Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.
Abstract: In the process of polyethylene extrusion polymer
material similar to powder or granule is under compression, melting
and transmission operation and on base of special form, extrudate has
been produced. Twin-screw extruders are applicable in industries
because of their high capacity. The powder mixing with chemical
additives and melting with thermal and mechanical energy in three
zones (feed, compression and metering zone) and because of gear
pump and screw's pressure, converting to final product in latest plate.
Extruders with twin-screw and short distance between screws are
better than other types because of their high capacity and good
thermal and mechanical stress.
In this paper, process of polyethylene extrusion and various tapes
of extruders are studied. It is necessary to have an exact control on
process to producing high quality products with safe operation and
optimum energy consumption.
The granule size is depending on granulator motor speed. Results
show at constant feed rate a decrease in granule size was found whit
Increase in motor speed. Relationships between HDPE feed rate and
speed of granulator motor, main motor and gear pump are calculated
following as:
x = HDPE feed flow rate, yM = Main motor speed
yM = (-3.6076e-3) x^4+ (0.24597) x^3+ (-5.49003) x^2+ (64.22092)
x+61.66786 (1)
x = HDPE feed flow rate, yG = Gear pump speed
yG = (-2.4996e-3) x^4+ (0.18018) x^3+ (-4.22794) x^2+ (48.45536)
x+18.78880 (2)
x = HDPE feed flow rate, y = Granulator motor speed
10th Degree Polynomial Fit: y = a+bx+cx^2+dx^3... (3)
a = 1.2751, b = 282.4655, c = -165.2098,
d = 48.3106, e = -8.18715, f = 0.84997
g = -0.056094, h = 0.002358, i = -6.11816e-5
j = 8.919726e-7, k = -5.59050e-9
Abstract: In the present work, we propose a new method for
solving the matrix equation AXB=F . The new method can
be considered as a generalized form of the well-known global full
orthogonalization method (Gl-FOM) for solving multiple linear
systems. Hence, the method will be called extended Gl-FOM (EGl-
FOM). For implementing EGl-FOM, generalized forms of block
Krylov subspace and global Arnoldi process are presented. Finally,
some numerical experiments are given to illustrate the efficiency of
our new method.
Abstract: A modified Genetic Algorithm (GA) based optimal selection of parameters for Automatic Generation Control (AGC) of multi-area electric energy systems is proposed in this paper. Simulations on multi-area reheat thermal system with and without consideration of nonlinearity like governor dead band followed by 1% step load perturbation is performed to exemplify the optimum parameter search. In this proposed method, a modified Genetic Algorithm is proposed where one point crossover with modification is employed. Positional dependency in respect of crossing site helps to maintain diversity of search point as well as exploitation of already known optimum value. This makes a trade-off between exploration and exploitation of search space to find global optimum in less number of generations. The proposed GA along with decomposition technique as developed has been used to obtain the optimum megawatt frequency control of multi-area electric energy systems. Time-domain simulations are conducted with trapezoidal integration along with decomposition technique. The superiority of the proposed method over existing one is verified from simulations and comparisons.
Abstract: The Minimum Weighted Vertex Cover (MWVC) problem is a classic graph optimization NP - complete problem. Given an undirected graph G = (V, E) and weighting function defined on the vertex set, the minimum weighted vertex cover problem is to find a vertex set S V whose total weight is minimum subject to every edge of G has at least one end point in S. In this paper an effective algorithm, called Support Ratio Algorithm (SRA), is designed to find the minimum weighted vertex cover of a graph. Computational experiments are designed and conducted to study the performance of our proposed algorithm. Extensive simulation results show that the SRA can yield better solutions than other existing algorithms found in the literature for solving the minimum vertex cover problem.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: In today-s modern world, the number of vehicles is
increasing on the road. This causes more people to choose walking
instead of traveling using vehicles. Thus, proper planning of
pedestrians- paths is important to ensure the safety of pedestrians in a
walking area. Crowd dynamics study the pedestrians- behavior and
modeling pedestrians- movement to ensure safety in their walking paths.
To date, many models have been designed to ease pedestrians-
movement. The Social Force Model is widely used among researchers
as it is simpler and provides better simulation results. We will discuss
the problem regarding the ritual of circumambulating the Ka-aba
(Tawaf) where the entrances to this area are usually congested which
worsens during the Hajj season. We will use the computer simulation
model SimWalk which is based on the Social Force Model to simulate
the movement of pilgrims in the Tawaf area. We will first discuss the
effect of uni and bi-directional flows at the gates. We will then restrict
certain gates to the area as the entrances only and others as exits only.
From the simulations, we will study the effect of the distance of other
entrances from the beginning line and their effects on the duration of
pilgrims circumambulate Ka-aba. We will distribute the pilgrims at the
different entrances evenly so that the congestion at the entrances can be
reduced. We would also discuss the various locations and designs of
barriers at the exits and its effect on the time taken for the pilgrims to
exit the Tawaf area.
