Abstract: Self-Excited Induction Generator (SEIG) builds up voltage while it enters in its magnetic saturation region. Due to non-linear magnetic characteristics, the performance analysis of SEIG involves cumbersome mathematical computations. The dependence of air-gap voltage on saturated magnetizing reactance can only be established at rated frequency by conducting a laboratory test commonly known as synchronous run test. But, there is no laboratory method to determine saturated magnetizing reactance and air-gap voltage of SEIG at varying speed, terminal capacitance and other loading conditions. For overall analysis of SEIG, prior information of magnetizing reactance, generated frequency and air-gap voltage is essentially required. Thus, analytical methods are the only alternative to determine these variables. Non-existence of direct mathematical relationship of these variables for different terminal conditions has forced the researchers to evolve new computational techniques. Artificial Neural Networks (ANNs) are very useful for solution of such complex problems, as they do not require any a priori information about the system. In this paper, an attempt is made to use cascaded neural networks to first determine the generated frequency and magnetizing reactance with varying terminal conditions and then air-gap voltage of SEIG. The results obtained from the ANN model are used to evaluate the overall performance of SEIG and are found to be in good agreement with experimental results. Hence, it is concluded that analysis of SEIG can be carried out effectively using ANNs.
Abstract: Endemic Artemia franciscana populations can be found throughout the American continent and also as an introduced specie in several country all over the world, such as in the Mediterranean region where Artemia franciscana was identified as an invasive specie replacing native Artemia parthenogenetica and Artemia salina. In the present study, the characterization of the new invasive Artemia franciscana reported from Sabkhet Halk El-Menzel (Tunisia) was done based on the cysts biometry, nauplii instar-I length, Adult sexual dimorphism and fatty acid profile. The mean value of the diameter of non-decapsulated and decapsulated cysts, chorion thickness and naupliar length is 235.8, 226.3, 4.75 and 426.8 μm, respectively. Sexual dimorphism for adults specimen showed that maximal distance between compound eyes, diameter for compound eyes, length of first antenna and the abdomen length compared to the total body length ratio, are the most important variables for males and females discrimination with a total contribution of 62.39 %. The analysis of fatty acid methyl esters profile of decapsulated cysts resulted in low levels of linolenic acid (LLA, C18:3n-3) and high levels of eicosapentaenoic acid (EPA, C20:5n-3) with 3.11 and 11.10 %, respectively. Low quantity of docosahexaenoic acid (DHA, 22:6n-3) was also observed with 0.17 mg.g-1 dry weight.
Abstract: Piezoelectric transformers are electronic devices made
from piezoelectric materials. The piezoelectric transformers as the
name implied are used for changing voltage signals from one level to another. Electrical energy carried with signals is transferred by means of mechanical vibration. Characterizing in both electrical and
mechanical properties leads to extensively use and efficiency enhancement of piezoelectric transformers in various applications. In
this paper, study and analysis of electrical and mechanical properties of multi-layer piezoelectric transformers in forms of potential and
displacement distribution throughout the volume, respectively. This
paper proposes a set of quasi-static mathematical model of electromechanical
coupling for piezoelectric transformer by using a set of
partial differential equations. Computer-based simulation utilizing the three-dimensional finite element method (3-D FEM) is exploited
as a tool for visualizing potentials and displacements distribution
within the multi-layer piezoelectric transformer. This simulation was
conducted by varying a number of layers. In this paper 3, 5 and 7 of
the circular ring type were used. The computer simulation based on
the use of the FEM has been developed in MATLAB programming environment.
Abstract: Polynomial bases and normal bases are both used for
elliptic curve cryptosystems, but field arithmetic operations such as
multiplication, inversion and doubling for each basis are implemented
by different methods. In general, it is said that normal bases, especially
optimal normal bases (ONB) which are special cases on normal bases,
are efficient for the implementation in hardware in comparison with
polynomial bases. However there seems to be more examined by
implementing and analyzing these systems under similar condition. In
this paper, we designed field arithmetic operators for each basis over
GF(2233), which field has a polynomial basis recommended by SEC2
and a type-II ONB both, and analyzed these implementation results.
And, in addition, we predicted the efficiency of two elliptic curve
cryptosystems using these field arithmetic operators.
Abstract: The main aim of this paper is to present the research
findings on the solution of centralized Web-Services for students by
adopting a framework and a prototype for Service Oriented
Architecture (SOA) Web-Services. The current situation of students-
Web-based application services has been identified and proposed an
effective SOA to increase the operational efficiency of Web-Services
for them it was necessary to identify the challenges in delivering a
SOA technology to increase operational efficiency of Web-Services.
Moreover, the SOA is an emerging concept, used for delivering
efficient student SOA Web-Services. Therefore, service reusability
from SOA Web-Services is provided and logically divided services
into smaller services to increase reusability and modularity. In this
case each service is a modular unit by itself and interoperability
services.
