Abstract: An active suspension system has been proposed to
improve the ride comfort. A quarter-car 2 degree-of-freedom (DOF)
system is designed and constructed on the basis of the concept of a
four-wheel independent suspension to simulate the actions of an
active vehicle suspension system. The purpose of a suspension
system is to support the vehicle body and increase ride comfort. The
aim of the work described in the paper was to illustrate the
application of fuzzy logic technique to the control of a continuously
damping automotive suspension system. The ride comfort is
improved by means of the reduction of the body acceleration caused
by the car body when road disturbances from smooth road and real
road roughness.
The paper describes also the model and controller used in the
study and discusses the vehicle response results obtained from a
range of road input simulations. In the conclusion, a comparison of
active suspension fuzzy control and Proportional Integration
derivative (PID) control is shown using MATLAB simulations.
Abstract: The abundance and availability of rice husk, an agricultural waste, make them as a good source for precursor of activated carbon. In this work, rice husk-based activated carbons were prepared via base treated chemical activation process prior the carbonization process. The effect of carbonization temperatures (400, 600 and 800oC) on their pore structure was evaluated through morphology analysis using scanning electron microscope (SEM). Sample carbonized at 800oC showed better evolution and development of pores as compared to those carbonized at 400 and 600oC. The potential of rice husk-based activated carbon as an alternative adsorbent was investigated for the removal of Ni(II), Zn(II) and Pb(II) from single metal aqueous solution. The adsorption studies using rice husk-based activated carbon as an adsorbent were carried out as a function of contact time at room temperature and the metal ions were analyzed using atomic absorption spectrophotometer (AAS). The ability to remove metal ion from single metal aqueous solution was found to be improved with the increasing of carbonization temperature. Among the three metal ions tested, Pb(II) ion gave the highest adsorption on rice husk-based activated carbon. The results obtained indicate the potential to utilize rice husk as a promising precursor for the preparation of activated carbon for removal of heavy metals.
Abstract: This preliminary study attempts to see if a learning
environment influences instructor’s teaching strategies and learners’
in-class activities in a foreign language class at a university in Japan.
The class under study was conducted in a computer room, while the
majority of classes of the same course were offered in traditional
classrooms without computers. The study also sees if the unplanned
blended learning environment, enhanced, or worked against, in
achieving course goals, by paying close attention to in-class artefacts,
such as computers. In the macro-level analysis, the course syllabus
and weekly itinerary of the course were looked at; and in the microlevel
analysis, nonhuman actors in their environments were named
and analyzed to see how they influenced the learners’ task processes.
The result indicated that students were heavily influenced by the
presence of computers, which lead them to disregard some aspects of
intended learning objectives.
Abstract: As product life cycle becomes less and less every day,
having flexible manufacturing processes for any companies seems more demanding. In the assembling of closures, i.e. opening parts in
car body, hemming process is the one which needs more attention. This paper focused on the robot roller hemming process and how to
reduce its cycle time by introducing a fast roller hemming process. A
robot roller hemming process of a tailgate of Saab 93 SportCombi
model is investigated as a case study in this paper. By applying task
separation, robot coordination, and robot cell configuration principles in the roller hemming process, three alternatives are
proposed, developed, and remarkable reduction in cycle times achieved [1].
Abstract: In this paper the Differential Quadrature Method (DQM) is employed to study the coupled lateral-torsional free vibration behavior of the laminated composite beams. In such structures due to the fiber orientations in various layers, the lateral displacement leads to a twisting moment. The coupling of lateral and torsional vibrations is modeled by the bending-twisting material coupling rigidity. In the present study, in addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies of the beam. The governing differential equations of motion which form a system of three coupled PDEs are solved numerically using DQ procedure under different boundary conditions consist of the combinations of simply, clamped, free and other end conditions. The resulting natural frequencies and mode shapes for cantilever beam are compared with similar results in the literature and good agreement is achieved.
Abstract: Recent articles have addressed the problem to construct the confidence intervals for the mean of a normal distribution where the parameter space is restricted, see for example Wang [Confidence intervals for the mean of a normal distribution with restricted parameter space. Journal of Statistical Computation and Simulation, Vol. 78, No. 9, 2008, 829–841.], we derived, in this paper, analytic expressions of the coverage probability and the expected length of confidence interval for the normal mean when the whole parameter space is bounded. We also construct the confidence interval for the normal variance with restricted parameter for the first time and its coverage probability and expected length are also mathematically derived. As a result, one can use these criteria to assess the confidence interval for the normal mean and variance when the parameter space is restricted without the back up from simulation experiments.
Abstract: The objective of this research seeks to transmit a distance training model to the community in the upper northeastern region. The group sampling consists of 60 community leaders in the municipality of sub-district Kumphawapi, Kumphawapi Disrict, Udonthani Province. The research tools rely on the following instruments, they are : 1) the achievement test of community leaders- training and 2) the satisfaction questionnaires of community leaders. The statistics used in data analysis takes the statistical mean, percentage, standard deviation, and statistical T-test. The resulted findings reveal : 1) the efficiency of the distance training developed by the researcher for the community leaders joining in the training received the average score between in-training and post-training period higher than the setup criterion, 2) the two groups of participants in the training achieved higher knowledge than their pre-training state, 3) the comparison of the achievements between the two group presented no different results, 4) the community leaders obtained the high-to-highest satisfaction.
