Abstract: The study is a review of the literature concerning the
consequences of non-standard monetary policy, which are used by
central banks during unconventional periods, threatening banking
sector instability. In particular, the attention was paid to the effects of
non-standard monetary policy tools for financial markets. However,
the empirical evidence about their effects and real consequences for
financial markets is still not final. The main aim of the study is to
survey consequences of standard and non-standard monetary policy
instruments, implemented during the global financial crisis in the
United States, United Kingdom and euro area, with particular
attention to the results for the stabilization of global financial
markets. The study consists mainly of the empirical review,
indicating the impact of the implementation of these tools for
financial markets. The following research methods were used in the
study: literature studies, including domestic and foreign literature,
cause and effect analysis and statistical analysis.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.
Abstract: Prior to quantifying the variables of the information
model for using school terminology in Croatia's region of Dalmatia
from 1884 to 2014, the most relevant model variables had to be
determined: historical circumstances, standard of living, education
system, linguistic situation, and media. The research findings show
that there was no significant transfer of the 1884 school terms into
1949 usage; likewise, the 1949 school terms were not widely used in
2014. On the other hand, the research revealed that the meaning of
school terms changed over the decades. The quantification of the
variables will serve as the groundwork for creating an information
model for using school terminology in Dalmatia from 1884 to 2014
and for defining direct growth rates in further research.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index
Abstract: Mahasweta Devi and Toni Morrison are the two
stalwarts of the Indian English and the Afro-American literature
respectively. The writings of these two novelists are authentic and
powerful records of the lives of the people because much of their
personal experiences have gone into the making of their works. Devi,
a representative force of the Indian English literature, is also a social
activist working with the tribals of Bihar, Jharkhand, Orissa and West
Bengal. Most of her works echo the lives and struggles of the
subalterns as is evident in her “best beloved book” Chotti Munda and
His Arrow. The novelist focuses on the struggle of the tribals against
the colonial and the feudal powers to create their own identity,
thereby, embarking on the ideological project of ‘setting the record
straight’. The Nobel Laureate Toni Morrison, on the other hand,
brings to the fore the crucial issues of gender, race and class in many
of her significant works. In one of her representative works Sula, the
protagonist emerges as a non- conformist and directly confronts the
notion of a ‘good woman’ nurtured by the community of the Blacks.
In addition to this, the struggle of the Blacks against the White
domination, also become an important theme of the text. The thrust
of the paper lies in making a critical analysis of the portrayal of the
heroic attempts of the subaltern protagonist and the artistic endeavor
of the novelists in challenging the stereotypes.
Abstract: Burnishing is increasingly used as a finishing operation to improve surface roughness and surface hardness. This can be achieved by applying a hard ball or roller onto metallic surfaces under pressure, in order to achieve many advantages in the metallic surface. In the present work, the feed rate, speed and force have been considered as the basic burnishing parameters to study the surface roughness and surface hardness of metallic matrix composites. The considered metal matrix composites were made from Aluminum-Magnesium-Graphite with five different weight percentage of graphite. Both effects of burnishing parameters mentioned above and the graphite percentage on the surface hardness and surface roughness of the metallic matrix composites were studied. The results of this investigation showed that the surface hardness of the metallic composites increases with the increase of the burnishing force and decreases with the increase in the burnishing feed rate and burnishing speed. The surface roughness of the metallic composites decreases with the increasing of the burnishing force, feed rate, and speed to certain values, then it starts to increase. On the other hand, the increase in the weight percentage of the graphite in the considered composites causes a decrease in the surface hardness and an increase in the surface roughness.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: In order to better understand the long term
implications of the grout wear failure mode in large-diameter plainsided
grouted connections, a numerical model has been developed
and calibrated that can take advantage of existing operational plant
data to predict the wear accumulation for the actual load conditions
experienced over a given period, thus limiting the requirement for
expensive monitoring systems. This model has been derived and
calibrated based on site structural condition monitoring (SCM) data
and supervisory control and data acquisition systems (SCADA) data
for two operational wind turbine generator substructures afflicted
with this challenge, along with experimentally derived wear rates.
Abstract: Rotary draw bending is a method which is being used
in tube forming. In the tube bending process, the neutral axis moves
towards the inner arc and the wall thickness distribution changes for
tube’s cross section. Thinning takes place in the outer arc of the tube
(extrados) due to the stretching of the material, whereas thickening
occurs in the inner arc of the tube (intrados) due to the comparison of
the material. The calculations of the wall thickness distribution,
neutral axis shifting, and strain distribution have not been accurate
enough, so far. The previous model (the geometrical model)
describes the neutral axis shifting and wall thickness distribution. The
geometrical of the tube, bending radius and bending angle are
considered in the geometrical model, while the influence of the
material properties of the tube forming are ignored. The advanced
model is a modification of the previous model using material
properties that depends on the correction factor. The correction factor
is a purely empirically determined factor. The advanced model was
compared with the Finite element simulation (FE simulation) using a
different bending factor (Bf =bending radius/ diameter of the tube),
wall thickness (Wf = diameter of the tube/ wall thickness), and
material properties (strain hardening exponent). Finite element model
of rotary draw bending has been performed in PAM-TUBE program
(version: 2012). Results from the advanced model resemble the FE
simulation and the experimental test.