Abstract: The main objective of this paper is to determine the
isolated effect of silica fume on tensile, compressive and flexure strengths on high strength lightweight concrete. Many experiments
were carried out by replacing cement with different percentages of silica fume at different constant water-binder ratio keeping other mix
design variables constant. The silica fume was replaced by 0%, 5%,
10%, 15%, 20% and 25% for a water-binder ratios ranging from 0.26
to 0.42. For all mixes, split tensile, compressive and flexure strengths
were determined at 28 days. The results showed that the tensile, compressive and flexure strengths increased with silica fume incorporation but the optimum replacement percentage is not
constant because it depends on the water–cementitious material (w/cm) ratio of the mix. Based on the results, a relationship between
split tensile, compressive and flexure strengths of silica fume concrete was developed using statistical methods.
Abstract: The utilization of renewable energy sources in electric
power systems is increasing quickly because of public apprehensions
for unpleasant environmental impacts and increase in the energy
costs involved with the use of conventional energy sources. Despite
the application of these energy sources can considerably diminish the
system fuel costs, they can also have significant influence on the
system reliability. Therefore an appropriate combination of the
system reliability indices level and capital investment costs of system
is vital. This paper presents a hybrid wind/photovoltaic plant, with
the aim of supplying IEEE reliability test system load pattern while
the plant capital investment costs is minimized by applying a hybrid
particle swarm optimization (PSO) / harmony search (HS) approach,
and the system fulfills the appropriate level of reliability.
Abstract: Medical imaging uses the advantage of digital
technology in imaging and teleradiology. In teleradiology systems
large amount of data is acquired, stored and transmitted. A major
technology that may help to solve the problems associated with the
massive data storage and data transfer capacity is data compression
and decompression. There are many methods of image compression
available. They are classified as lossless and lossy compression
methods. In lossy compression method the decompressed image
contains some distortion. Fractal image compression (FIC) is a lossy
compression method. In fractal image compression an image is
coded as a set of contractive transformations in a complete metric
space. The set of contractive transformations is guaranteed to
produce an approximation to the original image. In this paper FIC is
achieved by PIFS using quadtree partitioning. PIFS is applied on
different images like , Ultrasound, CT Scan, Angiogram, X-ray,
Mammograms. In each modality approximately twenty images are
considered and the average values of compression ratio and PSNR
values are arrived. In this method of fractal encoding, the
parameter, tolerance factor Tmax, is varied from 1 to 10, keeping the
other standard parameters constant. For all modalities of images the
compression ratio and Peak Signal to Noise Ratio (PSNR) are
computed and studied. The quality of the decompressed image is
arrived by PSNR values. From the results it is observed that the
compression ratio increases with the tolerance factor and
mammogram has the highest compression ratio. The quality of the
image is not degraded upto an optimum value of tolerance factor,
Tmax, equal to 8, because of the properties of fractal compression.
Abstract: Drying characteristics of rough rice (variety of lenjan) with an initial moisture content of 25% dry basis (db) was studied in a hot air dryer assisted by infrared heating. Three arrival air temperatures (30, 40 and 500C) and four infrared radiation intensities (0, 0.2 , 0.4 and 0.6 W/cm2) and three arrival air speeds (0.1, 0.15 and 0.2 m.s-1) were studied. Bending strength of brown rice kernel, percentage of cracked kernels and time of drying were measured and evaluated. The results showed that increasing the drying arrival air temperature and radiation intensity of infrared resulted decrease in drying time. High bending strength and low percentage of cracked kernel was obtained when paddy was dried by hot air assisted infrared dryer. Between this factors and their interactive effect were a significant difference (p
Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: Apart from geometry, functionality is one of the most
significant hallmarks of a product. The functionality of a product can
be considered as the fundamental justification for a product
existence. Therefore a functional analysis including a complete and
reliable descriptor has a high potential to improve product
development process in various fields especially in knowledge-based
design. One of the important applications of the functional analysis
and indexing is in retrieval and design reuse concept. More than 75%
of design activity for a new product development contains reusing
earlier and existing design know-how. Thus, analysis and
categorization of product functions concluded by functional
indexing, influences directly in design optimization. This paper
elucidates and evaluates major classes for functional analysis by
discussing their major methods. Moreover it is finalized by
presenting a noble hybrid approach for functional analysis.
Abstract: A Watson-Crick automaton is recently introduced as a
computational model of DNA computing framework. It works on
tapes consisting of double stranded sequences of symbols. Symbols
placed on the corresponding cells of the double-stranded sequences are
related by a complimentary relation. In this paper, we investigate a
variation of Watson-Crick automata in which both heads read the tape
in reverse directions. They are called reverse Watson-Crick finite
automata (RWKFA). We show that all of following four classes, i.e.,
simple, 1-limited, all-final, all-final and simple, are equal to
non-restricted version of RWKFA.
