Abstract: It is estimated that the total cost of abnormal
conditions to US process industries is around $20 billion dollars in
annual losses. The hydrotreatment (HDT) of diesel fuel in petroleum
refineries is a conversion process that leads to high profitable
economical returns. However, this is a difficult process to control
because it is operated continuously, with high hydrogen pressures
and it is also subject to disturbances in feed properties and catalyst
performance. So, the automatic detection of fault and diagnosis plays
an important role in this context. In this work, a hybrid approach
based on neural networks together with a pos-processing
classification algorithm is used to detect faults in a simulated HDT
unit. Nine classes (8 faults and the normal operation) were correctly
classified using the proposed approach in a maximum time of 5
minutes, based on on-line data process measurements.
Abstract: In this paper, a new reversible watermarking method is presented that reduces the size of a stereoscopic image sequence while keeping its content visible. The proposed technique embeds the residuals of the right frames to the corresponding frames of the left sequence, halving the total capacity. The residual frames may result in after a disparity compensated procedure between the two video streams or by a joint motion and disparity compensation. The residuals are usually lossy compressed before embedding because of the limited embedding capacity of the left frames. The watermarked frames are visible at a high quality and at any instant the stereoscopic video may be recovered by an inverse process. In fact, the left frames may be exactly recovered whereas the right ones are slightly distorted as the residuals are not embedded intact. The employed embedding method reorders the left frame into an array of consecutive pixel pairs and embeds a number of bits according to their intensity difference. In this way, it hides a number of bits in intensity smooth areas and most of the data in textured areas where resulting distortions are less visible. The experimental evaluation demonstrates that the proposed scheme is quite effective.
Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The efficient operation of any biological treatment
process requires pre-treatment of incompatible pollutants such as
acids, bases, oil, toxic substances, etc. which hamper the treatment
of other major components which are otherwise degradable. The
pre-treatment of alkaline waste-waters, generated from various
industries like textile, paper & pulp, potato-processing industries,
etc., having a pH of 10 or higher, is essential. The pre-treatment,
i.e., neutralization of such alkaline waste-waters can be achieved by
chemical as well as biological means. However, the biological pretreatment
offers better package over the chemical means by being
safe and economical. The biological pre-treatment can be
accomplished by using a blend of microorganisms able to withstand
such harsh alkaline conditions. In the present study, for the proper
pre-treatment of alkaline waste-waters, a package of alkalophilic
bacteria is formulated to neutralise the alkaline pH of the industrial
waste-waters. The developed microbial package is cost-effective as
well as environmental friendly.
Abstract: Existing underground pipe jacking methods use a
reinforcing rod in a steel tube to obtain structural stiffness. However,
some problems such as inconvenience of works and expensive
materials resulted from limited working space and reinforcing works
are existed. To resolve these problems, a new pipe jacking method,
namely PST (Prestressed Segment Tunnel) method, was developed
which used joint to connect the steel segment and form erection
structure. For evaluating the flexural capacity of the PST method
structure, a experimental test was conducted. The parameters
considered in the test were span-to-depth ratio of segment, diameter of
steel tube at the corner, prestressing force, and welding of joint. The
flexural behaviours with the effect of load capacity in serviceability
state according to different parameters were examined.. The frame
with long segments could increase flexural stiffness and the specimen
with large diameter of concave corner showed excellent resistance
ability to the negative moment. In addition, welding of joints increased
the flexural capacity.
Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,
Abstract: This paper presents a tested research concept that
implements a complex evolutionary algorithm, genetic algorithm
(GA), in a multi-microcontroller environment. Parallel Distributed
Genetic Algorithm (PDGA) is employed in adaptive beam forming
technique to reduce power usage of adaptive antenna at WCDMA
base station. Adaptive antenna has dynamic beam that requires more
advanced beam forming algorithm such as genetic algorithm which
requires heavy computation and memory space. Microcontrollers are
low resource platforms that are normally not associated with GAs,
which are typically resource intensive. The aim of this project was to
design a cooperative multiprocessor system by expanding the role of
small scale PIC microcontrollers to optimize WCDMA base station
transmitter power. Implementation results have shown that PDGA
multi-microcontroller system returned optimal transmitted power
compared to conventional GA.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: A preconditioned Jacobi (PJ) method is provided for solving fuzzy linear systems whose coefficient matrices are crisp Mmatrices and the right-hand side columns are arbitrary fuzzy number vectors. The iterative algorithm is given for the preconditioned Jacobi method. The convergence is analyzed with convergence theorems. Numerical examples are given to illustrate the procedure and show the effectiveness and efficiency of the method.
Abstract: This paper presented the results of an experimental
investigation into the axial fatigue behavior of a 5086 aluminum
alloy which have several notch-aspect ratios a0/c0 and notch
thickness ratio a/t with semi-elliptical surface cracks. Tests were
conducted in la b air for stress levels of 50 % of their yield
strength. Experiments were carried out for various notch to
thickness ratios. Crack growth rates of test specimens both in
surface and depth directions were determined by using die
penetration method. Fuzzy Logic method was used to predict the
deep direction crack growth because the dept of the crack is
considerably difficult to measure.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: Multilevel inverters supplied from equal and constant
dc sources almost don-t exist in practical applications. The variation
of the dc sources affects the values of the switching angles required
for each specific harmonic profile, as well as increases the difficulty
of the harmonic elimination-s equations. This paper presents an
extremely fast optimal solution of harmonic elimination of multilevel
inverters with non-equal dc sources using Tanaka's fuzzy linear
regression formulation. A set of mathematical equations describing
the general output waveform of the multilevel inverter with nonequal
dc sources is formulated. Fuzzy linear regression is then
employed to compute the optimal solution set of switching angles.