Abstract: The effect of the inclusion of thyme and rosemary
essential oils into chitosan films, as well as the microbiological and
physical properties when storing chitosan film with and without the
mentioned inclusion was studied. The film forming solution was
prepared by dissolving chitosan (2%, w/v), polysorbate 80 (4% w/w
CH) and glycerol (16% w/w CH) in aqueous lactic acid solutions
(control). The thyme (TEO) and rosemary (REO) essential oils (EOs)
were included 1:1 w/w (EOs:CH) on their combination 50/50
(TEO:REO). The films were stored at temperatures of 5, 20, 33°C
and a relative humidity of 75% during four weeks. The films with
essential oil inclusion did not show an antimicrobial activity against
strains. This behavior could be explained because the chitosan only
inhibits the growth of microorganisms in direct contact with the
active sites. However, the inhibition capacity of TEO was higher than
the REO and a synergic effect between TEO:REO was found for S.
enteritidis strains in the chitosan solution.
Some physical properties were modified by the inclusion of
essential oils. The addition of essential oils does not affect the
mechanical properties (tensile strength, elongation at break, puncture
deformation), the water solubility, the swelling index nor the DSC
behavior. However, the essential oil inclusion can significantly
decrease the thickness, the moisture content, and the L* value of
films whereas the b* value increased due to molecular interactions
between the polymeric matrix, the loosing of the structure, and the
chemical modifications. On the other hand, the temperature and time
of storage changed some physical properties on the chitosan films.
This could have occurred because of chemical changes, such as
swelling in the presence of high humidity air and the reacetylation of
amino groups. In the majority of cases, properties such as moisture
content, tensile strength, elongation at break, puncture deformation,
a*, b*, chrome, 7E increased whereas water resistance, swelling
index, L*, and hue angle decreased.
Abstract: In this paper, the transient device performance analysis
of n-type Gate Inside JunctionLess Transistor (GI-JLT) has been
evaluated. 3-D Bohm Quantum Potential (BQP) transport device
simulation has been used to evaluate the delay and power dissipation
performance. GI-JLT has a number of desirable device parameters
such as reduced propagation delay, dynamic power dissipation,
power and delay product, intrinsic gate delay and energy delay
product as compared to Gate-all-around transistors GAA-JLT. In
addition to this, various other device performance parameters namely,
on/off current ratio, short channel effects (SCE), transconductance
Generation Factor (TGF) and unity gain cut-off frequency (fT ) and
subthreshold slope (SS) of the GI-JLT and GAA-JLT have been
analyzed and compared. GI-JLT shows better device performance
characteristics than GAA-JLT for low power and high frequency
applications, because of its larger gate electrostatic control on the
device operation.
Abstract: Fugitive particulate matter (PM) is a major source of
airborne pollution in the Middle East countries. The meteorological
conditions and topography of the area makes it highly susceptible to
wind-blown particles which raise many air quality concerns. Air
quality tools such as field monitoring, emission factors and dispersion
modeling have been used in previous research studies to analyze the
release and impacts of fugitive PM in the region. However, these
tools have been originally developed based on experiments made for
European and North American regions. In this work, an experimental
campaign was conducted on April-May 2014 in a construction site in
Doha city, Qatar. The ultimate goal is to evaluate the applicability of
the existing emission factors for construction sites in dry and arid
areas like the Middle East.
Abstract: The Roma (Gypsies) is a transnational minority with a
high degree of consanguineous marriages. Similar to other
genetically isolated founder populations, the Roma harbor a number
of unique or rare genetic disorders. This paper discusses about a rare
form of Charcot-Marie-Tooth disease – type 4G (CMT4G), also
called Hereditary Motor and Sensory Neuropathy type Russe, an
autosomal recessive disease caused by mutation private to Roma
characterized by abnormally increased density of non-myelinated
axons. CMT4G was originally found in Bulgarian Roma and in 2009
two putative causative mutations in the HK1 gene were identified.
Since then, several cases were reported in Roma families mainly
from Bulgaria and Spain. Here we present a Slovak Roma family in
which CMT4G was diagnosed on the basis of clinical examination
and genetic testing. This case is a further proof of the role of the HK1
gene in pathogenesis of the disease. It confirms that mutation in the
HK1 gene is a common cause of autosomal recessive CMT disease in
Roma and should be considered as a common part of a diagnostic
procedure.
