Abstract: In vitro gastro-duodenal digestion model was used to investigate the changes of emulsions under digestion conditions. Oil in water emulsions stabilized by whey proteins (2%) and stabilized by whey proteins (2%) with addition of carboxymethyl cellulose (0.75%) as gelling agent of continuous phase were prepared at pH7. Both emulsions were destabilized under gastric conditions; however the protective role of carboxymethyl cellulose was indicated by recording delay of fat digestibility of this emulsion. In the presence of carboxymethyl cellulose whey proteins on the interfacial surface of droplets were more resistant to gastric degradation causing limited hydrolysis of fat due to the poor acceptability of lipids for the enzymes. Studies of emulsions using in vivo model supported results from in vitro studies. Lower content of triglycerides in blood serum and higher amount of fecal fat of rats were determined when rats were fed by diet containing emulsion made with whey proteins and carboxymethyl cellulose.
Abstract: In this paper we propose a method which improves the efficiency of video coding. Our method combines an adaptive GOP (group of pictures) structure and the shot cut detection. We have analyzed different approaches for shot cut detection with aim to choose the most appropriate one. The next step is to situate N frames to the positions of detected cuts during the process of video encoding. Finally the efficiency of the proposed method is confirmed by simulations and the obtained results are compared with fixed GOP structures of sizes 4, 8, 12, 16, 32, 64, 128 and GOP structure with length of entire video. Proposed method achieved the gain in bit rate from 0.37% to 50.59%, while providing PSNR (Peak Signal-to-Noise Ratio) gain from 1.33% to 0.26% in comparison to simulated fixed GOP structures.
Abstract: Real world Speaker Identification (SI) application
differs from ideal or laboratory conditions causing perturbations that
leads to a mismatch between the training and testing environment
and degrade the performance drastically. Many strategies have been
adopted to cope with acoustical degradation; wavelet based Bayesian
marginal model is one of them. But Bayesian marginal models
cannot model the inter-scale statistical dependencies of different
wavelet scales. Simple nonlinear estimators for wavelet based
denoising assume that the wavelet coefficients in different scales are
independent in nature. However wavelet coefficients have significant
inter-scale dependency. This paper enhances this inter-scale
dependency property by a Circularly Symmetric Probability Density
Function (CS-PDF) related to the family of Spherically Invariant
Random Processes (SIRPs) in Log Gabor Wavelet (LGW) domain
and corresponding joint shrinkage estimator is derived by Maximum
a Posteriori (MAP) estimator. A framework is proposed based on
these to denoise speech signal for automatic speaker identification
problems. The robustness of the proposed framework is tested for
Text Independent Speaker Identification application on 100 speakers
of POLYCOST and 100 speakers of YOHO speech database in three
different noise environments. Experimental results show that the
proposed estimator yields a higher improvement in identification
accuracy compared to other estimators on popular Gaussian Mixture
Model (GMM) based speaker model and Mel-Frequency Cepstral
Coefficient (MFCC) features.
Abstract: Mutations of the telomeric copy of the survival motor neuron 1 (SMN1) gene cause spinal muscular atrophy. A deletion of the Eef1a2 gene leads to lower motor neuron degeneration in wasted mice. Indirect evidences have been shown that the eEF1A protein family may interact with SMN, and our previous study showed that abnormalities of neuromuscular junctions in wasted mice were similar to those of Smn mutant mice. To determine potential colocalization between SMN and tissue-specific translation elongation factor 1A2 (eEF1A2), an immunochemical analysis of HeLa cells transfected with the plasmid pcDNA3.1(+)C-hEEF1A2- myc and a new quantitative test of colocalization by intensity correlation analysis (ICA) was used to explore the association of SMN and eEF1A2. Here the results showed that eEF1A2 redistributed from the cytoplasm to the nucleus in response to serum and epidermal growth factor. In the cytoplasm, compelling evidence showed that staining for myc-tagged eEF1A2 varied in synchrony with that for SMN, consistent with the formation of a SMN-eEF1A2 complex in the cytoplasm of HeLa cells. These findings suggest that eEF1A2 may colocalize with SMN in the cytoplasm and may be a component of the SMN complex. However, the limitation of the ICA method is an inability to resolve colocalization in components of small organelles such as the nucleus.
Abstract: We study different types of aggregation operators and
the decision making process with minimization of regret. We analyze
the original work developed by Savage and the recent work
developed by Yager that generalizes the MMR method creating a
parameterized family of minimal regret methods by using the ordered
weighted averaging (OWA) operator. We suggest a new method that
uses different types of geometric operators such as the weighted
geometric mean or the ordered weighted geometric operator (OWG)
to generalize the MMR method obtaining a new parameterized family
of minimal regret methods. The main result obtained in this method
is that it allows to aggregate negative numbers in the OWG operator.
Finally, we give an illustrative example.
