operating point more speedily
than the standard one. In the modification, PD acceleration term
is added before an integrator making a principal control, so that it
enables the objects to be regulated to the optimal point smoothly. This
proposed method is applied to Monod and Williams-Otto models to
investigate its effectiveness. Numerical simulation results show that
this modified method can improve the time response to the optimal
operating point more speedily than the standard one.
Abstract: Aurein 1.2 is a 13-residue amphipathic peptide with antibacterial and anticancer activity. Aurein1.2 and its retro analog were synthesized to study the activity of the peptides in relation to their structure. The antibacterial test result showed the retro-analog is inactive. The secondary structural analysis by CD spectra indicated that both of the peptides at TFE/Water adopt alpha-helical conformation. MD simulation was performed on aurein 1.2 and retro-analog in water and TFE in order to analyse the factors that are involved in the activity difference between retro and the native peptide. The simulation results are discussed and validated in the light of experimental data from the CD experiment. Both of the peptides showed a relatively similar pattern for their hydrophobicity, hydrophilicity, solvent accessible surfaces, and solvent accessible hydrophobic surfaces. However, they showed different in directions of dipole moment of peptides. Also, Our results further indicate that the reversion of the amino acid sequence affects flexibility .The data also showed that factors causing structural rigidity may decrease the activity. Consequently, our finding suggests that in the case of sequence-reversed peptide strategy, one has to pay attention to the role of amino acid sequence order in making flexibility and role of dipole moment direction in peptide activity. KeywordsAntimicrobial peptides, retro, molecular dynamic, circular dichroism.
Abstract: A person-to-person information sharing is easily realized
by P2P networks in which servers are not essential. Leakage
of information, which are caused by malicious accesses for P2P
networks, has become a new social issues. To prevent information
leakage, it is necessary to detect and block traffics of P2P software.
Since some P2P softwares can spoof port numbers, it is difficult to
detect the traffics sent from P2P softwares by using port numbers.
It is more difficult to devise effective countermeasures for detecting
the software because their protocol are not public.
In this paper, a discriminating method of network applications
based on communication characteristics of application messages
without port numbers is proposed. The proposed method is based
on an assumption that there can be some rules about time intervals
to transmit messages in application layer and the number of necessary
packets to send one message. By extracting the rule from network
traffic, the proposed method can discriminate applications without
port numbers.
Abstract: The purpose of the research was to determine
effectiveness of habilitation of preschool children with cerebral palsy
in the process of pedagogical support of their families. The author
presents the study of psychology-pedagogical problems of families
with preschool children with cerebral palsy and the universal
program of pedagogical support of families. In the conclusion, the
author determines effectiveness of social adaptation of children with
cerebral palsy and their families.
Abstract: Multi-user interference (MUI) is the main reason of system deterioration in the Spectral Amplitude Coding Optical Code Division Multiple Access (SAC-OCDMA) system. MUI increases with the number of simultaneous users, resulting into higher probability bit rate and limits the maximum number of simultaneous users. On the other hand, Phase induced intensity noise (PIIN) problem which is originated from spontaneous emission of broad band source from MUI severely limits the system performance should be addressed as well. Since the MUI is caused by the interference of simultaneous users, reducing the MUI value as small as possible is desirable. In this paper, an extensive study for the system performance specified by MUI and PIIN reducing is examined. Vectors Combinatorial (VC) codes families are adopted as a signature sequence for the performance analysis and a comparison with reported codes is performed. The results show that, when the received power increases, the PIIN noise for all the codes increases linearly. The results also show that the effect of PIIN can be minimized by increasing the code weight leads to preserve adequate signal to noise ratio over bit error probability. A comparison study between the proposed code and the existing codes such as Modified frequency hopping (MFH), Modified Quadratic- Congruence (MQC) has been carried out.
Abstract: A new code for spectral-amplitude coding optical
code-division multiple-access system is proposed called Random
diagonal (RD) code. This code is constructed using code segment and
data segment. One of the important properties of this code is that the
cross correlation at data segment is always zero, which means that
Phase Intensity Induced Noise (PIIN) is reduced. For the performance
analysis, the effects of phase-induced intensity noise, shot noise, and
thermal noise are considered simultaneously. Bit-error rate (BER)
performance is compared with Hadamard and Modified Frequency
Hopping (MFH) codes. It is shown that the system using this new
code matrices not only suppress PIIN, but also allows larger number
of active users compare with other codes. Simulation results shown
that using point to point transmission with three encoded channels,
RD code has better BER performance than other codes, also its found
that at 0 dbm PIIN noise are 10-10 and 10-11 for RD and MFH
respectively.
Abstract: A way of achieving nanodimentional structural elements in high carbon steel by special kind of heat treatment and cold plastic deformation is being explored. This leads to increasing interlamellar spacing of ferrite-carbide mixture. Decreasing the interlamellar spacing with cooling temperature increasing is determined. Experiments confirm such interlamellar spacing with which high carbon steel demonstrates the highest treatment and hardening capability. Total deformation degree effect on interlamellar spacing value in a ferrite-carbide mixture is obtained. Mechanical experiments results show that high carbon steel after heat treatment and repetitive cold plastic deformation possesses high tensile strength and yield strength keeping good percentage elongation.