Abstract: State tax revenues in most countries started to decrease during the recession. Government of Latvia decided to compensate the decline by increasing rates of several taxes including excise tax on strong alcohol. The total increase in 2009 constituted 42% and the rate increased from 896€ to 1 266€ for 100l of absolute alcohol. Since then this has had a negative impact on consumption volumes and the split between legal and illegal market. The legal alcohol sales decreased by almost 50% (by volume), consequentially having negative effect on the State revenues from VAT and excise tax. Estimated results for 2010 are indicating 54 million € decrease in VAT, excise tax and other taxes versus 2008 (excise tax -19 million €, VAT -30 million €, other taxes -5 million €). The paper aims to analyze impact of the increase in excise tax on consumption patterns, State revenues and competitiveness of the local companies to draw up proposals for the state authorities regarding more effective tax policies. The analysis reveals a relationship between excise tax rate, illegal alcohol market and State revenues. The results can be used to improve excise tax system and effectiveness in Latvia.
Abstract: Segmentation of Magnetic Resonance Imaging (MRI) images is the most challenging problems in medical imaging. This paper compares the performances of Seed-Based Region Growing (SBRG), Adaptive Network-Based Fuzzy Inference System (ANFIS) and Fuzzy c-Means (FCM) in brain abnormalities segmentation. Controlled experimental data is used, which designed in such a way that prior knowledge of the size of the abnormalities are known. This is done by cutting various sizes of abnormalities and pasting it onto normal brain tissues. The normal tissues or the background are divided into three different categories. The segmentation is done with fifty seven data of each category. The knowledge of the size of the abnormalities by the number of pixels are then compared with segmentation results of three techniques proposed. It was proven that the ANFIS returns the best segmentation performances in light abnormalities, whereas the SBRG on the other hand performed well in dark abnormalities segmentation.
Abstract: In this paper, by introducing twice continuously differentiable mappings, we develop an interior path following following method, which enables us to give a constructive proof of the general Brouwer fixed point theorem and thus to solve fixed point problems in a class of non-convex sets. Under suitable conditions, a smooth path can be proven to exist. This can lead to an implementable globally convergent algorithm. Several numerical examples are given to illustrate the results of this paper.
Abstract: Partial coherence between two signals removing the contribution of a periodic, deterministic signal is proposed for evaluating the interrelationship in multivariate systems. The estimator expression was derived and shown to be independent of such periodic signal. Simulations were used for obtaining its critical value, which were found to be the same as those for Gaussian signals, as well as for evaluating the technique. An Illustration with eletroencephalografic (EEG) signals during photic stimulation is also provided. The application of the proposed technique in both simulation and real EEG data indicate that it seems to be very specific in removing the contribution of periodic sources. The estimate independence of the periodic signal may widen partial coherence application to signal analysis, since it could be used together with simple coherence to test for contamination in signals by a common, periodic noise source.
Abstract: Modes of occurrence of Pb, As, Cr, Co, Cu, and Ni in bituminous coal and lignite were determined by means of sequential extraction using NH4OAc, HCl, HF and HNO3 extraction solutions. Elemental affinities obtained were then evaluated in relation to volatility of these elements during the combustion of these coals in two circulating fluidised-bed power stations. It was found out that higher percentage of the elements bound in silicates brought about lower volatility, while higher elemental proportion with monosulphides association (or bound as exchangeable ion) resulted in higher volatility. The only exception was the behavior of arsenic, whose volatility depended on amount of limestone added during the combustion process (as desulphurisation additive) rather than to its association in coal.
Abstract: We present a theory for optimal filtering of infinite sets of random signals. There are several new distinctive features of the proposed approach. First, we provide a single optimal filter for processing any signal from a given infinite signal set. Second, the filter is presented in the special form of a sum with p terms where each term is represented as a combination of three operations. Each operation is a special stage of the filtering aimed at facilitating the associated numerical work. Third, an iterative scheme is implemented into the filter structure to provide an improvement in the filter performance at each step of the scheme. The final step of the concerns signal compression and decompression. This step is based on the solution of a new rank-constrained matrix approximation problem. The solution to the matrix problem is described in this paper. A rigorous error analysis is given for the new filter.
Abstract: As the use of registration packages spreads, the number of the aligned image pairs in image databases (either by manual or automatic methods) increases dramatically. These image pairs can serve as a set of training data. Correspondingly, the images that are to be registered serve as testing data. In this paper, a novel medical image registration method is proposed which is based on the a priori knowledge of the expected joint intensity distribution estimated from pre-aligned training images. The goal of the registration is to find the optimal transformation such that the distance between the observed joint intensity distribution obtained from the testing image pair and the expected joint intensity distribution obtained from the corresponding training image pair is minimized. The distance is measured using the divergence measure based on Tsallis entropy. Experimental results show that, compared with the widely-used Shannon mutual information as well as Tsallis mutual information, the proposed method is computationally more efficient without sacrificing registration accuracy.
