Abstract: The ability of pomelo peel, a natural biosorbent, to remove Cd(II) ions from aqueous solution by biosorption was investigated. The experiments were carried out by batch method at 25 °C. The influence of solution pH, initial cadmium ion concentrations and contact times were evaluated. Cadmium ion removal increased significantly as the pH of the solution increased from pH 1 to pH 5. At pH 5, the cadmium ion removal reached a maximum value. The equilibrium process was described well by the Langmuir isotherm model, with a maximum biosorption capacity of 21.83 mg/g. The biosorption was relatively quick, (approx. 20 min). Biosorption kinetics followed a pseudo-second-order model. The result showed that pomelo peel was effective as a biosorbent for removing cadmium ions from aqueous solution. It is a low cost material that shows potential to be applied in wastewater technology for remediation of heavy metal contamination.
Abstract: In this article we address the problem of mobile robot formation control. Indeed, the most work, in this domain, have studied extensively classical control for keeping a formation of mobile robots. In this work, we design an FLC (Fuzzy logic Controller) controller for separation and bearing control (SBC). Indeed, the leader mobile robot is controlled to follow an arbitrary reference path, and the follower mobile robot use the FSBC (Fuzzy Separation and Bearing Control) to keep constant relative distance and constant angle to the leader robot. The efficiency and simplicity of this control law has been proven by simulation on different situation.
Abstract: The study entitled “The Construction of Interactive
Computer Multimedia Instruction on Basic Japanese Vocabulary"
was aimed: 1) To construct the interactive computer multimedia
instruction on Basic Japanese Vocabulary, 2) To find out
multimedia-s quality, 3) To examine the student-s satisfaction and 4)
To study the learning achievement in Basic Japanese vocabulary. The
sampling group used in this study was composed of 40 1st year
student in Educational Communications and Technology Department,
Faculty of Industrial Education and Technology, King Mongkut-s
University of Technology Thonburi, in the academic year 2553 B.E.
(2010). According to research results, we found that 1). The quality
assessment by 3 mass media experts was at 4.72 on average or at high
level. 2) In terms of contents, the evaluation by 3 experts was at 4.81
on average or at high level. 3) In terms of achievement, there was a
statistical significance between before and after the treatment at the
.05 level. 4) The satisfaction of students towards the interactive
computer multimedia Instruction on “Basic Japanese Vocabulary"
was 4.35 on average, or at high level.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: This paper presents a smart-card applet that is able to
verify X.509 certificates and to use the public key contained in the
certificate for verifying digital signatures that have been created
using the corresponding private key, e.g. for the purpose of authenticating
the certificate owner against the card. The approach has been
implemented as an operating prototype on Java cards.
Abstract: The issue of classifying objects into one of predefined
groups when the measured variables are mixed with different types
of variables has been part of interest among statisticians in many
years. Some methods for dealing with such situation have been
introduced that include parametric, semi-parametric and nonparametric
approaches. This paper attempts to discuss on a problem
in classifying a data when the number of measured mixed variables is
larger than the size of the sample. A propose idea that integrates a
dimensionality reduction technique via principal component analysis
and a discriminant function based on the location model is discussed.
The study aims in offering practitioners another potential tool in a
classification problem that is possible to be considered when the
observed variables are mixed and too large.
Abstract: Calcium magnesium acetate (CMA) is environmentally
benign deicing chemicals that can replace sodium chloride that is
widely used on roads and highways at present for snow and ice control
to provide safe driving conditions during winter. The price of CMA
from petroleum-derived acetic acid is quite expensive. The bamboo
vinegar is the by-product from bamboo charcoal production. The
bamboo vinegar was used to prepare calcium acetate as raw materials,
and its deicing and corrosive performances were studied in this paper.
The results show that the freezing temperature of calcium acetate is
lower than that of sodium chloride when they have same molar
concentration, the deicing performance of calcium acetate is better
than that of sodium chloride when they have same moles, while the
deicing performance of sodium chloride is better than that of calcium
acetate. The corrosion of sodium chloride on iron-nail and steel-nail is
larger than that of calcium acetate whether they have same mass
concentration or same molar concentration, and the corrosion of
sodium chloride and calcium acetate on iron-nail is larger than that on
steel-nail, and calcium acetate almost hasn't corrosion on steel-nail.
