Abstract: This research aims to analyze the regenerative burner and the recuperative burner for the different reheating furnaces in the steel industry. The warm air temperatures of the burners are determined to suit with the sizes of the reheating furnaces by considering the air temperature, the fuel cost and the investment cost. The calculations of the payback period and the net present value are studied to compare the burners for the different reheating furnaces. The energy balance is utilized to calculate and compare the energy used in the different sizes of reheating furnaces for each burner. It is found that the warm air temperature is different if the sizes of reheating furnaces are varied. Based on the considerations of the net present value and the payback period, the regenerative burner is suitable for all plants at the same life of the burner. Finally, the sensitivity analysis of all factors has been discussed in this research.
Abstract: This paper addresses the problem of the partial state
feedback stabilization of a class of nonlinear systems. In order to
stabilization this class systems, the especial place of this paper is
to reverse designing the state feedback control law from the method
of judging system stability with the center manifold theory. First of
all, the center manifold theory is applied to discuss the stabilization
sufficient condition and design the stabilizing state control laws for a
class of nonlinear. Secondly, the problem of partial stabilization for a
class of plane nonlinear system is discuss using the lyapunov second
method and the center manifold theory. Thirdly, we investigate specially
the problem of the stabilization for a class of homogenous plane
nonlinear systems, a class of nonlinear with dual-zero eigenvalues and
a class of nonlinear with zero-center using the method of lyapunov
function with homogenous derivative, specifically. At the end of this
paper, some examples and simulation results are given show that the
approach of this paper to this class of nonlinear system is effective
and convenient.
Abstract: The Inter feeder Power Flow Regulator (IFPFR)
proposed in this paper consists of several voltage source inverters
with common dc bus; each inverter is connected in series with one of
different independent distribution feeders in the power system. This
paper is concerned with how to transfer power between the feeders for
load sharing purpose. The power controller of each inverter injects
the power (for sending feeder) or absorbs the power (for receiving
feeder) via injecting suitable voltage; this voltage injection is
simulated by voltage drop across series virtual impedance, the
impedance value is selected to achieve the concept of power exchange
between the feeders without perturbing the load voltage magnitude of
each feeder. In this paper a new control scheme for load sharing using
IFPFR is proposed.
Abstract: This paper presents application artificial intelligent (AI) techniques, namely artificial neural network (ANN), adaptive neuro fuzzy interface system (ANFIS), to estimate the real power transfer between generators and loads. Since these AI techniques adopt supervised learning, it first uses modified nodal equation method (MNE) to determine real power contribution from each generator to loads. Then the results of MNE method and load flow information are utilized to estimate the power transfer using AI techniques. The 25-bus equivalent system of south Malaysia is utilized as a test system to illustrate the effectiveness of both AI methods compared to that of the MNE method. The mean squared error of the estimate of ANN and ANFIS power transfer allocation methods are 1.19E-05 and 2.97E-05, respectively. Furthermore, when compared to MNE method, ANN and ANFIS methods computes generator contribution to loads within 20.99 and 39.37msec respectively whereas the MNE method took 360msec for the calculation of same real power transfer allocation.
Abstract: Predicting short term wind speed is essential in order
to prevent systems in-action from the effects of strong winds. It also
helps in using wind energy as an alternative source of energy, mainly
for Electrical power generation. Wind speed prediction has
applications in Military and civilian fields for air traffic control,
rocket launch, ship navigation etc. The wind speed in near future
depends on the values of other meteorological variables, such as
atmospheric pressure, moisture content, humidity, rainfall etc. The
values of these parameters are obtained from a nearest weather
station and are used to train various forms of neural networks. The
trained model of neural networks is validated using a similar set of
data. The model is then used to predict the wind speed, using the
same meteorological information. This paper reports an Artificial
Neural Network model for short term wind speed prediction, which
uses back propagation algorithm.