Abstract: Transcription factor p53 has a powerful tumor
suppressing function that is associated with many cancers. However,
p53 of the molecular weight was higher make the limitation across to
skin or cell membrane. Thymidine dinucleotide (pTT), an
oligonucleotide, can activate the p53 transcription factor. pTT is a
hydrophilic and negative charge oligonucleotide, which delivery in to
cell membrane need an appropriate carrier. The aim of this study was
to improve the bioavailability of the nucleotide fragment, thymidine
dinucleotide (pTT), using elasic liposome carriers to deliver the drug
into the skin. The study demonstrate that dioleoylphosphocholine
(DOPC) incorporated with sodium cholate at molar ratio 1:1 can
archived the particle size about 220 nm. This elastic liposome could
penetration through skin from stratum corneum to whole epidermis by
confocal laser scanning microscopy (CLSM). Moreover, we observed
the the slight increase in generation of p53 by western blot.
Abstract: A chord of a simple polygon P is a line segment [xy]
that intersects the boundary of P only at both endpoints x and y. A
chord of P is called an interior chord provided the interior of [xy] lies
in the interior of P. P is weakly visible from [xy] if for every point v
in P there exists a point w in [xy] such that [vw] lies in P. In this
paper star-shaped, L-convex, and convex polygons are characterized
in terms of weak visibility properties from internal chords and starshaped
subsets of P. A new Krasnoselskii-type characterization of
isothetic star-shaped polygons is also presented.
Abstract: The field research was carried out at the Látókép AGTC KIT research area of the University of Debrecen in Eastern-Hungary, on the area of the aeolain loess of the Hajdúság. We examined the effects of the sowing time on the phytopathogenic characteristics and yield production by applying various fertilizer treatments on two different sunflower genotypes (NK Ferti, PR64H42) in 2012 and 2013. We applied three different sowing times (early, optimal, late) and two different treatment levels of fungicides (control = no fungicides applied, double fungicide protection).
During our investigations, the studied cropyears were of different sowing time optimum in terms of yield amount (2012: early, 2013: average). By Pearson’s correlation analysis, we have found that delaying the sowing time pronouncedly decreased the extent of infection in both crop years (Diaporthe: r=0.663**, r=0.681**, Sclerotinia: r=0.465**, r=0.622**). The fungicide treatment not only decreased the extent of infection, but had yield increasing effect too (2012: r=0.498**, 2013: r=0.603**). In 2012, delaying of the sowing time increased (r=0.600**), but in 2013, it decreased (r= 0.356*) the yield amount.
Abstract: In this paper, we have focused on study of swelling kinetics and salt-sensitivity behavior of a superabsorbing hydrogel based on carboxymethylcellulose (CMC) and acrylic acid and 2- Buthyl methacrylate. The swelling kinetics of the hydrogels with various particle sizes was preliminary investigated as well. The swelling of the hydrogel showed a second order kinetics of swelling in water. In addition, swelling measurements of the synthesized hydrogels in various chloride salt solutions was measured. Results indicated that a swelling-loss with an increase in the ionic strength of the salt solutions.
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Kavar-
Maharloo plains in Fars plain were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 17 meters during
1995 to 2006. The purpose of this study is to evaluate water level
changes in the Kavar-Maharloo Aquifer in the Fars province in order
to determine the areas of greatest depletion, the cause of depletion,
and predict the remaining life of the aquifer.
Abstract: Vibration of thin cylindrical shells made of a
functionally gradient material composed of stainless steel and nickel
is presented. The effects of the FGM configuration are studied by
studying the frequencies of FG cylindrical shells. In this case FG
cylindrical shell has Nickel on its outer surface and stainless steel on
its inner surface. The study is carried out based on third order shear
deformation shell theory. The objective is to study the natural
frequencies, the influence of constituent volume fractions and the
effects of configurations of the constituent materials on the
frequencies. The properties are graded in the thickness direction
according to the volume fraction power-law distribution. Results are
presented on the frequency characteristics, the influence of the
constituent various volume fractions on the frequencies.
Abstract: This paper deals with e-government issues at several
levels. Initially we look at the concept of e-government itself in order
to give it a sound framework. Than we look at the e-government
issues at three levels, first we analyse it at the global level, second we
analyse it at the level of transition economies, and finally we take a
closer look on developments in Croatia. The analysis includes actual
progress being made in selected transition economies given the Euro
area averages, along with e-government potential in future
demanding period.
Abstract: Explosive forming is one of the unconventional
techniques in which, most commonly, the water is used as the
pressure transmission medium. One of the newest methods in
explosive forming is gas detonation forming which uses a normal
shock wave derived of gas detonation, to form sheet metals. For this
purpose a detonation is developed from the reaction of H2+O2
mixture in a long cylindrical detonation tube. The detonation wave
goes through the detonation tube and acts as a blast load on the steel
blank and forms it. Experimental results are compared with a finite
element model; and the comparison of the experimental and
numerical results obtained from strain, thickness variation and
deformed geometry is carried out. Numerical and experimental
results showed approximately 75 – 90 % similarity in formability of
desired shape. Also optimum percent of gas mixture obtained when
we mix 68% H2 with 32% O2.
Abstract: Improvement in CAE methods has an important role for shortening of the vehicle product development time. It is provided that validation of the design and improvements in terms of durability can be done without hardware prototype production. In recent years, several different methods have been developed in order to investigate fatigue damage of the vehicle. The intended goal among these methods is prediction of fatigue damage in a short time with reduced costs. This study developed a new fatigue damage prediction method in the automotive sector using power spectrum densities of accelerations. This study also confirmed that the weak region in vehicle can be easily detected with the method developed in this study which results were compared with conventional method.