Abstract: Novel nitrogen removal technologies via nitrite
pathway attract increasing interest in recent years. In this study,
batch experiments were performed to investigate nitrite accumulation
characteristics and shifts in nitrifying community structure at
different growth environments including ammonia concentration, pH
and alkalinity. It was found that nitrite accumulation ratios were
maintained at around 95% at studied conditions, and the optimum pH
and Alk/N (ratio between alkalinity and nitrogen) for ammonium
oxidization were 8.5 and 8.33, respectively. Fluorescence in situ
hybridization analysis of nitrifying bacteria showed that high free
ammonia (from influent ammonium or caused by high pH)
significantly altered the structure of nitrifying community, leading to
abundance of ammonia-oxidizing bacteria (AOB), especially
Nitrososmonas, and inhibition of nitrite-oxidizing bacteria (NOB).
The results suggest that free ammonia plays more important role than
other studied conditions on nitrite accumulation.
Abstract: A new approach to predict the 3D structures of proteins by combining the knowledge-based method and Molecular Dynamics Simulation is presented on the chicken villin headpiece subdomain (HP-36). Comparative modeling is employed as the knowledge-based method to predict the core region (Ala9-Asn28) of the protein while the remaining residues are built as extended regions (Met1-Lys8; Leu29-Phe36) which then further refined using Molecular Dynamics Simulation for 120 ns. Since the core region is built based on a high sequence identity to the template (65%) resulting in RMSD of 1.39 Å from the native, it is believed that this well-developed core region can act as a 'nucleation center' for subsequent rapid downhill folding. Results also demonstrate that the formation of the non-native contact which tends to hamper folding rate can be avoided. The best 3D model that exhibits most of the native characteristics is identified using clustering method which then further ranked based on the conformational free energies. It is found that the backbone RMSD of the best model compared to the NMR-MDavg is 1.01 Å and 3.53 Å, for the core region and the complete protein, respectively. In addition to this, the conformational free energy of the best model is lower by 5.85 kcal/mol as compared to the NMR-MDavg. This structure prediction protocol is shown to be effective in predicting the 3D structure of small globular protein with a considerable accuracy in much shorter time compared to the conventional Molecular Dynamics simulation alone.
Abstract: Advances in processors architecture, such as multicore,
increase the size of complexity of parallel computer systems.
With multi-core architecture there are different parallel languages
that can be used to run parallel programs. One of these languages is
OpenMP which embedded in C/Cµ or FORTRAN. Because of this
new architecture and the complexity, it is very important to evaluate
the performance of OpenMP constructs, kernels, and application
program on multi-core systems. Performance is the activity of
collecting the information about the execution characteristics of a
program. Performance tools consists of at least three interfacing
software layers, including instrumentation, measurement, and
analysis. The instrumentation layer defines the measured
performance events. The measurement layer determines what
performance event is actually captured and how it is measured by the
tool. The analysis layer processes the performance data and
summarizes it into a form that can be displayed in performance tools.
In this paper, a number of OpenMP performance tools are surveyed,
explaining how each is used to collect, analyse, and display data
collection.
Abstract: Increased energy demand and the concern about
environment friendly technology, renewable bio-fuels are better
alternative to petroleum products. In the present study linseed oil was
used as alternative source for diesel engine fuel and the results were
compared with baseline data of neat diesel. Performance parameters
such as brake thermal efficiency (BTE) and brake specific fuel
consumption (BSFC) and emissions parameters such as CO,
unburned hydro carbon (UBHC), NOx, CO2 and exhaust temperature
were compared. BTE of the engine was lower and BSFC was higher
when the engine was fueled with Linseed oil compared to diesel fuel.
Emission characteristics are better than diesel fuel. NOx formation by
using linseed oil during the experiment was lower than diesel fuel.
Linseed oil is non edible oil, so it can be used as an extender of diesel
fuel energy source for small and medium energy needs.