Abstract: This paper presents a new and efficient approach for capacitor placement in radial distribution systems that determine the optimal locations and size of capacitor with an objective of improving the voltage profile and reduction of power loss. The solution methodology has two parts: in part one the loss sensitivity factors are used to select the candidate locations for the capacitor placement and in part two a new algorithm that employs Plant growth Simulation Algorithm (PGSA) is used to estimate the optimal size of capacitors at the optimal buses determined in part one. The main advantage of the proposed method is that it does not require any external control parameters. The other advantage is that it handles the objective function and the constraints separately, avoiding the trouble to determine the barrier factors. The proposed method is applied to 9, 34, and 85-bus radial distribution systems. The solutions obtained by the proposed method are compared with other methods. The proposed method has outperformed the other methods in terms of the quality of solution.
Abstract: When an assignable cause(s) manifests itself to a multivariate process and the process shifts to an out-of-control condition, a root-cause analysis should be initiated by quality engineers to identify and eliminate the assignable cause(s) affected the process. A root-cause analysis in a multivariate process is more complex compared to a univariate process. In the case of a process involved several correlated variables an effective root-cause analysis can be only experienced when it is possible to identify the required knowledge including the out-of-control condition, the change point, and the variable(s) responsible to the out-of-control condition, all simultaneously. Although literature addresses different schemes to monitor multivariate processes, one can find few scientific reports focused on all the required knowledge. To the best of the author’s knowledge this is the first time that a multi task model based on artificial neural network (ANN) is reported to monitor all the required knowledge at the same time for a multivariate process with more than two correlated quality characteristics. The performance of the proposed scheme is evaluated numerically when different step shifts affect the mean vector. Average run length is used to investigate the performance of the proposed multi task model. The simulated results indicate the multi task scheme performs all the required knowledge effectively.
Abstract: The main emphasis of metallurgists has been to process the materials to obtain the balanced mechanical properties for the given application. One of the processing routes to alter the properties is heat treatment. Nearly 90% of the structural applications are related to the medium carbon an alloyed steels and hence are regarded as structural steels. The major requirement in the conventional steel is to improve workability, toughness, hardness and grain refinement. In this view, it is proposed to study the mechanical and tribological properties of unalloyed structural (AISI 1140) steel with different thermal (heat) treatments like annealing, normalizing, tempering and hardening and compared with as brought (cold worked) specimen. All heat treatments are carried out in atmospheric condition. Hardening treatment improves hardness of the material, a marginal decrease in hardness value with improved ductility is observed in tempering. Annealing and normalizing improve ductility of the specimen. Normalized specimen shows ultimate ductility. Hardened specimen shows highest wear resistance in the initial period of slide wear where as above 25KM of sliding distance, as brought steel dominates the hardened specimen. Both mild and severe wear regions are observed. Microstructural analysis shows the existence of pearlitic structure in normalized specimen, lath martensitic structure in hardened, pearlitic, ferritic structure in annealed specimen.
Abstract: In this paper, the energy performance of a selected
UHDE Ammonia plant is optimized by conducting heat integration through waste heat recovery and the synthesis of a heat exchange
network (HEN). Minimum hot and cold utility requirements were estimated through IChemE spreadsheet. Supporting simulation was
carried out using HYSYS software. The results showed that there is
no need for heating utility while the required cold utility was found to
be around 268,714 kW. Hence a threshold pinch case was faced. Then, the hot and cold streams were matched appropriately. Also,
waste heat recovered resulted with savings in HP and LP steams of
approximately 51.0% and 99.6%, respectively. An economic analysis
on proposed HEN showed very attractive overall payback period not
exceeding 3 years. In general, a net saving approaching 35% was
achieved in implementing heat optimization of current studied UHDE Ammonia process.
Abstract: In this paper the features of multiple material gate
silicon-on-insulator MOSFETs are presented and compared with
single material gate silicon-on-insulator MOSFET structures. The
results indicate that the multiple material gate structures reduce short
channel effects such as drain induce barrier lowering, hot electron
effect and better current characteristics in comparison with single
material structures
Abstract: The present study examines the mediating effect of
online flow experience on the relationship between extraversionintroversion,
locus of control and loneliness, and depression and
satisfaction with life. The data was obtained using a structured
questionnaire prepared by adapting standardized scales available from
a sample of 102 engineering students from different technical
institutions at Bhubaneswar, India. The results indicate that there is a
positive significant relationship between introversion, external locus
of control, loneliness, depression and online flow experience, and
extraversion, internal locus of control and satisfaction with life. The
results also suggest that online flow experience mediates the
relationship between the aforementioned variables.
Abstract: In this paper, fabrication and study of electronic properties of Au/methyl-red/Ag surface type Schottky diode by current-voltage (I-V) method has been reported. The I-V characteristics of the Schottky diode showed the good rectifying behavior. The values of ideality factor n and barrier height b of Au/methyl-red/Ag Schottky diode were calculated from the semi-log I-V characteristics and by using the Cheung functions. From semi-log current-voltage characteristics the values of n and b were found 1.93 and 0.254 eV, respectively, while by using Cheung functions their values were calculated 1.89 and 0.26 eV, respectively. The effect of series resistance was also analyzed by Cheung functions. The series resistance RS values were determined from dV/d(lnI)–I and H(I)–I graphs and were found to be 1.1 k and 1.3 k, respectively.