Abstract: The tensile properties of Mg-3%Al nanocrystalline
alloys were investigated at different test environment. Bulk
nanocrystalline samples of these alloy was successfully prepared by
mechanical alloying (MA) followed by cold compaction, sintering,
and hot extrusion process. The crystal size of the consolidated milled
sample was calculated by X-Ray line profile analysis. The
deformation mechanism and microstructural characteristic at
different test condition was discussed extensively. At room
temperature, relatively lower value of activation volume (AV) and
higher value of strain rate sensitivity (SRS) suggests that new rate
controlling mechanism accommodating plastic flow in the present
nanocrystalline sample. The deformation behavior and the
microstructural character of the present samples were discussed in
details.
Abstract: The objectives of this research were to explore factors
influencing knowledge management process in the manufacturing
industry and develop a model to support knowledge management
processes. The studied factors were technology infrastructure, human
resource, knowledge sharing, and the culture of the organization. The
knowledge management processes included discovery, capture,
sharing, and application. Data were collected through questionnaires
and analyzed using multiple linear regression and multiple
correlation. The results found that technology infrastructure, human
resource, knowledge sharing, and culture of the organization
influenced the discovery and capture processes. However, knowledge
sharing had no influence in sharing and application processes. A
model to support knowledge management processes was developed,
which indicated that sharing knowledge needed further improvement
in the organization.
Abstract: Two species of Physalis, P.angulataL. and P.
peruviana L. were used as models for comparative study to
understand the values of micro-morphological, -anatomical and
architectural characteristics of leaf for taxonomic purposes and
possibly breeding and commercial applications. Both speciespossess
amphistomaticleaves with 1-layer epidermis, 3-4-layer spongy
mesophyll andbicollateral bundle midrib. Palisade parenchyma cells
of P. angulatawere almost twice longer (65-75 μm) than the other
one. Type of stomata was similar as anomocyticbut stomatal
index(SI) at adaxial surface and abaxial surface of P. angulata were
less than of P. peruvianaas 3.57, 4.00 and6.25, 6.66 respectively.
Some leaf architectural characteristics such as leaf shape, order of
venationalsoprovided information of taxonomic significance
Abstract: The paper presents a numerical investigation on the
rapid gas decompression in pure nitrogen which is made by using the
one-dimensional (1D) and three-dimensional (3D) mathematical
models of transient compressible non-isothermal fluid flow in pipes.
A 1D transient mathematical model of compressible thermal multicomponent
fluid mixture flow in pipes is presented. The set of the
mass, momentum and enthalpy conservation equations for gas phase
is solved in the model. Thermo-physical properties of multicomponent
gas mixture are calculated by solving the Equation of
State (EOS) model. The Soave-Redlich-Kwong (SRK-EOS) model is
chosen. This model is successfully validated on the experimental data
[1] and shows a good agreement with measurements. A 3D transient
mathematical model of compressible thermal single-component gas
flow in pipes, which is built by using the CFD Fluent code (ANSYS),
is presented in the paper. The set of unsteady Reynolds-averaged
conservation equations for gas phase is solved. Thermo-physical
properties of single-component gas are calculated by solving the Real
Gas Equation of State (EOS) model. The simplest case of gas
decompression in pure nitrogen is simulated using both 1D and 3D
models. The ability of both models to simulate the process of rapid
decompression with a high order of agreement with each other is
tested. Both, 1D and 3D numerical results show a good agreement
between each other. The numerical investigation shows that 3D CFD
model is very helpful in order to validate 1D simulation results if the
experimental data is absent or limited.
Abstract: We discuss the convergence property of the minimum residual (MINRES) method for the solution of complex shifted Hermitian system (αI + H)x = f. Our convergence analysis shows that the method has a faster convergence than that for real shifted Hermitian system (Re(α)I + H)x = f under the condition Re(α) + λmin(H) > 0, and a larger imaginary part of the shift α has a better convergence property. Numerical experiments show such convergence properties.
Abstract: Interpolated contour maps drawn for aluminum,
copper and molybdenum in downstream monitoring boreholes of
water dam in Miduk Copper Complex and the values of pH, redox
potential (Eh) and distance from water dam indicate different trends
of variation and behavior of these three elements in downward
groundwater resources. As these maps exhibit, aluminum is dominant
in the most alkaline (pH = 9-11) borehole (MB5) to water dam. The
highest concentration of molybdenum is found in the nearest
borehole (MB6) to water dam. Main concentration of copper is
observed in the most oxidized borehole (MB3 with Eh=293.2mV).
The spatial difference among sampling stations can be attributed to
the existence of faults and diaclases in the geologic structure of
Miduk region which causes the groundwater sampling sites to be
impressed by different contamination sources (toe seepage and upper
seepage water originated from different zones of tailings dump).