Abstract: In this paper, we use nonlinear system identification method to predict and detect process fault of a cement rotary kiln. After selecting proper inputs and output, an input-output model is identified for the plant. To identify the various operation points in the
kiln, Locally Linear Neuro-Fuzzy (LLNF) model is used. This model is trained by LOLIMOT algorithm which is an incremental treestructure
algorithm. Then, by using this method, we obtained 3
distinct models for the normal and faulty situations in the kiln. One of the models is for normal condition of the kiln with 15 minutes
prediction horizon. The other two models are for the two faulty situations in the kiln with 7 minutes prediction horizon are presented.
At the end, we detect these faults in validation data. The data collected from White Saveh Cement Company is used for in this study.
Abstract: In this paper spatial variability of some chemical and
physical soil properties were investigated in mountain rangelands of
Nesho, Mazandaran province, Iran. 110 soil samples from 0-30 cm
depth were taken with systematic method on grid 30×30 m2 in
regions with different vegetation cover and transported to laboratory.
Then soil chemical and physical parameters including Acidity (pH),
Electrical conductivity, Caco3, Bulk density, Particle density, total
phosphorus, total Nitrogen, available potassium, Organic matter,
Saturation moisture, Soil texture (percentage of sand, silt and clay),
Sodium, Calcium, magnesium were measured in laboratory. Data
normalization was performed then was done statistical analysis for
description of soil properties and geostatistical analysis for indication
spatial correlation between these properties and were perpetrated
maps of spatial distribution of soil properties using Kriging method.
Results indicated that in the study area Saturation moisture and
percentage of Sand had highest and lowest spatial correlation
respectively.
Abstract: Natural frequencies and dynamic response of a spur
gear sector are investigated using a two dimensional finite element
model that offers significant advantages for dynamic gear analyses.
The gear teeth are analyzed for different operating speeds. A primary
feature of this modeling is determination of mesh forces using a
detailed contact analysis for each time step as the gears roll through
the mesh. Transient mode super position method has been used to
find horizontal and vertical components of displacement and
dynamic stress. The finite element analysis software ANSYS has
been used on the proposed model to find the natural frequencies by
Block Lanczos technique and displacements and dynamic stresses by
transient mode super position method. A comparison of theoretical
(natural frequency and static stress) results with the finite element
analysis results has also been done. The effect of rotational speed of
the gears on the dynamic response of gear tooth has been studied and
design limits have been discussed.
Abstract: A numerical study on the heat transfer in the thermal
barrier coatings and the substrates of a parallel-plate enclosure is
carried out. Some of the thermal barrier coatings, such as ceramics, are
semitransparent and are of interest for high-temperature applications
where radiation effects are significant. The radiative transfer equations
and the energy equations are solved by using the discrete ordinates
method and the finite difference method. Illustrative results are
presented for temperature distributions in the coatings and the opaque
walls under various heating conditions. The results show that the
temperature distribution is more uniform in the interior portion of each
coating away from its boundary for the case with a larger average of
varying refractive index and a positive gradient of refractive index
enhances radiative transfer to the substrates.
Abstract: This paper presents the study of a variable speed wind
energy conversion system based on a Doubly Fed Induction Generator
(DFIG) based on a sliding mode control applied to achieve control of
active and reactive powers exchanged between the stator of the DFIG
and the grid to ensure a Maximum Power Point Tracking (MPPT) of
a wind energy conversion system. The proposed control algorithm is
applied to a DFIG whose stator is directly connected to the grid and
the rotor is connected to the PWM converter. To extract a maximum
of power, the rotor side converter is controlled by using a stator
flux-oriented strategy. The created decoupling control between active
and reactive stator power allows keeping the power factor close to
unity. Simulation results show that the wind turbine can operate at
its optimum energy for a wide range of wind speed.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: When consistently innovative business-models can
give companies a competitive advantage, longitudinal empirical
research, which can reflect dynamic business-model changes, has yet
to prove a definitive connection. This study consequently employs a
dynamic perspective in conjunction with innovation theory to examine
the relationship between the types of business-model innovation and
firm value. This study tries to examine various types of
business-model innovation in high-end and low-end technology
industries such as HTC and the 7-Eleven chain stores with research
periods of 14 years and 32 years, respectively. The empirical results
suggest that adopting radical business-model innovation in addition to
expanding new target markets can successfully lead to a competitive
advantage. Sustained advanced technological competences and
service/product innovation are the key successful factors in high-end
and low-end technology industry business-models respectively. In
sum up, the business-model innovation can yield a higher market value
and financial value in high-end technology industries than low-end
ones.
Abstract: Organizational innovation favors technological
innovation, but does it also influence technological innovation
persistence? This article investigates empirically the pattern of
technological innovation persistence and tests the potential impact of
organizational innovation using firm-level data from three waves of
the French Community Innovation Surveys. Evidence shows a
positive effect of organizational innovation on technological
innovation persistence, according to various measures of
organizational innovation. Moreover, this impact is more significant
for complex innovators (i.e., those who innovate in both products and
processes). These results highlight the complexity of managing
organizational practices with regard to the firm-s technological
innovation. They also add to comprehension of the drivers of
innovation persistence, through a focus on an often forgotten
dimension of innovation in a broader sense.