Abstract: Direct and indirect somatic embryogenesis (SE) from
petiole and leaf explants of Scaevola aemula R. Br. cv. 'Purple
Fanfare' was achieved. High frequency of somatic embryos was
obtained directly from petiole and leaf explants using an inductive
plant growth regulator signal thidiazuron (TDZ). Petiole explants
were more responsive to SE than leaves. Plants derived from somatic
embryos of petiole explants germinated more readily into plants. SE
occurred more efficiently in half-strength Murashige and Skoog
(MS) medium than in full-strength MS medium. Non-embryogenic
callus induced by 2, 4-dichlorophenoxyacetic acid was used to
investigate the feasibility of obtaining SE with TDZ as a secondary
inductive plant growth regulator (PGR) signal. Non-embryogenic
callus of S. aemula was able to convert into an “embryogenic
competent mode" with PGR signal. Protocol developed for induction
of direct and indirect somatic embryogenesis in S. aemula can
improve the large scale propagation system of the plant in future.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: The third generation (3G) of cellular system adopted
the spread spectrum as solution for the transmission of the data in the
physical layer. Contrary to systems IS-95 or CDMAOne (systems
with spread spectrum of the preceding generation), the new standard,
called Universal Mobil Telecommunications System (UMTS), uses
long codes in the down link. The system is conceived for the vocal
communication and the transmission of the data. In particular, the
down link is very important, because of the asymmetrical request of
the data, i.e., more remote loading towards the mobiles than towards
the basic station. Moreover, the UMTS uses for the down link an
orthogonal spreading out with a variable factor of spreading out
(OVSF for Orthogonal Variable Spreading Factor). This
characteristic makes it possible to increase the flow of data of one or
more users by reducing their factor of spreading out without
changing the factor of spreading out of other users. In the current
standard of the UMTS, two techniques to increase the performances
of the down link were proposed, the diversity of sending antenna and
the codes space-time. These two techniques fight only fainding. The
receiver proposed for the mobil station is the RAKE, but one can
imagine a receiver more sophisticated, able to reduce the interference
between users and the impact of the coloured noise and interferences
to narrow band. In this context, where the users have long codes
synchronized with variable factor of spreading out and ignorance by
the mobile of the other active codes/users, the use of the sequences of
code pseudo-noises different lengths is presented in the form of one
of the most appropriate solutions.
Abstract: Quality control charts are very effective in detecting
out of control signals but when a control chart signals an out of
control condition of the process mean, searching for a special cause
in the vicinity of the signal time would not always lead to prompt
identification of the source(s) of the out of control condition as the
change point in the process parameter(s) is usually different from the
signal time. It is very important to manufacturer to determine at what
point and which parameters in the past caused the signal. Early
warning of process change would expedite the search for the special
causes and enhance quality at lower cost. In this paper the quality
variables under investigation are assumed to follow a multivariate
normal distribution with known means and variance-covariance
matrix and the process means after one step change remain at the new
level until the special cause is being identified and removed, also it is
supposed that only one variable could be changed at the same time.
This research applies artificial neural network (ANN) to identify the
time the change occurred and the parameter which caused the change
or shift. The performance of the approach was assessed through a
computer simulation experiment. The results show that neural
network performs effectively and equally well for the whole shift
magnitude which has been considered.
Abstract: A complex valued neural network is a neural network
which consists of complex valued input and/or weights and/or thresholds
and/or activation functions. Complex-valued neural networks
have been widening the scope of applications not only in electronics
and informatics, but also in social systems. One of the most important
applications of the complex valued neural network is in signal
processing. In Neural networks, generalized mean neuron model
(GMN) is often discussed and studied. The GMN includes a new
aggregation function based on the concept of generalized mean of all
the inputs to the neuron. This paper aims to present exhaustive results
of using Generalized Mean Neuron model in a complex-valued neural
network model that uses the back-propagation algorithm (called
-Complex-BP-) for learning. Our experiments results demonstrate the
effectiveness of a Generalized Mean Neuron Model in a complex
plane for signal processing over a real valued neural network. We
have studied and stated various observations like effect of learning
rates, ranges of the initial weights randomly selected, error functions
used and number of iterations for the convergence of error required on
a Generalized Mean neural network model. Some inherent properties
of this complex back propagation algorithm are also studied and
discussed.
Abstract: Support Vector Machine (SVM) is a statistical learning tool that was initially developed by Vapnik in 1979 and later developed to a more complex concept of structural risk minimization (SRM). SVM is playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM was applied to the detection of medical ultrasound images in the presence of partially developed speckle noise. The simulation was done for single look and multi-look speckle models to give a complete overlook and insight to the new proposed model of the SVM-based detector. The structure of the SVM was derived and applied to clinical ultrasound images and its performance in terms of the mean square error (MSE) metric was calculated. We showed that the SVM-detected ultrasound images have a very low MSE and are of good quality. The quality of the processed speckled images improved for the multi-look model. Furthermore, the contrast of the SVM detected images was higher than that of the original non-noisy images, indicating that the SVM approach increased the distance between the pixel reflectivity levels (detection hypotheses) in the original images.