Abstract: In this paper we present a novel error model for
packet loss and subsequent error description. The proposed model
simulates the error performance of wireless communication link. The
model is designed as two independent Markov chains, where the first
one is used for packet generation and the second one generates
correctly and incorrectly transmitted bits for received packets from
the first chain. The statistical analyses of real communication on the
wireless link are used for determination of model-s parameters. Using
the obtained parameters and the implementation of the generator, we
collected generated traffic. The obtained results generated by
proposed model are compared with the real data collection.
Abstract: In a 10-week (May – August, 2008) Phase I trial, 840, 1+ rainbow trout, Oncorhynchus mykiss, received a commercial oral immunomodulator, Fin Immune™, at four different dosages (0, 10, 20 and 30 mg g-1) to evaluate immune response and growth. The overall objective of was to determine an optimal dosage of this product for rainbow trout that provides enhanced immunity with maximal growth and health. Biweekly blood samples were taken from 10 randomly selected fish in each tank (30 samples per treatment) to evaluate the duration of enhanced immunity conferred by Fin-Immune™. The immunological assessment included serum white blood cell (lymphocyte, neutrophil) densities and blood hematocrit (packed cell volume %). Of these three variables, only lymphocyte density increased significantly among trout fed Fin- Immune™ at 20 and 30 mg g-1 which peaked at week 6. At week 7, all trout were switched to regular feed (lacking Fin-Immune™) and by week 10, lymphocyte levels decreased among all levels but were still greater than at week 0. There was growth impairment at the highest dose of Fin-Immune™ tested (30 mg g-1) which can be associated with a physiological compensatory mechanism due to a dose-specific threshold level. Thus, our main objective of this Phase I study was achieved, the 20 mg g-1 dose of Fin-Immune™ should be the most efficacious (of those we tested) to use for a Phase II disease challenge trial.
Abstract: In view of growing competition in the service sector,
services are as much in need of modeling, analysis and improvement
as business or working processes. Graphical process models are
important means to capture process-related know-how for an
effective management of the service process. In this contribution, a
human performance analysis of process model development paying
special attention to model development time and the working method
was conducted. It was found that modelers with higher application
experience need significantly less time for mental activities than
modelers with lower application experience, spend more time on
labeling graphical elements, and achieved higher process model
quality in terms of activity label quality.
Abstract: This study was conducted to examine the effects of ketum extract on development of Chrysomya rufifacies and to analyze the presence of mitragynine in the larvae samples. 110 newly emerged first instar larvae of C. rufifacies were introduced on ketum extract-mixed cow liver at doses of 0, 20, 40 and 60g. Blowfly development rate was determined with 12 hour intervals and
mitragynine in larvae was extracted and quantitated. C. rufifacies in control group took about 192 hours to complete their development from first instar larvae to adult blowfly; meanwhile blowfly form from the highest dose of ketum was 264 hours. Mitragynine was detected in all groups of treatment, except for control. In conclusion, the presence of mitragynine in C. rufifacies is affected in delaying development rates of the blowfly for up to 62 hours or 3 days. Chemical analysis of mitragynine from larvae samples showed that this alkaloid present in all specimens analyzed.
Abstract: A method of collecting composition data and examining structural features of pearlite lamellae and the parent austenite at the growth interface in a 13wt. % manganese steel has been demonstrated with the use of Scanning Transmission Electron Microscopy (STEM). The combination of composition data and the structural features observed at the growth interface show that available theories of pearlite growth cannot explain all the observations.
Abstract: This paper presents a solution for a robotic
manipulation problem. We formulate the problem as combining
target identification, tracking and interception. The task in our
solution is sensing a target on a conveyor belt and then intercepting
robot-s end-effector at a convenient rendezvous point. We used
an object recognition method which identifies the target and finds
its position from visualized scene picture, then the robot system
generates a solution for rendezvous problem using the target-s initial
position and belt velocity . The interception of the target and the
end-effector is executed at a convenient rendezvous point along the
target-s calculated trajectory. Experimental results are obtained using
a real platform with an industrial robot and a vision system over it.
Abstract: Estimates of temperature values at a specific time of day, from daytime and daily profiles, are needed for a number of environmental, ecological, agricultural and technical applications, ranging from natural hazards assessments, crop growth forecasting to design of solar energy systems. The scope of this research is to investigate the efficiency of data mining techniques in estimating minimum, maximum and mean temperature values. For this reason, a number of experiments have been conducted with well-known regression algorithms using temperature data from the city of Patras in Greece. The performance of these algorithms has been evaluated using standard statistical indicators, such as Correlation Coefficient, Root Mean Squared Error, etc.