Abstract: The objective of this experiment was to study of water
relations and chlorophyll in different wheat genotypes and their
correlations with grain and biological yields. 21 genotypes of bread
wheat were compared in a field experiment as randomized complete
blocks design with four replications. The results showed that relative
water deficit, relative water loss, excised leaf water retention, cell
membrane stability, chlorophyll-a, chlorophyll-b, total chlorophyll,
grain yield and biological yield were different significantly among
wheat genotypes, but SPAD-chlorophyll index, relative water content
and chlorophyll florescence were not. Significant correlations were
not observed among above mentioned water relations and
chlorophyll characteristics with grain yield, but there was a positive
and significant correlation between biological yield and grain yield.
Abstract: This work proposes a set of actions to assist redesign
procedure in existing products of Electric and Electronic Equipment
(EEE). The aim is to improve their environmental behavior after their
withdrawal in the End-of-Life (EOL) phase. In the beginning data
collection takes place. Then follows selection and implementation of
the optimal EOL Treatment Strategy (EOL_TS) and its results-
evaluation concerning the environment. In parallel, product design
characteristics that can be altered are selected based on their
significance for the environment in the EOL stage. All results from
the previous stages are combined and possible redesign actions are
formulated for further examination and afterwards configuration in
the design stage. The applied method to perform these tasks is Lean
Thinking (LT). At the end, results concerning the application of the
proposed method on a distribution transformer are presented.
Abstract: The many feasible alternatives and conflicting
objectives make equipment selection in materials handling a
complicated task. This paper presents utilizing Monte Carlo (MC)
simulation combined with the Analytic Hierarchy Process (AHP) to
evaluate and select the most appropriate Material Handling
Equipment (MHE). The proposed hybrid model was built on the base
of material handling equation to identify main and sub criteria critical
to MHE selection. The criteria illustrate the properties of the material
to be moved, characteristics of the move, and the means by which the
materials will be moved. The use of MC simulation beside the AHP
is very powerful where it allows the decision maker to represent
his/her possible preference judgments as random variables. This will
reduce the uncertainty of single point judgment at conventional AHP,
and provide more confidence in the decision problem results. A small
business pharmaceutical company is used as an example to illustrate
the development and application of the proposed model.
Abstract: According to Rostler method (ASTM D 2006), saturates content of bitumen is determined based on its reactivity to sulphuric acid. While Corbett method (ASTM D 4124) based on its polarity level. This paper presents results from the study on the effect of saturates content determined by two different fractionation methods on the rheological and aging characteristics of bitumen. The result indicated that the increment of saturates content tended to reduce all the rheological characteristics concerned. Bitumen became less elastic, less viscous, and less resistant to plastic deformation, but became more resistant to fatigue cracking. After short and long term aging process, the treatment effect coefficients of saturates decreased, saturates became thicker due to aging process. This study concludes that saturates is not really stable or reactive in aging process. Therefore, the reactivity of saturates should be considered in bitumen aging index
Abstract: In this paper, a new design technique for enhancing
bandwidth that improves the performance of a conventional
microstrip patch antenna is proposed. This paper presents a novel
wideband probe fed inverted slotted microstrip patch antenna. The
design adopts contemporary techniques; coaxial probe feeding,
inverted patch structure and slotted patch. The composite effect of
integrating these techniques and by introducing the proposed patch,
offer a low profile, broadband, high gain, and low cross-polarization
level. The results for the VSWR, gain and co-and cross-polarization
patterns are presented. The antenna operating the band of 1.80-2.36
GHz shows an impedance bandwidth (2:1 VSWR) of 27% and a gain
of 10.18 dBi with a gain variation of 1.12 dBi. Good radiation
characteristics, including a cross-polarization level in xz-plane less
than -42 dB, have been obtained.
Abstract: In this paper, some experiments of liquid dispersion flow driven by explosion in vertical plane were carried out using a liquid explosive dispersion device with film cylindrical constraints. The separated time series describing the breakup shape and dispersion process of liquid were recorded with high speed CMOS camera. The experimental results were analyzed and some essential characteristics of liquid dispersing flow are presented.
Abstract: Recently, the Spherical Motion Models (SMM-s) have been introduced [1]. These new models have been developed for 3D local landmark-base Autonomous Navigation (AN). This paper is revealing new arguments and experimental results to support the SMM-s characteristics. The accuracy and the robustness in performing a specific task are the main concerns of the new investigations. To analyze their performances of the SMM-s, the most powerful tools of estimation theory, the extended Kalman filter (EKF) and unscented Kalman filter (UKF), which give the best estimations in noisy environments, have been employed. The Monte Carlo validation implementations used to test the stability and robustness of the models have been employed as well.