Abstract: Effective estimation of just noticeable distortion (JND) for images is helpful to increase the efficiency of a compression algorithm in which both the statistical redundancy and the perceptual redundancy should be accurately removed. In this paper, we design a DCT-based model for estimating JND profiles of color images. Based on a mathematical model of measuring the base detection threshold for each DCT coefficient in the color component of color images, the luminance masking adjustment, the contrast masking adjustment, and the cross masking adjustment are utilized for luminance component, and the variance-based masking adjustment based on the coefficient variation in the block is proposed for chrominance components. In order to verify the proposed model, the JND estimator is incorporated into the conventional JPEG coder to improve the compression performance. A subjective and fair viewing test is designed to evaluate the visual quality of the coding image under the specified viewing condition. The simulation results show that the JPEG coder integrated with the proposed DCT-based JND model gives better coding bit rates at visually lossless quality for a variety of color images.
Abstract: Exponentially weighted moving average control chart (EWMA) is a popular chart used for detecting shift in the mean of parameter of distributions in quality control. The objective of this paper is to compare the efficiency of control chart to detect an increases in the mean of a process. In particular, we compared the Maximum Exponentially Weighted Moving Average (MaxEWMA) and Maximum Generally Weighted Moving Average (MaxGWMA) control charts when the observations are Exponential distribution. The criteria for evaluate the performance of control chart is called, the Average Run Length (ARL). The result of comparison show that in the case of process is small sample size, the MaxEWMA control chart is more efficiency to detect shift in the process mean than MaxGWMA control chart. For the case of large sample size, the MaxEWMA control chart is more sensitive to detect small shift in the process mean than MaxGWMA control chart, and when the process is a large shift in mean, the MaxGWMA control chart is more sensitive to detect mean shift than MaxEWMA control chart.
Abstract: This study assessed fish marketing as panacea towards
sustainable agriculture in Ogun State, Nigeria. Multi-stage sampling
technique was used in the selection of 150 fish marketers for this
study. Descriptive statistics were used for the objectives while
Product Pearson Moment Correlation was used to test the hypothesis.
Result of the findings revealed that the mean age of the respondents
was 38.60 years. Majority (93.33%) of the respondents had
acceptable levels of formal education. Many (44.00%) of the
respondents had spent 1-5 years in fish marketing. The average
quantity of fish sold in a day was 94.10kg. However, efficient fish
marketing were hindered by inadequate processing equipment,
storage rooms and ice holding facilities (86.67%). There was a
significant relationship between socio-economic characteristics and
profit realized from fish marketing (p < 0.05). It was recommended
that storage and warehousing facilities should be provided to the fish
marketers in the study area.
Abstract: This paper is proposed the dynamic simulation of
small power induction motor based on Mathematical modeling. The
dynamic simulation is one of the key steps in the validation of the
design process of the motor drive systems and it is needed for
eliminating inadvertent design mistakes and the resulting error in the
prototype construction and testing. This paper demonstrates the
simulation of steady-state performance of induction motor by
MATLAB Program Three phase 3 hp induction motor is modeled
and simulated with SIMULINK model.
Abstract: Simulation model is an easy way to build up models
to represent real life scenarios, to identify bottlenecks and to enhance
system performance. Using a valid simulation model may give
several advantages in creating better manufacturing design in order to
improve the system performances. This paper presents result of
implementing a simulation model to design hard disk drive
manufacturing process by applying line balancing to improve both
productivity and quality of hard disk drive process. The line balance
efficiency showed 86% decrease in work in process, output was
increased by an average of 80%, average time in the system was
decreased 86% and waiting time was decreased 90%.
Abstract: The objective of this study is to determine the thermal comfort among worker at Malaysian automotive industry. One critical manual assembly workstation had been chosen as a subject for the study. The human subjects for the study constitute operators at Body Assembly Station of the factory. The environment examined was the Relative Humidity (%), Airflow (m/s), Air Temperature (°C) and Radiant Temperature (°C) of the surrounding workstation area. The environmental factors were measured using Babuc apparatus, which is capable to measure simultaneously those mentioned environmental factors. The time series data of fluctuating level of factors were plotted to identify the significant changes of factors. Then thermal comfort of the workers were assessed by using ISO Standard 7730 Thermal sensation scale by using Predicted Mean Vote (PMV). Further Predicted percentage dissatisfied (PPD) is used to estimate the thermal comfort satisfaction of the occupant. Finally the PPD versus PMV were plotted to present the thermal comfort scenario of workers involved in related workstation. The result of PMV at the related industry is between 1.8 and 2.3, where PPD at that building is between 60% to 84%. The survey result indicated that the temperature more influenced comfort to the occupants