Abstract: This paper is prepared to provide a review of how an automotive manufacturer, ISUZU HICOM Malaysia Co. Ltd. sustained the supply chain management after business process reengineering in 2007. One of the authors is currently undergoing industrial attachment and has spent almost 6 months researching in the production and operation management system of the company. This study was carried out as part of the tasks in the attachment program. The result shows that delivery lateness and outsourcing are the main barriers that affected productivity. From the gap analysis, the authors found that new business process operation had improved suppliers delivery performance.
Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: Evaluation and survey of curriculum quality as one of the most important components of universities system is necessary for different levels in higher education. The main purpose of this study was to survey of the curriculum quality of Actuarial science field. Case: University of SHahid Beheshti and Higher education institute of Eco insurance (according to viewpoint of students, alumni, employers and faculty members). Descriptive statistics (mean, tables, percentage, and frequency distribution) and inferential statistics (CHI SQUARE) were used to analyze the data. Six criteria considered for the Quality of curriculum: objectives, content, teaching and learning methods, space and facilities, Time, assessment of learning. Content, teaching and learning methods, space and facilities, assessment of learning criteria were relatively desirable level, objectives and time criterions were desirable level. The quality of curriculum of Actuarial Science field was relatively desirable level.
Abstract: Pretreatment of oil palm empty fruit bunch (OPEFB) with N-Methylmorpholine-N-oxide (NMMO) to enhance biogas production was investigated. The pretreatments were performed at 90 and 120ºC for 1, 3, and 5 h using three different concentrations of NMMO of 73%, 79%, and 85%. The pretreated OPEFB was subsequently anaerobically digested to produce biogas. After pretreatment, there were no significant changes of the main composition of OPEFB and the maximum total solid recovery was 92%. The amorphous phase was increased up to 78% at pretreatment condition using 85% NMMO solution for 3 h at 120oC. In general, higher concentration of NMMO and higher temperature resulted in increased amorphous form and higher biogas production. The best results of biogas production reached enhancement of methane yield of 148% compared to the untreated OPEFB and increased in digestion of 94% compared to starch as reference.
Abstract: Spatial trends are one of the valuable patterns in geo
databases. They play an important role in data analysis and
knowledge discovery from spatial data. A spatial trend is a regular
change of one or more non spatial attributes when spatially moving
away from a start object. Spatial trend detection is a graph search
problem therefore heuristic methods can be good solution. Artificial
immune system (AIS) is a special method for searching and
optimizing. AIS is a novel evolutionary paradigm inspired by the
biological immune system. The models based on immune system
principles, such as the clonal selection theory, the immune network
model or the negative selection algorithm, have been finding
increasing applications in fields of science and engineering.
In this paper, we develop a novel immunological algorithm based
on clonal selection algorithm (CSA) for spatial trend detection. We
are created neighborhood graph and neighborhood path, then select
spatial trends that their affinity is high for antibody. In an
evolutionary process with artificial immune algorithm, affinity of
low trends is increased with mutation until stop condition is satisfied.
Abstract: The Niger Delta Region of Nigeria is home to about
20 million people and 40 different ethnic groups. The region has an
area of seventy thousand square kilometers (70,000 KM2) of
wetlands, formed primarily by sediments deposition and makes up
7.5 percent of Nigeria's total landmass. The notable ecological zones
in this region includes: coastal barrier islands; mangrove swamp
forests; fresh water swamps; and lowland rainforests. This incredibly
naturally-endowed ecosystem region, which contains one of the
highest concentrations of biodiversity on the planet, in addition to
supporting abundant flora and fauna, is threatened by the inhuman act
known as gas flaring. Gas flaring is the combustion of natural gas
that is associated with crude oil when it is pumped up from the
ground. In petroleum-producing areas such as the Niger Delta region
of Nigeria where insufficient investment was made in infrastructure
to utilize natural gas, flaring is employed to dispose of this associated
gas. This practice has impoverished the communities where it is
practiced, with attendant environmental, economic and health
challenges. This paper discusses the adverse environmental and
health implication associated with the practice, the role of
Government, Policy makers, Oil companies and the Local
communities aimed at bring this inhuman practice to a prompt end.
