Abstract: Research and development R&D work involves
enormous amount of work that has to do with data measurement and
collection. This process evolves as new information is fed, new
technologies are utilized, and eventually new knowledge is created
by the stakeholders i.e., researchers, clients, and end-users. When
new knowledge is created, procedures of R&D work should evolve
and produce better results within improved research skills and
improved methods of data measurements and collection. This
measurement improvement should then be benchmarked against a
metric that should be developed at the organization. In this paper, we
are suggesting a conceptual metric for R&D work performance
improvement (PI) at the Kuwait Institute for Scientific Research
(KISR). This PI is to be measured against a set of variables in the
suggested metric, which are more closely correlated to organizational
output, as opposed to organizational norms. The paper also mentions
and discusses knowledge creation and management as an addedvalue
to R&D work and measurement improvement. The research
methodology followed in this work is qualitative in nature, based on
a survey that was distributed to researchers and interviews held with
senior researchers at KISR. Research and analyses in this paper also
include looking at and analyzing KISR-s literature.
Abstract: Banana is one of the most consumed fruits in the tropics and subtropics. Brazil accounts for about 9% of the world banana production. However, the production losses are as high as 30 to 40% and even much higher in some developing countries. The green banana flour is a complex carbohydrate source, including a high total starch (73.4%), resistant starch (17.5%) with functional properties. Gamma irradiation is considered to be an alternative method for food preservation. It has been performed due to the need of extending the shelf - life of foods, whilst maintaining their safety and avoiding one of the main concerns: the nutrient loss. In this work data about on the effects of ionizing radiation on the physicochemical analysis (carbohydrate, proteins, lipids, alimentary fiber, moistures and ashes) of Brazilian functional products (biscuits and bread) of the green banana pulp are presented. The caloric value was calculated. No significant difference was observed between the samples of irradiated and non – irradiated green banana biscuits with the following determinations: carbohydrates, proteins, alimentary fiber and ashes. Only a small significant difference was found in lipids (macronutrients). The results of physical chemical analysis of the irradiated and non- irradiated green banana bread non- irradiated showed no significant difference with the following determinations: carbohydrates, lipids (macronutrients), moisture, ashes and caloric value. A small difference was found in proteins (macronutrients). Irradiation of functional products (biscuits and bread) with doses of 1 and 3kGy maintained their original macronutrients content, showing good radioresistance.
Abstract: Producing IT products/services required carefully
designed. IT development process is intangible and labour intensive.
Making optimal use of available resources, both soft (knowledge,
skill-set etc.) and hard (computer system, ancillary equipment etc.),
is vital if IT development is to achieve sensible economical
advantages. Apart from the norm of Project Life Cycle and System
Development Life Cycle (SDLC), there is an urgent need to establish
a general yet widely acceptable guideline on the most effective and
efficient way to precede an IT project in the broader view of Product
Life Cycle. The current paper proposes such a framework with two
major areas of concern: (1) an integration of IT Products and IT
Services within an existing IT Process architecture and; (2) how IT
Product and IT Services are built into the framework of Product Life
Cycle, Project Life Cycle and SDLC.
Abstract: The main objective of this work is to provide a fault detection and isolation based on Markov parameters for residual generation and a neural network for fault classification. The diagnostic approach is accomplished in two steps: In step 1, the system is identified using a series of input / output variables through an identification algorithm. In step 2, the fault is diagnosed comparing the Markov parameters of faulty and non faulty systems. The Artificial Neural Network is trained using predetermined faulty conditions serves to classify the unknown fault. In step 1, the identification is done by first formulating a Hankel matrix out of Input/ output variables and then decomposing the matrix via singular value decomposition technique. For identifying the system online sliding window approach is adopted wherein an open slit slides over a subset of 'n' input/output variables. The faults are introduced at arbitrary instances and the identification is carried out in online. Fault residues are extracted making a comparison of the first five Markov parameters of faulty and non faulty systems. The proposed diagnostic approach is illustrated on benchmark problems with encouraging results.
Abstract: Investigation of sandy clay behavior is important since
urban development demands mean that sandy clay areas are
increasingly encountered, especially for transportation
infrastructures. This paper presents the results of the finite element
analysis of the direct shear test (under three vertical loading 44, 96
and 192 kPa) and discusses the effects of different parameters such as
cohesion, friction angle and Young's modulus on the shear strength of
sandy clay. The numerical model was calibrated against the
experimental results of large-scale direct shear tests. The results have
shown that the shear strength was increased with increase in friction
angle and cohesion. However, the shear strength was not influenced
by raising the friction angle at normal stress of 44 kPa. Also, the
effect of different young's modulus factors on stress-strain curve was
investigated.
Abstract: Numerical investigation of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann methods at different Reynolds numbers. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations, streamlines and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The Reynolds numbers affected the physical quantities.