Abstract: Liners are made to protect the groundwater table from
the infiltration of leachate which normally carries different kinds of
toxic materials from landfills. Although these liners are engineered to
last for long period of time; unfortunately these liners fail; therefore,
toxic materials pass to groundwater. This paper focuses on the
changes of the hydraulic conductivity of a sand-bentonite liner due to
the infiltration of biofuel and ethanol fuel. Series of laboratory tests
were conducted in 20-cm-high PVC columns. Several compositions
of sand-bentonite liners were tested: 95% sand: 5% bentonite; 90%
sand: 10% bentonite; and 100% sand (passed mesh #40). The
columns were subjected to extreme pressures of 40 kPa, and 100 kPa
to evaluate the transport of alternative fuels (biofuel and ethanol
fuel). For comparative studies, similar tests were carried out using
water. Results showed that hydraulic conductivity increased due to
the infiltration of alternative fuels through the liners. Accordingly,
the increase in the hydraulic conductivity showed significant
dependency on the type of liner mixture and the characteristics of the
liquid. The hydraulic conductivity of a liner (subjected to biofuel
infiltration) consisting of 5% bentonite: 95% sand under pressure of
40 kPa and 100 kPa had increased by one fold. In addition, the
hydraulic conductivity of a liner consisting of 10% bentonite: 90%
sand under pressure of 40 kPa and 100 kPa and infiltrated by biofuel
had increased by three folds. On the other hand, the results obtained
by water infiltration under 40 kPa showed lower hydraulic
conductivities of 1.50×10-5 and 1.37×10-9 cm/s for 5% bentonite:
95% sand, and 10% bentonite: 90% sand, respectively. Similarly,
under 100 kPa, the hydraulic conductivities were 2.30×10-5 and
1.90×10-9 cm/s for 5% bentonite: 95% sand, and 10% bentonite: 90%
sand, respectively.
Abstract: Metrics is the process by which numbers or symbols
are assigned to attributes of entities in the real world in such a way as
to describe them according to clearly defined rules. Software metrics
are instruments or ways to measuring all the aspect of software
product. These metrics are used throughout a software project to
assist in estimation, quality control, productivity assessment, and
project control. Object oriented software metrics focus on
measurements that are applied to the class and other characteristics.
These measurements convey the software engineer to the behavior of
the software and how changes can be made that will reduce
complexity and improve the continuing capability of the software.
Object oriented software metric can be classified in two types static
and dynamic. Static metrics are concerned with all the aspects of
measuring by static analysis of software and dynamic metrics are
concerned with all the measuring aspect of the software at run time.
Major work done before, was focusing on static metric. Also some
work has been done in the field of dynamic nature of the software
measurements. But research in this area is demanding for more work.
In this paper we give a set of dynamic metrics specifically for
polymorphism in object oriented system.
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.
Abstract: The paper explores the development of an optimization of method and apparatus for retrieving extended high dynamic range from digital negative image. Architectural photo imaging can benefit from high dynamic range imaging (HDRI) technique for preserving and presenting sufficient luminance in the shadow and highlight clipping image areas. The HDRI technique that requires multiple exposure images as the source of HDRI rendering may not be effective in terms of time efficiency during the acquisition process and post-processing stage, considering it has numerous potential imaging variables and technical limitations during the multiple exposure process. This paper explores an experimental method and apparatus that aims to expand the dynamic range from digital negative image in HDRI environment. The method and apparatus explored is based on a single source of RAW image acquisition for the use of HDRI post-processing. It will cater the optimization in order to avoid and minimize the conventional HDRI photographic errors caused by different physical conditions during the photographing process and the misalignment of multiple exposed image sequences. The study observes the characteristics and capabilities of RAW image format as digital negative used for the retrieval of extended high dynamic range process in HDRI environment.