Abstract: In this paper, numerical simulation is used to
investigate the thermal performance of liquid cooling heatsink with
microchannels due to geometric arrangement. Commercial software
ICEPAK is utilized for the analysis. The considered parameters
include aspect ratio, porosity and the length and height of
microchannel. The aspect ratio varies from 3 to 16 and the length of
microchannel is 10mm, 14mm, and 18mm. The height of
microchannel is 2mm, 3mm and 4mm. It is found short channel have
better thermal efficiency than long channel at 490Pa. No matter the
length of channel the best aspect ratio is 4. It is also noted that pressure
difference at 2940Pa the best aspect ratio from 4 to 8, it means pressure
difference affect aspect ratio, effective thermal resistance at low
pressure difference but lower effective thermal resistance at high
pressure difference.
Abstract: Turbulence modeling of large-scale flow over a vegetated surface is complex. Such problems involve large scale computational domains, while the characteristics of flow near the surface are also involved. In modeling large scale flow, surface roughness including vegetation is generally taken into account by mean of roughness parameters in the modified law of the wall. However, the turbulence structure within the canopy region cannot be captured with this method, another method which applies source/sink terms to model plant drag can be used. These models have been developed and tested intensively but with a simple surface geometry. This paper aims to compare the use of roughness parameter, and additional source/sink terms in modeling the effect of plant drag on wind flow over a complex vegetated surface. The RNG k-ε turbulence model with the non-equilibrium wall function was tested with both cases. In addition, the k-ω turbulence model, which is claimed to be computationally stable, was also investigated with the source/sink terms. All numerical results were compared to the experimental results obtained at the study site Mason Bay, Stewart Island, New Zealand. In the near-surface region, it is found that the results obtained by using the source/sink term are more accurate than those using roughness parameters. The k-ω turbulence model with source/sink term is more appropriate as it is more accurate and more computationally stable than the RNG k-ε turbulence model. At higher region, there is no significant difference amongst the results obtained from all simulations.
Abstract: To estimate the risks of dam failure phenomenon, it is necessary to understand this phenomenon and the involved governing factors. Overtopping and piping are the two main reasons of earthdam failures. In the piping context, the piping is determined as a phenomenon which is occurred between two phases, the water liquid and the solid soil. In this investigation, the onset of piping and its development, as well as the movement of water in soil, are numerically approached. In this regard, a one-dimensional numerical model based on the mass-conserving finite-volume method is developed and applied in order to simulate the piping phenomenon in a continuous circular tunnel of given initial length and radius, located between upstream and downstream. The simulation result includes the time-variations of radius along the tunnel until the radius value reaches its critical and the piping phenomenon converts to overtopping.
Abstract: Recently, majors of doctors are divided into terribly lots of detailed areas. However, it is actually not a rare case that a doctor has a patient who is not in his/her major. He/She must judge an assessment and make a medical treatment plan for this patient. According to our investigation, conventional approaches such as image diagnosis cooperation are insufficient. This paper proposes an 'Assessment / Medical Treatment Plan Consulting System'. We have implemented a pilot system based on our proposition. Its effectiveness is clarified by an evaluation.
Abstract: This paper is a simple and systematic approaches to the design and analysis a pulse width modulation (PWM) based sliding mode controller for buck DC-DC Converters. Various aspects of the design, including the practical problems and the proposed solutions, are detailed. However, these control strategies can't compensate for large load current and input voltage variations. In this paper, a new control strategy by compromising both schemes advantages and avoiding their drawbacks is proposed, analyzed and simulated.
Abstract: This study is aimed to investigate feasibility of the
aerobic biological process to treat oily wastewater from palm oil food
industry. Effect of aeration and sludge concentrations are studied.
Raw sludge and raw wastewater was mixed and acclimatized for five
days in a stirred tank reactor. The aeration rate (no aeration, low;
1.5L/min and high rate; 2L/min) and sludge concentration (3675,
7350, and 11025mg/L of VSS) were varied. Responses of process
were pH, COD, oil and grease, VSS, and PHB content. It was found
that the treatment can remove 85.1 to 97.1 % of COD and remove
12.9 to 54.8% of oil & grease. The PHB yield was found to be within
0.15% to 2.4% as PHB/VSS ratio and 0.01% to 0.12% as PHB/COD
removed. The higher aeration results a high COD removal and oil &
grease removal, while experiment without aeration gives better PHB
yield. Higher sludge concentrations (11025mg/L VSS) give higher
removal of oil & grease while moderate sludge concentration
(7350mg/L VSS) give better result in COD removal. Higher PHB
yield is obtained in low sludge concentration (3675mg/L).
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: In recent years, copulas have become very popular in
financial research and actuarial science as they are more flexible in
modelling the co-movements and relationships of risk factors as compared
to the conventional linear correlation coefficient by Pearson.
However, a precise estimation of the copula parameters is vital in
order to correctly capture the (possibly nonlinear) dependence structure
and joint tail events. In this study, we employ two optimization
heuristics, namely Differential Evolution and Threshold Accepting to
tackle the parameter estimation of multivariate t distribution models
in the EML approach. Since the evolutionary optimizer does not rely
on gradient search, the EML approach can be applied to estimation of
more complicated copula models such as high-dimensional copulas.
Our experimental study shows that the proposed method provides
more robust and more accurate estimates as compared to the IFM
approach.