Abstract: A sophisticated simulator provides a cost-effective measure to carry out preliminary mission testing and diagnostic while reducing potential failures for real life at sea trials. The presented simulation framework covers three key areas: AUV modeling, sensor modeling, and environment modeling. AUV modeling mainly covers the area of AUV dynamics. Sensor modeling deals with physics and mathematical models that govern each sensor installed onto the AUV. Environment model incorporates the hydrostatic, hydrodynamics, and ocean currents that will affect the AUV in a real-time mission. Based on this designed simulation framework, custom scenarios provided by the user can be modeled and its corresponding behaviors can be observed. This paper focuses on the accuracy of the simulated data from AUV model and environmental model derived from a developed AUV test-bed which was jointly upgraded by DSTO and the University of Adelaide. The main contribution of this paper is to experimentally verify the accuracy of the proposed simulation framework.
Abstract: This paper presents an new vision technique for
robotic manipulation of randomly oriented objects in industrial
applications. The proposed approach uses 2D and 3D vision for
efficiently extracting the 3D pose of an object in the presence of
multiple randomly positioned objects. 2D vision permits to quickly
select the objects of interest for 3D processing with a new modified
ICP algorithm (FaR-ICP), thus reducing significantly the processing
time. The extracted 3D pose is then sent to the robot manipulator for
picking. The tests show that the proposed system achieves high
performances
Abstract: Deciding the numerous parameters involved in
designing a competent artificial neural network is a complicated task.
The existence of several options for selecting an appropriate
architecture for neural network adds to this complexity, especially
when different applications of heterogeneous natures are concerned.
Two completely different applications in engineering and medical
science were selected in the present study including prediction of
workpiece's surface roughness in ultrasonic-vibration assisted turning
and papilloma viruses oncogenicity. Several neural network
architectures with different parameters were developed for each
application and the results were compared. It was illustrated in this
paper that some applications such as the first one mentioned above
are apt to be modeled by a single network with sufficient accuracy,
whereas others such as the second application can be best modeled
by different expert networks for different ranges of output.
Development of knowledge about the essentials of neural networks
for different applications is regarded as the cornerstone of
multidisciplinary network design programs to be developed as a
means of reducing inconsistencies and the burden of the user
intervention.
Abstract: Microstructure, wetting behavior and interfacial
reactions between Sn–0.7Cu and Sn–0.3Ag–0.7Cu (SAC0307)
solders solidified on Ni coated Al substrates were compared and
investigated. Microstructure of Sn–0.7Cu alloy exhibited a eutectic
matrix composed of primary β-Sn dendrites with a fine dispersion of
Cu6Sn5 intermetallics whereas microstructure of SAC0307 alloy
exhibited coarser Cu6Sn5 and finer Ag3Sn precipitates of IMCs with
decreased tin dendrites. Contact angles ranging from 22° to 26° were
obtained for Sn–0.7Cu solder solidified on substrate surface whereas
for SAC0307 solder alloy contact angles were found to be in the
range of 20° to 22°. Sn–0.7Cu solder/substrate interfacial region
exhibited faceted (Cu, Ni)6Sn5 IMCs protruding into the solder matrix
and a small amount of (Cu, Ni)3Sn4 intermetallics at the interface.
SAC0307 solder/substrate interfacial region showed mainly (Cu,
Ni)3Sn4 intermetallics adjacent to the coating layer and (Cu,
Ni)6Sn5 IMCs in the solder matrix. The improvement in the
wettability of SAC0307 solder alloy on substrate surface is attributed
to the formation of cylindrical shape (Cu,Ni)6Sn5 and a layer of
(Cu, Ni)3Sn4 IMCs at the interface.
Abstract: Two completely different approaches for a Gigabit
Ethernet compliant stream transmission over 50m of 1mm PMMA SI-POF have been experimentally demonstrated and are compared in this paper. The first solution is based on a commercial RC-LED
transmission and a careful optimization of the physical layer architecture, realized during the POF-PLUS EU Project. The second solution exploits the performance of an edge-emitting laser at the
transmitter side in order to avoid any sort of electrical equalization at the receiver side.
Abstract: A concept of switched beam antennas consisting of
2×2 rectangular array spaced by λ/4 accompanied with a null locating
has been proposed in the previous work. In this letter, the
performance evaluations of its prototype are presented. The benefits
of using proposed system have been clearly measured in term of
signal quality, throughput and delays. Also, the impact of position
shift which mesh router is not located on the expected beam direction
has also been investigated.
Abstract: Portuguese diet has been gradually diverging from the basic principles of healthy eating, leading to an unbalanced dietary pattern which, associated with increasing sedentary lifestyle, has a negative impact on public health. The main objective of this work was to characterize the dietary habits of university students in Viseu, Portugal. The study consisted of a sample of 80 university students, aged between 18 and 28 years. Anthropometric data (weight (kg) and height (m)) were collected and Body Mass Index (BMI) was calculated. The dietary habits were assessed through a three-day food record and the software Medpoint was used to convert food into energy and nutrients. The results showed that students present a normal body mass index. Female university students made a higher number of daily meals than male students, and these last skipped breakfast more frequently. The values of average daily intake of energy, macronutrients and calcium were higher in males. The food pattern was characterized by a predominant consumption of meat, cereal, fats and sugar. Dietary intake of dairy products, fruits, vegetables and legumes does not meet the recommendations, revealing inadequate food habits such as hypoglycemic, hyperprotein and hyperlipidemic diet. Our findings suggest that preventive interventions should be focus in promoting healthy eating habits and physical activity in adulthood.
