Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: Aiming at the problems existing in low-carbon technology of Chinese manufacturing industries, such as irrational energy structure, lack of technological innovation, financial constraints, this paper puts forward the suggestion that the leading role of the government is combined with the roles of enterprises and market. That is, through increasing the governmental funding the adjustment of the industrial structures and enhancement of the legal supervision are supported. Technological innovation is accelerated by the enterprises, and the carbon trading will be promoted so as to trigger the low-carbon revolution in Chinese manufacturing field.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: CIM is the standard formalism for modeling management
information developed by the Distributed Management Task
Force (DMTF) in the context of its WBEM proposal, designed to
provide a conceptual view of the managed environment. In this
paper, we propose the inclusion of formal knowledge representation
techniques, based on Description Logics (DLs) and the Web Ontology
Language (OWL), in CIM-based conceptual modeling, and then we
examine the benefits of such a decision. The proposal is specified
as a CIM metamodel level mapping to a highly expressive subset
of DLs capable of capturing all the semantics of the models. The
paper shows how the proposed mapping provides CIM diagrams with
precise semantics and can be used for automatic reasoning about the
management information models, as a design aid, by means of newgeneration
CASE tools, thanks to the use of state-of-the-art automatic
reasoning systems that support the proposed logic and use algorithms
that are sound and complete with respect to the semantics. Such a
CASE tool framework has been developed by the authors and its
architecture is also introduced. The proposed formalization is not
only useful at design time, but also at run time through the use of
rational autonomous agents, in response to a need recently recognized
by the DMTF.
Abstract: The development of many measurement and inspection systems of products based on real-time image processing can not be carried out totally in a laboratory due to the size or the temperature of the manufactured products. Those systems must be developed in successive phases. Firstly, the system is installed in the production line with only an operational service to acquire images of the products and other complementary signals. Next, a recording service of the image and signals must be developed and integrated in the system. Only after a large set of images of products is available, the development of the real-time image processing algorithms for measurement or inspection of the products can be accomplished under realistic conditions. Finally, the recording service is turned off or eliminated and the system operates only with the real-time services for the acquisition and processing of the images. This article presents a systematic performance evaluation of the image compression algorithms currently available to implement a real-time recording service. The results allow establishing a trade off between the reduction or compression of the image size and the CPU time required to get that compression level.
Abstract: This work presents the mixed-mode II/III prestressed split-cantilever beam specimen for the fracture testing of composite materials. In accordance with the concept of prestressed composite beams one of the two fracture modes is provided by the prestressed state of the specimen, and the other one is increased up to fracture initiation by using a testing machine. The novel beam-like specimen is able to provide any combination of the mode-II and mode-III energy release rates. A simple closed-form solution is developed using beam theory as a data reduction scheme and for the calculation of the energy release rates in the new configuration. The applicability and the limitations of the novel fracture mechanical test are demonstrated using unidirectional glass/polyester composite specimens. If only crack propagation onset is involved then the mixed-mode beam specimen can be used to obtain the fracture criterion of transparent composite materials in the GII - GIII plane in a relatively simple way.
Abstract: The study applied a combination of organisational learning models (Senge, 1994: Pedler, Burgoyne and Boydell, 1991) and later adopted fifteen organisational learning principles with one of the biggest energy providers in South East Asia. The purposes of the current study were to: a) investigate the company-s practices on fifteen organisational learning principles; b) explore the perceptions and expectations of its employees in relations to the principles; and c) compare the perceptions and expectations between management and non-management staff toward the fifteen factors. One hundred and ten employees responded on a designed questionnaire and the results indicated that the company was practicing activities that associated with organisational learning principles. Also, according to the T-test results, significant differences between management and non-management respondents were found. Research implications are also provided.
Abstract: Employees commitments of vision and mission of
organization is effected due to manager’s executes by approach of
leadership The leaders who have attributions like vision, confidence
and correctitude, sharing and participation, creativeness, progressive
learning –improvement and responsibility are effective to increase
organizational commitment if they are sensitive to expectation and
requirement of employees in an organization. Studies about
organizational commitment appear results that employees who have
strong organizational commitment have the most contribution. In this
study, “Leadership” and “Organizational Commitment” conduct
surveys to 31 employees of Ahmet Özdemir Nak. Tic. San. A.Ş.
which has operations in road and railway transportation sector. It is
analyzed the effects of leadership approach to organizational
commitment deals with result of survey.
Abstract: Road Traffic Accidents are a major cause of disability and death throughout the world. The control of intelligent vehicles in order to reduce human error and boost ease congestion is not accomplished solely by the aid of human resources. The present article is an attempt to introduce an intelligent control system based on RFID technology. By the help of RFID technology, vehicles are connected to computerized systems, intelligent light poles and other available hardware along the way. In this project, intelligent control system is capable of tracking all vehicles, crisis management and control, traffic guidance and recording Driving offences along the highway.
Abstract: Capacitive electrocardiogram (ECG) measurement is an attractive approach for long-term health monitoring. However, there is little literature available on its implementation, especially for multichannel system in standard ECG leads. This paper begins from the design criteria for capacitive ECG measurement and presents a multichannel limb-lead capacitive ECG system with conductive fabric tapes pasted on a double layer PCB as the capacitive sensors. The proposed prototype system incorporates a capacitive driven-body (CDB) circuit to reduce the common-mode power-line interference (PLI). The presented prototype system has been verified to be stable by theoretic analysis and practical long-term experiments. The signal quality is competitive to that acquired by commercial ECG machines. The feasible size and distance of capacitive sensor have also been evaluated by a series of tests. From the test results, it is suggested to be greater than 60 cm2 in sensor size and be smaller than 1.5 mm in distance for capacitive ECG measurement.