Abstract: Image convolution similar to the receptive fields
found in mammalian visual pathways has long been used in
conventional image processing in the form of Gabor masks.
However, no VLSI implementation of parallel, multi-layered pulsed
processing has been brought forward which would emulate this
property. We present a technical realization of such a pulsed image
processing scheme. The discussed IC also serves as a general testbed
for VLSI-based pulsed information processing, which is of interest
especially with regard to the robustness of representing an analog
signal in the phase or duration of a pulsed, quasi-digital signal, as
well as the possibility of direct digital manipulation of such an
analog signal. The network connectivity and processing properties
are reconfigurable so as to allow adaptation to various processing
tasks.
Abstract: Independent component analysis (ICA) in the
frequency domain is used for solving the problem of blind source
separation (BSS). However, this method has some problems. For
example, a general ICA algorithm cannot determine the permutation
of signals which is important in the frequency domain ICA. In this
paper, we propose an approach to the solution for a permutation
problem. The idea is to effectively combine two conventional
approaches. This approach improves the signal separation
performance by exploiting features of the conventional approaches.
We show the simulation results using artificial data.
Abstract: A filter is used to remove undesirable frequency information from a dynamic signal. This paper shows that the Znotch filter filtering technique can be applied to remove the noise nuisance from a machining signal. In machining, the noise components were identified from the sound produced by the operation of machine components itself such as hydraulic system, motor, machine environment and etc. By correlating the noise components with the measured machining signal, the interested components of the measured machining signal which was less interfered by the noise, can be extracted. Thus, the filtered signal is more reliable to be analysed in terms of noise content compared to the unfiltered signal. Significantly, the I-kaz method i.e. comprises of three dimensional graphical representation and I-kaz coefficient, Z∞ could differentiate between the filtered and the unfiltered signal. The bigger space of scattering and the higher value of Z∞ demonstrated that the signal was highly interrupted by noise. This method can be utilised as a proactive tool in evaluating the noise content in a signal. The evaluation of noise content is very important as well as the elimination especially for machining operation fault diagnosis purpose. The Z-notch filtering technique was reliable in extracting noise component from the measured machining signal with high efficiency. Even though the measured signal was exposed to high noise disruption, the signal generated from the interaction between cutting tool and work piece still can be acquired. Therefore, the interruption of noise that could change the original signal feature and consequently can deteriorate the useful sensory information can be eliminated.
Abstract: This paper deals with the localization of the wideband sources. We develop a new approach for estimating the wide band sources parameters. This method is based on the high order statistics of the recorded data in order to eliminate the Gaussian components from the signals received on the various hydrophones.In fact the noise of sea bottom is regarded as being Gaussian. Thanks to the coherent signal subspace algorithm based on the cumulant matrix of the received data instead of the cross-spectral matrix the wideband correlated sources are perfectly located in the very noisy environment. We demonstrate the performance of the proposed algorithm on the real data recorded during an underwater acoustics experiments.
Abstract: In this paper, the signal transmission analysis of the
semicircle-shaped via structure for the differential pairs is presented in
the frequency range up to 10 GHz. In order to improve the signal
transmission properties in the differential pairs, single via is separated
centrally into two semicircle-shaped sections, which are
interconnected with the traces of differential pairs respectively. This
via structure make possible to route differential pairs using only one
via. In addition, it can improve impedance discontinuity around its
region and then enhance the signal transmission properties in the
differential pairs. The electrical analysis such as S-parameter
calculation and eye diagram simulation has been performed to
investigate the improvement of the signal transmission property in the
differential pairs with new via structure.
Abstract: There is increasing evidence that earthquakes produce electromagnetic signals observable at the surface in the extremely low to very low freqency (ELF - VLF) range often in advance to the main event. These precursors are candidates for prediction purposes. Laboratory experiments con´¼ürm that material under load emits an electromagnetic signature, the detailed generation mechanisms how- ever are not well understood yet.
Abstract: The development of the signal compression
algorithms is having compressive progress. These algorithms are
continuously improved by new tools and aim to reduce, an average,
the number of bits necessary to the signal representation by means of
minimizing the reconstruction error. The following article proposes
the compression of Arabic speech signal by a hybrid method
combining the wavelet transform and the linear prediction. The
adopted approach rests, on one hand, on the original signal
decomposition by ways of analysis filters, which is followed by the
compression stage, and on the other hand, on the application of the
order 5, as well as, the compression signal coefficients. The aim of
this approach is the estimation of the predicted error, which will be
coded and transmitted. The decoding operation is then used to
reconstitute the original signal. Thus, the adequate choice of the
bench of filters is useful to the transform in necessary to increase the
compression rate and induce an impercevable distortion from an
auditive point of view.