Abstract: Planning the transition period for the adoption of
alternative fuel-technology powertrains is a challenging task that
requires sophisticated analysis tools. In this study, a system dynamic
approach was applied to analyze the bi-directional interaction
between the development of the refueling station network and vehicle
sales. Besides, the developed model was used to estimate the
transition cost to reach a predefined target (share of alternative fuel
vehicles) in different scenarios. Several scenarios have been analyzed
to investigate the effectiveness and cost of incentives on the initial
price of vehicles, and on the evolution of fuel and refueling stations.
Obtained results show that a combined set of incentives will be more
effective than just a single specific type of incentives.
Abstract: In this paper, the application of neural networks to study the design of short-term load forecasting (STLF) Systems for Illam state located in west of Iran was explored. One important architecture of neural networks named Multi-Layer Perceptron (MLP) to model STLF systems was used. Our study based on MLP was trained and tested using three years (2004-2006) data. The results show that MLP network has the minimum forecasting error and can be considered as a good method to model the STLF systems.
Abstract: Differentiated impact of team sports (basketball, indoor soccer, handball) on general haemodynamics and aerobic potential of students who specialize in technical subjects is detected only on the fourth year of studies in the institute of higher education. Those who play basketball and indoor soccer have shown increase of stroke and minute volume of blood indices, pumping and contractile function of the heart, oxygenation of blood and oxygen delivery to tissues, aerobic energy supply and balance of sympathetic and parasympathetic activity of the nervous regulation mechanism of the circulatory system. Those who play handball have shown these indices statistically decreased. On the whole playing basketball and indoor soccer optimizes the strategy for adaptation of students to the studying process, but playing handball does the opposite thing. The leading factor for adaptation of students is: those who play basketball have increase of minute blood volume which stipulates velocity of the system blood circulation and well-timed oxygen delivery to tissues; those who play indoor soccer have increase of power and velocity of contractile function of the heart; those who play handball have increase of resistance of thorax to the system blood flow which minimizes contractile function of the heart, blood oxygen saturation and delivery of oxygen to tissues.
Abstract: For numerical prediction of the NOX in the exhaust of
a compression ignition engine a model was developed by considering
the parameter equivalence ratio. This model was validated by
comparing the predicted results of NOX with experimental ones. The
ultimate aim of the work was to access the applicability, robustness
and performance of the improved NOX model against other NOX
models.
Abstract: The size, complexity and number of databases used
for protein information have caused bioinformatics to lag behind in
adapting to the need to handle this distributed information.
Integrating all the information from different databases into one
database is a challenging problem. Our main research is to develop a
tool which can be used to access and manipulate protein information
from difference databases. In our approach, we have integrated
difference databases such as Swiss-prot, PDB, Interpro, and EMBL
and transformed these databases in flat file format into relational
form using XML and Bioperl. As a result, we showed this tool can
search different sizes of protein information stored in relational
database and the result can be retrieved faster compared to flat file
database. A web based user interface is provided to allow user to
access or search for protein information in the local database.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: An optimal power flow (OPF) based on particle swarm
optimization (PSO) was developed with more realistic generator
security constraint using the capability curve instead of only Pmin/Pmax
and Qmin/Qmax. Neural network (NN) was used in designing digital
capability curve and the security check algorithm. The algorithm is
very simple and flexible especially for representing non linear
generation operation limit near steady state stability limit and under
excitation operation area. In effort to avoid local optimal power flow
solution, the particle swarm optimization was implemented with
enough widespread initial population. The objective function used in
the optimization process is electric production cost which is
dominated by fuel cost. The proposed method was implemented at
Java Bali 500 kV power systems contain of 7 generators and 20
buses. The simulation result shows that the combination of generator
power output resulted from the proposed method was more economic
compared with the result using conventional constraint but operated
at more marginal operating point.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.