Abstract: In this paper, we present a method named Signal Level
Matrix (SLM) which can improve the accuracy and stability of active
RFID indoor positioning system. Considering the accuracy and cost,
we use uniform distribution mode to set up and separate the
overlapped signal covering areas, in order to achieve preliminary
location setting. Then, based on the proposed SLM concept and the
characteristic of the signal strength value that attenuates as the
distance increases, this system cross-examines the distribution of
adjacent signals to locate the users more accurately. The experimental
results indicate that the adaptive positioning method proposed in this
paper could improve the accuracy and stability of the positioning
system effectively and satisfyingly.
Abstract: The vibrations produced by a single point defect on
various parts of the bearing under constant radial load are predicted
by using a theoretical model. The model includes variation in the
response due to the effect of bearing dimensions, rotating frequency
distribution of load. The excitation forces are generated when the
defects on the races strike to rolling elements. In case of the outer
ring defect, the pulses generated are with periodicity of outer ring
defect frequency where as for inner ring defect, the pulses are with
periodicity of inner ring defect frequency. The effort has been carried
out in preparing the physical model of the system. Different defect
frequencies are obtained and are used to find out the amplitudes of
the vibration due to excitation of the bearing parts. Increase in the
radial load or severity of the defect produces a significant change in
bearing signature characteristics.
Abstract: The recent growth of using multimedia transmission
over wireless communication systems, have challenges to protect the
data from lost due to wireless channel effect. Images are corrupted
due to the noise and fading when transmitted over wireless channel,
in wireless channel the image is transmitted block by block, Due to
severe fading, entire image blocks can be damaged. The aim of this
paper comes out from need to enhance the digital images at the
wireless receiver side. Proposed Boundary Interpolation (BI)
Algorithm using wavelet, have been adapted here used to
reconstruction the lost block in the image at the receiver depend on
the correlation between the lost block and its neighbors. New
Proposed technique by using Boundary Interpolation (BI) Algorithm
using wavelet with Pixel interleaver has been implemented. Pixel
interleaver work on distribute the pixel to new pixel position of
original image before transmitting the image. The block lost through
wireless channel is only effects individual pixel. The lost pixels at the
receiver side can be recovered by using Boundary Interpolation (BI)
Algorithm using wavelet. The results showed that the New proposed
algorithm boundary interpolation (BI) using wavelet with pixel
interleaver is better in term of MSE and PSNR.
Abstract: This contribution deals with the relationship between
communication effectiveness and the extent of communication
among organizational units. To facilitate communication between
employees and to increase the level of understanding, the knowledge
of communication tools is necessary. Recent experience has shown
that personal communication is critical for smooth running of
companies and cannot be fully replaced by any form of technical
communication devices.
Below are presented the outcomes of the research on the
relationship between the extent of communication among
organisational units and its efficiency.
Abstract: To support user mobility for a wireless network new mechanisms are needed and are fundamental, such as paging, location updating, routing, and handover. Also an important key feature is mobile QoS offered by the WATM. Several ATM network protocols should be updated to implement mobility management and to maintain the already ATM QoS over wireless ATM networks. A survey of the various schemes and types of handover is provided. Handover procedure allows guarantee the terminal connection reestablishment when it moves between areas covered by different base stations. It is useful to satisfy user radio link transfer without interrupting a connection. However, failure to offer efficient solutions will result in handover important packet loss, severe delays and degradation of QoS offered to the applications. This paper reviews the requirements, characteristics and open issues of wireless ATM, particularly with regard to handover. It introduces key aspects of WATM and mobility extensions, which are added in the fixed ATM network. We propose a flexible approach for handover management that will minimize the QoS deterioration. Functional entities of this flexible approach are discussed in order to achieve minimum impact on the connection quality when a MT crosses the BS.
Abstract: Due to the fast development of technology, the
competition of technological products is turbulent; therefore, it is
important to understand the market trend, consumers- demand and
preferences. As the smartphones are prevalent, the main purpose of
this paper is to utilize Analytic Hierarchy Process (AHP) to analyze
consumer-s purchase evaluation factors of smartphones. Through the
AHP expert questionnaire, the smartphones- main functions are
classified as “user interface", “mobile commerce functions",
“hardware and software specifications", “entertainment functions" and
“appearance and design", five aspects to analyze the weights. Then
four evaluation criteria are evaluated under each aspect to rank the
weights. Based on an analysis of data shows that consumers consider
when purchase factors are “hardware and software specifications",
“user interface", “appearance and design", “mobile commerce
functions" and “entertainment functions" in sequence. The “hardware
and software specifications" aspect obtains the weight of 33.18%; it is
the most important factor that consumers are taken into account. In
addition, the most important evaluation criteria are central processing
unit, operating system, touch screen, and battery function in sequence.