Abstract: It is sometimes difficult to differentiate between
innocent murmurs and pathological murmurs during auscultation. In
these difficult cases, an intelligent stethoscope with decision support
abilities would be of great value. In this study, using a dog model,
phonocardiographic recordings were obtained from 27 boxer dogs
with various degrees of aortic stenosis (AS) severity. As a reference
for severity assessment, continuous wave Doppler was used. The data
were analyzed with recurrence quantification analysis (RQA) with
the aim to find features able to distinguish innocent murmurs from
murmurs caused by AS. Four out of eight investigated RQA features
showed significant differences between innocent murmurs and
pathological murmurs. Using a plain linear discriminant analysis
classifier, the best pair of features (recurrence rate and entropy)
resulted in a sensitivity of 90% and a specificity of 88%. In
conclusion, RQA provide valid features which can be used for
differentiation between innocent murmurs and murmurs caused by
AS.
Abstract: MBMS is a unidirectional point-to-multipoint bearer
service in which data are transmitted from a single source entity to
multiple recipients. For a mobile to support the MBMS, MBMS client
functions as well as MBMS radio protocols should be designed and
implemented. In this paper, we analyze the MBMS client functions
and describe the implementation of them in our mobile test-bed. User
operations and signaling flows between protocol entities to control the
MBMS functions are designed in detail. Service announcement
utilizing the file download MBMS service and four MBMS user
services are demonstrated in the test-bed to verify the MBMS client
functions.
Abstract: Wireless ad hoc nodes are freely and dynamically
self-organize in communicating with others. Each node can act as
host or router. However it actually depends on the capability of
nodes in terms of its current power level, signal strength, number
of hops, routing protocol, interference and others. In this research,
a study was conducted to observe the effect of hops count over
different network topologies that contribute to TCP Congestion
Control performance degradation. To achieve this objective, a
simulation using NS-2 with different topologies have been
evaluated. The comparative analysis has been discussed based on
standard observation metrics: throughput, delay and packet loss
ratio. As a result, there is a relationship between types of topology
and hops counts towards the performance of ad hoc network. In
future, the extension study will be carried out to investigate the
effect of different error rate and background traffic over same
topologies.
Abstract: In this work, we present a comparison between two
techniques of image compression. In the first case, the image is
divided in blocks which are collected according to zig-zag scan. In
the second one, we apply the Fast Cosine Transform to the image,
and then the transformed image is divided in blocks which are
collected according to zig-zag scan too. Later, in both cases, the
Karhunen-Loève transform is applied to mentioned blocks. On the
other hand, we present three new metrics based on eigenvalues for a
better comparative evaluation of the techniques. Simulations show
that the combined version is the best, with minor Mean Absolute
Error (MAE) and Mean Squared Error (MSE), higher Peak Signal to
Noise Ratio (PSNR) and better image quality. Finally, new technique
was far superior to JPEG and JPEG2000.
Abstract: The paper presents a novel idea to control computer
mouse cursor movement with human eyes. In this paper, a working
of the product has been described as to how it helps the special
people share their knowledge with the world. Number of traditional
techniques such as Head and Eye Movement Tracking Systems etc.
exist for cursor control by making use of image processing in which
light is the primary source. Electro-oculography (EOG) is a new
technology to sense eye signals with which the mouse cursor can be
controlled. The signals captured using sensors, are first amplified,
then noise is removed and then digitized, before being transferred to
PC for software interfacing.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: The triumph of inductive neuro-stimulation since its rediscovery in the 1980s has been quite spectacular. In lots of branches ranging from clinical applications to basic research this system is absolutely indispensable. Nevertheless, the basic knowledge about the processes underlying the stimulation effect is still very rough and rarely refined in a quantitative way. This seems to be not only an inexcusable blank spot in biophysics and for stimulation prediction, but also a fundamental hindrance for technological progress. The already very sophisticated devices have reached a stage where further optimization requires better strategies than provided by simple linear membrane models of integrate-and-fire style. Addressing this problem for the first time, we suggest in the following text a way for virtual quantitative analysis of a stimulation system. Concomitantly, this ansatz seems to provide a route towards a better understanding by using nonlinear signal processing and taking the nerve as a filter that is adapted for neuronal magnetic stimulation. The model is compact and easy to adjust. The whole setup behaved very robustly during all performed tests. Exemplarily a recent innovative stimulator design known as cTMS is analyzed and dimensioned with this approach in the following. The results show hitherto unforeseen potentials.