Abstract: Direction of Arrival estimation refers to defining a mathematical function called a pseudospectrum that gives an indication of the angle a signal is impinging on the antenna array. This estimation is an efficient method of improving the quality of service in a communication system by focusing the reception and transmission only in the estimated direction thereby increasing fidelity with a provision to suppress interferers. This improvement is largely dependent on the performance of the algorithm employed in the estimation. Many DOA algorithms exists amongst which are MUSIC, Root-MUSIC and ESPRIT. In this paper, performance of these three algorithms is analyzed in terms of complexity, accuracy as assessed and characterized by the CRLB and memory requirements in various environments and array sizes. It is found that the three algorithms are high resolution and dependent on the operating environment and the array size.
Abstract: The three steps of the standard one-way nested grid
for a regional scale of the third generation WAve Model Cycle 4
(WAMC4) is scrutinized. The model application is enabled to solve
the energy balance equation on a coarse resolution grid in order to
produce boundary conditions for a smaller area by the nested grid
technique. In the present study, the model takes a full advantage of the
fine resolution of wind fields in space and time produced by the available
U.S. Navy Global Atmospheric Prediction System (NOGAPS)
model with 1 degree resolution. The nested grid application of the
model is developed in order to gradually increase the resolution from
the open ocean towards the South China Sea (SCS) and the Gulf of
Thailand (GoT) respectively. The model results were compared with
buoy observations at Ko Chang, Rayong and Huahin locations which
were obtained from the Seawatch project. In addition, the results were
also compared with Satun based weather station which was provided
from Department of Meteorology, Thailand. The data collected from
this station presented the significant wave height (Hs) reached 12.85
m. The results indicated that the tendency of the Hs from the model
in the spherical coordinate propagation with deep water condition in
the fine grid domain agreed well with the Hs from the observations.
Abstract: Five lignin samples were fractionated with
Acetone/Water mixtures and the obtained fractions were subjected to
extensive structural characterization, including Fourier Transform
Infrared (FT-IR), Gel permeation Chromatography (GPC) and
Phosphorus-31 NMR spectroscopy (31P-NMR). The results showed
that for all studied lignins the solubility increases with the increment
of the acetone concentration. Wheat straw lignin has the highest
solubility in 90/10 (v/v) Acetone/Water mixture, 400 mg lignin being
dissolved in 1 mL mixture. The weight average molecular weight of
the obtained fractions increased with the increment of acetone
concentration and thus with solubility. 31P-NMR analysis based on
lignin modification by reactive phospholane into phosphitylated
compounds was used to differentiate and quantify the different types
of OH groups (aromatic, aliphatic, and carboxylic) found in the
fractions obtained with 70/30 (v/v) Acetone/Water mixture.
Abstract: Qualification of doctoral students- and the candidates for a scientific degree is evaluated by the ability to solve scientific ideas in an innovative way, consequently, being a potential of research and science they play a significant role in the sustainability context of the society. The article deals with the analysis of the results of the pilot project, the aim of which has been to study the structure of doctoral students- research competences in the sustainability context. With the existance of variety of theories on research competence development, their analysis focuses on the attained aim approach. Three competence groups have been identified in this study: informative, communicative and instrumental. Within the study the doctoral students and candidates for a scientific degree (N=64) made their self-assessment of research competences. The study results depict their present research competence development level and its dynamics according to the aim to attain.
Abstract: Wireless sensor networks can be used to measure and monitor many challenging problems and typically involve in monitoring, tracking and controlling areas such as battlefield monitoring, object tracking, habitat monitoring and home sentry systems. However, wireless sensor networks pose unique security challenges including forgery of sensor data, eavesdropping, denial of service attacks, and the physical compromise of sensor nodes. Node in a sensor networks may be vanished due to power exhaustion or malicious attacks. To expand the life span of the sensor network, a new node deployment is needed. In military scenarios, intruder may directly organize malicious nodes or manipulate existing nodes to set up malicious new nodes through many kinds of attacks. To avoid malicious nodes from joining the sensor network, a security is required in the design of sensor network protocols. In this paper, we proposed a security framework to provide a complete security solution against the known attacks in wireless sensor networks. Our framework accomplishes node authentication for new nodes with recognition of a malicious node. When deployed as a framework, a high degree of security is reachable compared with the conventional sensor network security solutions. A proposed framework can protect against most of the notorious attacks in sensor networks, and attain better computation and communication performance. This is different from conventional authentication methods based on the node identity. It includes identity of nodes and the node security time stamp into the authentication procedure. Hence security protocols not only see the identity of each node but also distinguish between new nodes and old nodes.
Abstract: Although Model Driven Architecture has taken
successful steps toward model-based software development, this
approach still faces complex situations and ambiguous questions
while applying to real world software systems. One of these
questions - which has taken the most interest and focus - is how
model transforms between different abstraction levels, MDA
proposes. In this paper, we propose an approach based on Story
Driven Modeling and Aspect Oriented Programming to ease these
transformations. Service Oriented Architecture is taken as the target
model to test the proposed mechanism in a functional system.
Service Oriented Architecture and Model Driven Architecture [1]
are both considered as the frontiers of their own domain in the
software world. Following components - which was the greatest step
after object oriented - SOA is introduced, focusing on more
integrated and automated software solutions. On the other hand - and
from the designers' point of view - MDA is just initiating another
evolution. MDA is considered as the next big step after UML in
designing domain.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.