The results of the study can be adopted as reference data for mobile
phone manufacturers in the future on the design and marketing
strategy to satisfy the voice of customer.
Abstract: A Variable Structure Model Reference Adaptive Controller using state variables is proposed for a class of multi input-multi output systems. Adaptation law is of variable structure type and switching functions is designed based on stability requirements. Global exponential stability is proved based on Lyapunov criterion. Transient behavior is analyzed using sliding mode control and shows perfect model following at a finite time.
Abstract: This study aims to investigate mechanical behavior of
deep-drawn cups consisting of aluminum (A1050)/ duralumin
(A2017) multi-layered clad structures with micro- and macro-scale
functional gradients. Such multi-layered clad structures are possibly
used for a new type of crash-boxes in automobiles to effectively
absorb the impact forces generated when automobiles having
collisions. The effect of heat treatments on microstructure,
compositional gradient, micro hardness in 2 and 6-layered aluminum/
duralumin clad structures, which were fabricated by hot rolling, have
been investigated. Impact compressive behavior of deep-drawn cups
consisting of such aluminum/ duralumin clad structures has been also
investigated in terms of energy absorption and maximum force.
Deep-drawn cups consisting of 6-layerd clad structures with microand
macro-scale functional gradients exhibit superior properties in
impact compressive tests.
Abstract: This paper compares the search engine marketing
strategies adopted in China and the Western countries through two illustrative cases, namely, Google and Baidu. Marketers in the West
use search engine optimization (SEO) to rank their sites higher for
queries in Google. Baidu, however, offers paid search placement, or the selling of engine results for particular keywords to the higher
bidders. Whereas Google has been providing innovative services ranging from Google Map to Google Blog, Baidu remains focused on
search services – the one that it does best. The challenges and
opportunities of the Chinese Internet market offered to global entrepreneurs are also discussed in the paper
Abstract: This paper presents part of a research into the small
scale modelling of masonry. Small scale testing of masonry has been
carried out by many authors, but few have attempted a systematic
determination of the parameters that affect masonry at a small scale.
The effect of increasing mortar strength and different sand gradings
under compression were investigated. The results show masonry
strength at small scale is influenced by increasing mortar strength and
different sand gradings.
Abstract: QoS Routing aims to find paths between senders and
receivers satisfying the QoS requirements of the application which
efficiently using the network resources and underlying routing
algorithm to be able to find low-cost paths that satisfy given QoS
constraints. The problem of finding least-cost routing is known to be
NP hard or complete and some algorithms have been proposed to
find a near optimal solution. But these heuristics or algorithms either
impose relationships among the link metrics to reduce the complexity
of the problem which may limit the general applicability of the
heuristic, or are too costly in terms of execution time to be applicable
to large networks. In this paper, we analyzed two algorithms namely
Characterized Delay Constrained Routing (CDCR) and Optimized
Delay Constrained Routing (ODCR). The CDCR algorithm dealt an
approach for delay constrained routing that captures the trade-off
between cost minimization and risk level regarding the delay
constraint. The ODCR which uses an adaptive path weight function
together with an additional constraint imposed on the path cost, to
restrict search space and hence ODCR finds near optimal solution in
much quicker time.
Abstract: Small signal stability causes small perturbations in the
generator that can cause instability in the power network. It is
generally known that small signal stability are directly related to the
generator and load properties. This paper examines the effects of
generator input variations on power system oscillations for a small
signal stability study. Eigenvaules and eigenvectors are used to
examine the stability of the power system. The dynamic power
system's mathematical model is constructed and thus calculated using
load flow and small signal stability toolbox on MATLAB. The power
system model is based on a 3-machine 9-bus system that was
modified to suit this study. In this paper, Participation Factors are a
means to gauge the effects of variation in generation with other
parameters on the network are also incorporated.
Abstract: The research titled “Developing of Thai Classical Music Ensemble in Rattanakosin Period" aimed 1) to study the history of Thai Classical Music Ensemble in Rattanakosin Period and 2) to analyze changing in each period of Rattanakosin Era. This is the historical and documentary research. The data was collected by in-depth interview those musicians, and academic music experts and field study. The focus group discussion was conducted to analyze and conclude the findings. The research found that the history of Thai Classical Music Ensemble in Rattanakosin Period derived from the Ayutthaya period. Thai classical music ensemble consisted of “Wong Pipat", “Wong Mahori", “Wong Kreang Sai". “Wong Kubmai", “Wong Krongkak", “Brass Band", and “Kan Band" which were used to ceremony, ritual, drama, performs and entertainment. Changed of the Thai music in the early Rattanakosin Period were passed from the Ayutthaya Period and the influence of the western civilization. New Band formed in Thai Music were “Orchestra" and “Contemporary Band". The role of Thai music was changed from the ceremonial rituals to entertainment. Development of the Thai music during the reign of King Rama 1 to King Rama 7, was improved from the court. But after the revolution, the musical patronage of the court was maintained by the Government. Thai Classical Music Ensemble were performed to be standard pattern.