Abstract: Promoting critical thinking (CT) in an educational
setting has been appraised in order to enhance learning and
intellectual skills. In this study, a pedagogical course in a vocational
teacher education program in Turkey was designed by integrating CT
skill-based strategies/activities into the course content and CT skills
were means leading to intended course objectives. The purpose of the
study was to evaluate the importance of the course objectives, the
attainment of the objectives, and the effectiveness of teachinglearning
strategies/activities from prospective teachers- points of
view. The results revealed that although the students mostly
considered the course objectives important, they did not feel
competent in the attainment of all objectives especially in those
related to the main topic of Learning and those requiring higher order
thinking skills. On the other hand, the students considered the course
activities effective for learning and for the development of thinking
skills, especially, in interpreting, comparing, questioning,
contrasting, and forming relationships.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: In this paper, the techniques for estimating the
residual stress in high velocity oxy fuel thermal spray coatings have
been discussed and compared. The development trend and the last
investigation have been studied. It is seemed that the there is not
effective study on the effect of the peening action in HVOF
analytically and numerically.
Abstract: Optimal design of structure has a main role in reduction of material usage which leads to deduction in the final cost of construction projects. Evolutionary approaches are found to be more successful techniques for solving size and shape structural optimization problem since it uses a stochastic random search instead of a gradient search. By reviewing the recent literature works the problem found was the optimization of weight. A new meta-heuristic algorithm called as Cuckoo Search (CS) Algorithm has used for the optimization of the total weight of the truss structures. This paper has used set of 10 bars and 25 bars trusses for the testing purpose. The main objective of this work is to reduce the number of iterations, weight and the total time consumption. In order to demonstrate the effectiveness of the present method, minimum weight design of truss structures is performed and the results of the CS are compared with other algorithms.
Abstract: At the time where electronic books, or e-Books, offer
students a fun way of learning , teachers who are used to the paper
text books may find it as a new challenge to use it as a part of
learning process. Precisely, there are various types of e-Books
available to suit students- knowledge, characteristics, abilities, and
interests. The paper discusses teachers- perceptions on the use of ebooks
as a paper text book in the classroom. A survey was conducted
on 72 teachers who use e-books as textbooks. It was discovered that a
majority of these teachers had good perceptions on the use of ebooks.
However, they had little problems using the devices. It can be
overcome with some strategies and a suggested framework.
Abstract: The effects of commercial or bovine yeasts on the
performance and blood variables of broiler chickens intoxicated with
aflatoxin were investigated in broilers. Four hundred eighty broilers
(Arbor Acres; 3-wk-old) were randomly assigned to 4 groups. Each
group (120 broiler chickens) was further randomly divided into 6
replicates of 20 chickens. The treatments were control diet without
additives (treatment 1), 250 ppb AFB1 (treatment 2), commercial
yeast, Saccharomyces cerevisiae, (CY 2.5 x 107 CFU/g) + 250 ppb
AFB1 (treatment 3) and bovine yeast, Saccharomyces cerevisiae,
(BY 2.5 x 107 CFU/g + 250 ppb AFB1 (treatment 4). Complete
randomized design (CRD) was used in the experiment. Feed
consumption and body weight were recorded at every five-day
period. On day 42, carcass compositions were determined from 30
birds per treatment. While chicks were sacrificed, 3-4 ml blood
sample was taken and stored frozen at (-20°C) for serum chemical
analysis to determine effects of consumption of diets on blood
chemistry (total protein, albumin, glucose, urea, cholesterol and
triglycerides). There were no significant differences in ADFI among
the treatments(P>0.05). However, BWG, FCR and mortality were
highly significantly different (P
Abstract: Human Resource (HR) applications can be used to
provide fair and consistent decisions, and to improve the
effectiveness of decision making processes. Besides that, among
the challenge for HR professionals is to manage organization
talents, especially to ensure the right person for the right job at the
right time. For that reason, in this article, we attempt to describe
the potential to implement one of the talent management tasks i.e.
identifying existing talent by predicting their performance as one of
HR application for talent management. This study suggests the
potential HR system architecture for talent forecasting by using
past experience knowledge known as Knowledge Discovery in
Database (KDD) or Data Mining. This article consists of three
main parts; the first part deals with the overview of HR
applications, the prediction techniques and application, the general
view of Data mining and the basic concept of talent management
in HRM. The second part is to understand the use of Data Mining
technique in order to solve one of the talent management tasks, and
the third part is to propose the potential HR system architecture for
talent forecasting.
Abstract: A multiphase harmonic load flow algorithm is developed based on backward/forward sweep to examine the effects of various factors on the neutral to earth voltage (NEV), including unsymmetrical system configuration, load unbalance and harmonic injection. The proposed algorithm composes fundamental frequency and harmonic frequencies power flows. The algorithm and the associated models are tested on IEEE 13 bus system. The magnitude of NEV is investigated under various conditions of the number of grounding rods per feeder lengths, the grounding rods resistance and the grounding resistance of the in feeding source. Additionally, the harmonic injection of nonlinear loads has been considered and its influences on NEV under different conditions are shown.