Abstract: A feeding experiment was conducted to determine the
optimum dietary protein and lipid levels for juvenile fancy carp. Eight
experimental diets were formulated to contain four protein levels (200,
300, 400 and 500 g kg-1) with two lipid levels (70 and 140 g kg-1).
Triplicate groups of fish (initial weight, 12.1±0.2 g fish-1) were
hand-fed the diets to apparent satiation for 8 weeks. Fish growth
performance, feed utilization and feed intake were significantly
(P0.05). Weight gain and feed efficiency ratio tended to
increase as dietary protein level increased up to 400 and 500 g kg-1,
respectively. Daily feed intake of fish decreased with increasing
dietary protein level and that of fish fed diet contained 500 g kg-1
protein was significantly lower than other fish groups. The protein
efficiency ratio of fish fed 400 and 500 g kg-1 protein was lower than
that of fish fed 200 and 300 g kg-1 protein. Moisture, crude protein and
crude lipid contents of muscle and liver were significantly affected by
dietary protein, but not by dietary lipid level (P>0.05). The increase in
dietary lipid level resulted in an increase in linoleic acid in liver and
muscle paralleled with a decrease in n-3 highly unsaturated fatty acids
content in muscle of fish. In considering these results, it was concluded
that the diet containing 400 g kg-1 protein with 70 g kg-1 lipid level is
optimal for growth and efficient feed utilization of juvenile fancy carp.
Abstract: This paper presents optimization of makespan for ‘n’
jobs and ‘m’ machines flexible job shop scheduling problem with
sequence dependent setup time using genetic algorithm (GA)
approach. A restart scheme has also been applied to prevent the
premature convergence. Two case studies are taken into
consideration. Results are obtained by considering crossover
probability (pc = 0.85) and mutation probability (pm = 0.15). Five
simulation runs for each case study are taken and minimum value
among them is taken as optimal makespan. Results indicate that
optimal makespan can be achieved with more than one sequence of
jobs in a production order.
Abstract: Given the importance of ports as links in the global
supply chains and because they are key elements to induce
competitiveness in their hinterlands, the number of studies devoted to
port governance, management and operations has increased in the last
decades. Some of these studies address the port governance model as
an element to improve coordination among the actors of the portlogistics
chain and to generate a better port performance. In this
context, the present study analyzes the governance of Port of Santos
through individual interviews with port managers, based on a
conceptual model that considers the key dimensions associated with
port governance. The results reinforce the usefulness of the applied
model and highlight some existing improvement opportunities in the
port studied.
Abstract: In this study, attempt has been made to investigate the
relationship specifically the causal relation between fund unit prices
of Islamic equity unit trust fund which measure by fund NAV and the
selected macro-economic variables of Malaysian economy by using
VECM causality test and Granger causality test. Monthly data has
been used from Jan, 2006 to Dec, 2012 for all the variables. The
findings of the study showed that industrial production index,
political election and financial crisis are the only variables having
unidirectional causal relationship with fund unit price. However the
global oil price is having bidirectional causality with fund NAV.
Thus, it is concluded that the equity unit trust fund industry in
Malaysia is an inefficient market with respect to the industrial
production index, global oil prices, political election and financial
crisis. However the market is approaching towards informational
efficiency at least with respect to four macroeconomic variables,
treasury bill rate, money supply, foreign exchange rate, and
corruption index.
Abstract: Nowadays social media information, such as news,
links, images, or VDOs, is shared extensively. However, the
effectiveness of disseminating information through social media
lacks in quality: less fact checking, more biases, and several rumors.
Many researchers have investigated about credibility on Twitter, but
there is no the research report about credibility information on
Facebook. This paper proposes features for measuring credibility on
Facebook information. We developed the system for credibility on
Facebook. First, we have developed FB credibility evaluator for
measuring credibility of each post by manual human’s labelling. We
then collected the training data for creating a model using Support
Vector Machine (SVM). Secondly, we developed a chrome extension
of FB credibility for Facebook users to evaluate the credibility of
each post. Based on the usage analysis of our FB credibility chrome
extension, about 81% of users’ responses agree with suggested
credibility automatically computed by the proposed system.
Abstract: In order to manufacture short gap single Si nanowire
(NW) field effect transistor (FET) by imprinting and transferring
method, we introduce the method using Al2O3 sacrificial layer. The
diameters of cylindrical Si NW addressed between Au electrodes by
dielectrophoretic (DEP) alignment method are controlled to 106, 128,
and 148 nm. After imprinting and transfer process, cylindrical Si NW
is embedded in PVP adhesive and dielectric layer. By curing
transferred cylindrical Si NW and Au electrodes on PVP-coated p++ Si
substrate with 200nm-thick SiO2, 3μm gap Si NW FET fabrication
was completed. As the diameter of embedded Si NW increases, the
mobility of FET increases from 80.51 to 121.24 cm2/V·s and the
threshold voltage moves from –7.17 to –2.44 V because the ratio of
surface to volume gets reduced.