Abstract: This paper addresses the fundamental requirements for
starting an online business. It covers the process of ideation,
conceptualization, formulation, and implementation of new venture
ideas on the Web. Using Facebook as an illustrative example, we learn
how to turn an idea into a successful electronic business and to execute
a business plan with IT skills, management expertise, a good
entrepreneurial attitude, and an understanding of Internet culture. The
personality traits and characteristics of a successful e-commerce
entrepreneur are discussed with reference to Facebook-s founder,
Mark Zuckerberg. Facebook is a social and e-commerce success. It
provides a trusted environment of which participants can conduct
business with social experience. People are able to discuss products
before, during the after the sale within the Facebook environment. The
paper also highlights the challenges and opportunities for e-commerce
entrepreneurial startups to go public and of entering the China market.
Abstract: This article demonstrated development of
controlled release system of an NSAID drug, Diclofenac
sodium employing different ratios of Ethyl cellulose.
Diclofenac sodium and ethyl cellulose in different proportions
were processed by microencapsulation based on phase
separation technique to formulate microcapsules. The
prepared microcapsules were then compressed into tablets to
obtain controlled release oral formulations. In-vitro evaluation
was performed by dissolution test of each preparation was
conducted in 900 ml of phosphate buffer solution of pH 7.2
maintained at 37 ± 0.5 °C and stirred at 50 rpm. At predetermined
time intervals (0, 0.5, 1.0, 1.5, 2, 3, 4, 6, 8, 10, 12,
16, 20 and 24 hrs). The drug concentration in the collected
samples was determined by UV spectrophotometer at 276 nm.
The physical characteristics of diclofenac sodium
microcapsules were according to accepted range. These were
off-white, free flowing and spherical in shape. The release
profile of diclofenac sodium from microcapsules was found to
be directly proportional to the proportion of ethylcellulose and
coat thickness. The in-vitro release pattern showed that with
ratio of 1:1 and 1:2 (drug: polymer), the percentage release of
drug at first hour was 16.91 and 11.52 %, respectively as
compared to 1:3 which is only 6.87 % with in this time. The
release mechanism followed higuchi model for its release
pattern. Tablet Formulation (F2) of present study was found
comparable in release profile the marketed brand Phlogin-SR,
microcapsules showed an extended release beyond 24 h.
Further, a good correlation was found between drug release
and proportion of ethylcellulose in the microcapsules.
Microencapsulation based on coacervation found as good
technique to control release of diclofenac sodium for making
the controlled release formulations.
Abstract: The design of a landing gear is one of the fundamental aspects of aircraft design. The need for a light weight, high strength, and stiffness characteristics coupled with techno economic feasibility are a key to the acceptability of any landing gear construction. In this paper, an approach for analyzing two different designed landing gears for an unmanned aircraft vehicle (UAV) using advanced CAE techniques will be applied. Different landing conditions have been considered for both models. The maximum principle stresses for each model along with the factor of safety are calculated for every loading condition. A conclusion is drawing about better geometry.
Abstract: Here we have considered non uniform microstrip
leaky-wave antenna implemented on a dielectric waveguide by a
sinusoidal profile of periodic metallic grating. The non distribution of
the attenuation constant α along propagation axis, optimize the
radiating characteristics and performances of such antennas. The
method developped here is based on an integral method where the
formalism of the admittance operator is combined to a BKW
approximation. First, the effect of the modeling in the modal analysis
of complex waves is studied in detail. Then, the BKW model is used
for the dispersion analysis of the antenna of interest. According to
antenna theory, a forced continuity of the leaky-wave magnitude at
discontinuities of the non uniform structure is established. To test the
validity of our dispersion analysis, computed radiation patterns are
presented and compared in the millimeter band.
Abstract: This paper deals with modeling and parameter
identification of nonlinear systems described by Hammerstein model
having Piecewise nonlinear characteristics such as Dead-zone
nonlinearity characteristic. The simultaneous use of both an easy
decomposition technique and the triangular basis functions leads to a
particular form of Hammerstein model. The approximation by using
Triangular basis functions for the description of the static nonlinear
block conducts to a linear regressor model, so that least squares
techniques can be used for the parameter estimation. Singular Values
Decomposition (SVD) technique has been applied to separate the
coupled parameters. The proposed approach has been efficiently
tested on academic examples of simulation.