Abstract: Processing the data by computers and performing
reasoning tasks is an important aim in Computer Science. Semantic
Web is one step towards it. The use of ontologies to enhance the
information by semantically is the current trend. Huge amount of
domain specific, unstructured on-line data needs to be expressed in
machine understandable and semantically searchable format.
Currently users are often forced to search manually in the results
returned by the keyword-based search services. They also want to use
their native languages to express what they search. In this paper, an
ontology-based automated question answering system on software
test documents domain is presented. The system allows users to enter
a question about the domain by means of natural language and
returns exact answer of the questions. Conversion of the natural
language question into the ontology based query is the challenging
part of the system. To be able to achieve this, a new algorithm
regarding free text to ontology based search engine query conversion
is proposed. The algorithm is based on investigation of suitable
question type and parsing the words of the question sentence.
Abstract: Low frequency power oscillations may be triggered
by many events in the system. Most oscillations are damped by the
system, but undamped oscillations can lead to system collapse.
Oscillations develop as a result of rotor acceleration/deceleration
following a change in active power transfer from a generator. Like
the operations limits, the monitoring of power system oscillating
modes is a relevant aspect of power system operation and control.
Unprevented low-frequency power swings can be cause of cascading
outages that can rapidly extend effect on wide region. On this regard,
a Wide Area Monitoring, Protection and Control Systems
(WAMPCS) help in detecting such phenomena and assess power
system dynamics security. The monitoring of power system
electromechanical oscillations is very important in the frame of
modern power system management and control. In first part, this
paper compares the different technique for identification of power
system oscillations. Second part analyzes possible identification
some power system dynamics behaviors Using Wide Area
Monitoring Systems (WAMS) based on Phasor Measurement Units
(PMUs) and wavelet technique.
Abstract: Effect of temperature and light was investigated on a
thin film of organic semiconductor formyl-TIPPCu(II) deposited on a
glass substrate with preliminary evaporated gold electrodes. The
electrical capacitance and resistance of the fabricated device were
evaluated under the effect of temperature and light. The relative
capacitance of the fabricated sensor increased by 4.3 times by rising
temperature from 27 to 1870C, while under illumination up to 25000
lx, the capacitance of the Au/formyl-TIPPCu(II)/Au photo capacitive
sensor increased continuously by 13.2 times as compared to dark
conditions.
Abstract: Measurements of radioactivity in the environment is of great importance to monitor and control the levels of radiation to which man is exposed directly or indirectly. It is necessary to show that regardless of working or being close to nuclear power plants, people are daily in contact with some amount of radiation from the actual environment and food that are ingested, contradicting the view of most of them. The aim of this study was to analyze the rate of natural and artificial radiation from radionuclides present in cement, soil and fertilizers used in Sergipe State – Brazil. The radionuclide activitiesmeasured all samples arebelow the Brazilian limit of the exclusion and exemption criteria from the requirement of radiation protection.It was detected Be-7 in organic fertilizers that means a short interval between the brewing processes for use in agriculture. It was also detected an unexpected Cs-137 in some samples; however its activities does not represent risk for the population. Th-231 was also found in samples of soil and cement in the state of Sergipe that is an unprecedented result.
Abstract: This paper describes a novel optimized JTAG interface circuit between a JTAG controller and target IC. Being able to access JTAG using only one or two pins, this circuit does not change the original boundary scanning test frequency of target IC. Compared with the traditional JTAG interface which based on IEEE std. 1149.1, this reduced pin technology is more applicability in pin limited devices, and it is easier to control the scale of target IC for the designer.
Abstract: A multi fingered dexterous anthropomorphic hand is
being developed by the authors. The focus of the hand is the
replacement of human operators in hazardous environments and also
in environments where zero tolerance is observed for the human
errors. The robotic hand will comprise of five fingers (four fingers
and one thumb) each having four degrees of freedom (DOF) which
can perform flexion, extension, abduction, adduction and also
circumduction. For the actuation purpose pneumatic muscles and
springs will be used. The paper exemplifies the mechanical design for
the robotic hand. It also describes different mechanical designs that
have been developed before date.
Abstract: In this work, we present a novel active learning approach
for learning a visual object detection system. Our system
is composed of an active learning mechanism as wrapper around
a sub-algorithm which implement an online boosting-based learning
object detector. In the core is a combination of a bootstrap procedure
and a semi automatic learning process based on the online boosting
procedure. The idea is to exploit the availability of classifier during
learning to automatically label training samples and increasingly
improves the classifier. This addresses the issue of reducing labeling
effort meanwhile obtain better performance. In addition, we propose
a verification process for further improvement of the classifier.
The idea is to allow re-update on seen data during learning for
stabilizing the detector. The main contribution of this empirical study
is a demonstration that active learning based on an online boosting
approach trained in this manner can achieve results comparable or
even outperform a framework trained in conventional manner using
much more labeling effort. Empirical experiments on challenging data
set for specific object deteciton problems show the effectiveness of
our approach.